bluehive 035-7316-6 Wireless Charging Station with Built-in Smart Watch Holder User Manual

blue hive 035-7316-6 Wireless Charging Station with Built-in Smart Watch

Holder

This charging station allows you to enjoy wireless charging easily. Please rea the user manual before using and keep it for future reference.

Specifications:

• Input: DC 5 V 2 A
• Wireless output: 5 V 1 A
• USB output: 5 V 1 A
• Frequency: 114.40KHz – 147.97KHz
• Charge efficiency: 65%
• Charging distance: ≤ 8 mm

Smartwatch

charger and cable

INSTRUCTIONS:

1. Place the Smart Watch onto the arm
2. Firmly press the charging cable into the route
3. Run the remaining cable through the slot
4. Firmly press the arm into the base
5. Plug the cable into the USB output.

Connecting to the power supply:

1. Connect the USB 2.0 port to the power adaptor (or connect to the laptop), and the micro USB port to the wireless charging dock.
2. The LED indicator will turn to green, entering into standby mode.

Charging function

1. Make sure the wireless charging dock is connected to a power supply and is in standby status.
2. Put the Qi-enabled smartphone on the dock, LED indicator turns to blue for charging.
3. Attach the smartwatch to the watch charger for charging.

Note: if the phone case is metal, please remove before charging. Do not use phone cases thicker 5 mm (3/16″) for wireless charging.

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection agains harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

Warning:

1. Do not squeeze or drop the charging station.
2. Do not disassemble or throw into fre or water to avoid causing short circuit leakage.
3. Do not use wireless chargers in hot, humid or corrosive environments to avoid damage.
4. Do not place wireless charger close to magnetic stripe or chip card (ID card, bank card, etc.) to avoid magnetic failure.
5. Please keep the wireless charger at least 20 cm (7 7/8″) from implantable medical devices (heart pacemakers, implantable cochlea, etc.) to avoid potential interference of the medical devices.
6. Please keep children away from the wireless charger to avoid Made in China Imported by Trileaf Distribution Toronto, Canada M4S 2B8 Product must be recycled or disposed of properly. Dispose of as per the requirements of your local municipality

The ‘Q®i ’ symbol is a trademark of the Wireless Power Consortium.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received,including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>