CAVIUS ApS 9001 Smart Remote Instruction Manual
- June 9, 2024
- CAVIUS
Table of Contents
- GENERAL DESCRIPTION
- SAFETY INSTRUCTIONS
- TECHNICAL INFORMATION
- HOW TO CONNECT TO THE WIRELESS ALARM FAMILY:
- INSTALLATION:
- TEST FUNCTION:
- ALARM MODE:
- HOW TO HUSH AN ALARM USING THE SMART REMOTE:
- FLASHLIGHT:
- LOW BATTERY SIGNAL:
- BATTERIES REPLACEMENT:
- MAINTENANCE & TROUBLESHOOTING:
- HOW THE SMART REMOTE IS BEHAVING:
- OTHER INFORMATION:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ApS 9001 Smart Remote
Instruction Manual
Commercial reference: 9001
Developed by CAVIUS
PLEASE READ THE USER GUIDE C A R E FULLY BEFORE USE AND RETAIN FOR FUTURE USE!
GENERAL DESCRIPTION
The Smart Remote is designed to alert with a rapid flashing warning light when
alarming and to remotely control the CAVIUS Wireless Alarm Family. The torch
function can
be used to find escape routes at night.
SAFETY INSTRUCTIONS
Batteries are to be handled with care and battery powered devices should be kept out of reach of children. Do not try to recharge or burn the batteries.
TECHNICAL INFORMATION
The Smart Remote can be used with the alarms from the CAVIUS Wireless Alarm
Family: Smoke, Heat, Flood and Mains Power alarms. The maximum number of
alarms that can be interlinked with is 32.
The minimum range is 100m in open field. RF conditions also depend on the
house layout and materials. You should always test it after installation and
after changing batteries.
Diameter: 27mm. Length: 140mm.
The Smart Remote is powered by 3 replaceable AAA batteries.
Complies to standards: RoHS, REACH, EN60065.
HOW TO CONNECT TO THE WIRELESS ALARM FAMILY:
Open the battery compartment by pressing the snap. Insert
the batteries in the battery compartment respecting polarities.Slide the learn switch to the “Learn mode” position. The
Smart Remote will go into Learn mode.
All alarms that need to be connected to the Smart Remote in the house should
be put into “Learn mode” by sliding the switch of each device on the “Learn
mode” position.
The flashlight will light up to indicate that “Learn mode” has been
selected. Please note: Do not take out the
batteries during “Learn mode” as this will interrupt the learn process.
Press and hold the test button on an alarm, of your own choice, until it beeps
and the LED flashes. This alarm will become the master and will start sending
out a specific house code to the other alarms.As the other alarms receive
the specific house code, they will also start flashing their red LED’s.
When the red LED light flashes on all alarms, they are
connected and MUST BE SWITCHED OUT OF ‘LEARN MODE’ and installed. Label the
original “Learn” alarm in order to easily add new CAVIUS Wireless Family
alarms to the system.
INSTALLATION:
The body of the Smart Remote has a built-in magnet, so it can be installed on
a metal plate mounted on the wall, or on a fridge or other metal surfaces.
The accompanying metal plate can be installed by the double sided tape or the
enclosed screw set. The end cap has a hole in which a lanyard can be added so
the remote can hang from a hook etc.
TEST FUNCTION:
After installation, and at least once per quarter, test all your alarms by
pressing the test button on the remote to ensure they are operating correctly
and are within range of each other.
It is recommended to check visually every week if the LED flashes correctly on
the alarm (every 48sec.).
Hold the red end button for two swipes of alarms until the remote stops
flashing, sounding and vibrating.
The remote is now transmitting a test signal to your alarms. During the test,
the Smart Remote will flash and sound.
If the Smart Remote is receiving a test signal from another device, it will
also flash and sound to indicate that it is part of the group. Indication can
be stopped by pressing the end button.
Please note: To ensure an optimal operation in normal conditions, test
function sends out a reduced power RF signal.
ALARM MODE:
When one of the connected alarms is going into alarm and sending out the RF
alarm signal, the Smart Remote’s flashlight will start flashing rapidly
(stroboscope).
The Smart remote has a built in vibrator and sounder which will follow the
sound pattern of the originating alarm. During the alarm, both the sounder and
vibrator will be activated.
