Baicells Technologies ATOM OD06 3.5GHz 14dBi Outdoor CPE User Manual
- June 5, 2024
- Baicells Technologies
Table of Contents
Technologies ATOM OD06 3.5GHz 14dBi Outdoor
CPE User Manual
ATOM OD06 – EG7010C-M11 USER Manual
All rights reserved © Baicells Technologies Co., Ltd.
Shipping List
Make sure you have got the following parts: EG7010C
Hardware Introduction
**2.1 Indicators
**
Identity| Description| Color| Status|
Description
---|---|---|---|---
MIU| –| Yellow| OFF| Reserved.
Steady On| Reserved.
Blanking| Reserved.
LTE| Network state Indicator|
Blue
| OFF| LTE disconnected.
Steady On| LTE connected.
SIM| SIM status indicator Card| Yellow| Steady On| The SIM card is normal.
Blanking| The SIM card is abnormally Or not inserted.
LAN| 100Mbps Eth Indication| Yellow| OFF| Ethernet connection does not
establish.
Steady On| The ethernet connection is normal.
Blanking| Data is transmitted.
PWR| Power Indicator| Yellow| OFF| No Power Supply
Steady On| Power On
LTE Signal| 5 LTEs Indicate| Green| All OFF| The signal is too weak to attack.
Steady On| According to signal strength in turn light
Identity| Description| Color| Status| Description
---|---|---|---|---
| connection state and
signal
strength| | | up
Blanking| Scanning the LTE network
The CPE is authenticating.
CPE is getting IP addresses from the LTE network.
2.2 Interface and Buttons
Interface & Button
|
Description
---|---
PoE| Connected to the PoE Power Adapter
TF| Support SD card
SIM| Support 1.8V/3.0V USIM 2FF
RESET| Long press over 10 seconds to restore the factory settings
GND| Connected to Earth by conductor
Installation Guide
3.1 Support Materials
Before installation, prepare the following support materials accordingly,
as given below:
| Item | Description |
|---|---|
| Ethernet cable | Outdoor Shield CAT5E Shorter than 330 feet |
| Ground wire | 16mm² yellow-green wire |
3.2 Install USIM Card and Cables
|
---|---
(1) Screw the screw on the waterproof cover, and open the waterproof cover|
(2) Insert the USIM card to the USIM slot. Note following the directions
|
(3) Connect the Ethernet cable to the PoE port| (4) connect the ground cable
to the ground screw
(5) Close the waterproof cover and fasten the screw on the cover.
(6) Connected Ethernet cable to the power adapter. Pay attention to the
power adapter interface directions.
(7) Power on, the LED indicator will light up.
3.3 Install on Wall
-
Slipping the bracket from the CPE.
-
Fit the CPE on the wall, and mark the drilling locations.
-
Drill four 10mm diameter and 70mm depth holes in the wall by following the marked locations.
-
Check the up/down direction of the bracket, and then fix it on wall using M5 tapping screws.
-
Install the CPE to the bracket and fasten the screw.
3.4 Install on Pole
-
Round an anti-slip rubber on the pole.
-
Fix the bracket using the hoop.
-
Install the CPE to the bracket and fasten the screw.
3.5 Grounding
The EG7010C-M11 must be grounding, please contact a professional person to
operate. Using the grounding cable, connect the grounding cable to the ground
row
Configuration Guide
4.1 4.1 Login
The CPE manages, configures, and maintains the device by web management page.
The steps to log in are as follows:
-
In the address column of the browser, type in http://192.168.150.1, then press “Enter”:
-
Enter the user name and password, and click “Log in”. After password authentication, you can log on to the web management page. The default user name and password is admin.
For security, it is recommended that you open the firewall, and keep your
login password, WLAN FTP passwords, and passwords well.
4.2 View Status
In the overview area, you can view the device information and LTE status, such
as Product name, Software version, PLMN, IMSI, RSRP, RSRQ, CINR, SINR, Tx
Power, Cell ID, PCI, and so on, as shown below:
SAS Settings, as shown below:
Specifications
Basic Specifications
Item|
Description
---|---
UE-Category| 3GPP R10, CAT 6/7
SIM Slot| 1.8V/3.0V USIM 2FF
Ethernet Port| 1 RJ45, LAN, 10/100/1000 auto-sensing, auto-MDX, PoE
Power Supply| Input: Universal range 100V~240V AC Output: PoE (24V DC, 0.5A)
Reset Button| Tactile button. Long press over 10s to restore the factory
settings
LED Indicators| MIU/LTE/SIM/LAN/PWR/LTE Signal
Dimensions| 241mm (H) x 154mm (W) x 50mm (D)
Weight| About 900 g
LTE Specifications
| Item | Description |
|---|---|
| LTE Mode | LTE-TDD |
| LTE Bands | Band 48 |
| TXRX | 2T4R |
| Channel Bandwidth | 5MHz, 10MHz, 15MHz, 20MHz |
| Modulation | QPSK, 16QAM |
| --- | --- |
| Receive Sensitivity | -94dBm @ QPSK,20MHz, 25°C |
| MAX Output Power | 26dBm |
| Antenna Type | Internal directional-antenna |
| Antenna Gain | 14dBi@3.xGHz, 2 Ports |
| Polarization | ±45° |
| Antenna Efficiency | >70% |
| Isolation | ≤-25dB |
| VSWR | ≤2 |
| Horizontal Beam Width (3dB) | 60±3°@3.xGHz, 2 Ports |
| Vertical Beam Width (3dB) | 25±5°@3.xGHz, 2 Ports |
SW Specifications
Item|
Description
---|---
Language Support| English/Chinese
Network Mode| NAT/Bridge/Tunnel
IP Protocol| IPv4/IPv6
SIM Management| PIN Management, SIM-Lock
Network Connection Management| Auto/Manual
LTE Scan Mode| Full band scan, Frequency Lock
WLAN| WPS
MSSID IsolationVLAN
VPN| L2TP
GRE
NAT| Port forwarding
DMZ
ALG
Port Trigger
---|---
Firewall
| IP/MAC/URL Filter
Access Control
Block Port Scanner / SYN Flood
SPI Filter
Network Management| TR069
SNMP
Diagnostics
| TCPDump
Ping
Trace route
Statistics| LTE Status/Connection Time/System Up Time
Device Status
DHCP Client List
WiFi Station List
LTE Status
Firewall Status
Maintenance| Date & Time setting
Reboot
Restore factory settings
Restore / Back up configuration file
Firmware upgrade locally/OTA (over the air)
System Log
| Operating Log
Run-time Log
Filter/Select/Display/Export Log
Environmental Specifications
Item|
Description
---|---
Operating Temperature| -40°C to 55°C
Storage Temperature| -40°C to 70°C
Operating Humidity| 5% to 95%
Ingress Protection Rating| IP65
Regulatory Compliance
FCC Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. This equipment has
been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 30cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>