The torch can be switched from stroboscopic flashing to constant on by
pressing the side button.
Please note: Flashlight will flash at 2 Hertz (2 times each second) to
avoid photo sensitive epilepsy to be triggered.
The CAVIUS Wireless Family has two different alarm signals:
Alarm signal 1 (— — —) is life threatening alarms, like a smoke alarm.
Alarm signal 2 (- – -) is a non life threatening alarm, like a flooding
alarm:
Smoke alarm signal: — — —
Heat alarm signal: — — —
Flood alarm signal: – – –
Please note that only the originating alarm’s LED will flash, so it can
be identified.
HOW TO HUSH AN ALARM USING THE SMART REMOTE:
When the alarms from the Wireless Alarm Family go into alarm, they can be hushed by a short press on the end button of the Smart Remote.
- During the first 30 seconds of an alarm: Press the red end button once and the remote stops sounding and vibrating, LED is still flashing. The remote is now waiting to send out the hush signal which will start automatically within 30 seconds.
- After 30 seconds of an alarm:
Press the red end button once and the remote will send out a hush signal for 13 seconds. If needed to hush several alarms, this can be repeated as many times as necessary.
Please note: Due to coming legislation, the hush signal is transmitted
with reduced power (the remote must be within short range from the silenced
alarm, which means you should be in the same room as the alarm).
You can hush any of your alarms in the system, as long as you are in in the
same room and within short range of the alarm.
You can go from room to room and hush the alarms by short press till you find
the originating alarm (the one that flash), then check the cause of alarm. All
the others devices will be silenced too.
If you hush an alarm other than the source of the alarm, the remaining alarms
will still sound.
FLASHLIGHT:
The flashlight can be activated by pressing the side button. By pressing again
you turn off the light.
Please note: The light will go out automatically after 5 minutes.
LOW BATTERY SIGNAL:
When the battery is starting its end of life, a short beep will sound out every 48 seconds for 30 days. Only the device affected by the low battery will beep, no other connected devices will sound. It is safe to change batteries in the Smart Remote without going through the learn process again – it will not forget the codes during the battery change process.
BATTERIES REPLACEMENT:
You can access the 3 x AAA batteries by removing the end cap.
Replace the batteries respecting polarities. Always test the Smart Remote
after battery replacement.Caution: There is a risk of explosion if the
batteries are replaced by an incorrect type.
MAINTENANCE & TROUBLESHOOTING:
If the Smart Remote does not work when the test/ hush button is pushed, the probable cause is faulty batteries which must be replaced. Please refer to troubleshooting at www.cavius.com.
HOW THE SMART REMOTE IS BEHAVING:
When the remote is:
Receiving a signal from an alarm:
– vibrating, sounding and LED is flashing Waiting to send a hush signal during
the first 30 seconds of an alarm:
– LED is flashing Sending a hush signal:
– quick vibration, sounding and LED is flashing for 13 seconds Receiving a
test signal:
– quick vibration and LED is flashing
OTHER INFORMATION:
Disposal: For battery and product, please dispose properly at the end of life.
This is electronic waste which should be recycled.
Complies to the Radio Equipment Directive 2014/53/EU.
Interlinked by RF: 868 MHz.
Maximum radio-frequency power transmitted: 20 dBm.
Full DoC to 2014/53/EU (RED) can be downloaded at
www.cavius.com
WARNING: All alarms should be assumed as due to actual fire and the
dwelling should be evacuated immediately.
WARNING: Batteries shall not be exposed to excessive heat such as shine,
fire, or the like.
Note the local country regulations regarding installation.
The CE mark affixed to the product confirms compliance with all relevant
European directives along with the Radio Equipment Directive (RED) 2014/53/EU
for all wireless family products.All Rights reserved: CAVIUS Aps assumes no responsibility
for any errors, which may appear in this manual. Furthermore, CAVIUS Aps
reserves the right to alter the hard ware, software, and/or specifications
detailed herein at any time without notice, and CAVIUS Aps does not make any
commitment to update the information contained
herein. All the trademarks listed herein are owned by their respective owners.
Copyright © CAVIUS Aps.
(C) 2022 Carrier . All rights reserved.
Developed by CAVIUS Aps, Jens Juuls Vej 28 K,
DK- 8260. Manufactured in P.R.C.
127747rev3
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>