CAT DM85586 336 Hydraulic Excavator Instruction Manual
- June 5, 2024
- CAT
Table of Contents
- CAT DM85586 336 Hydraulic Excavator
- 336 Hydraulic Excavator OPERATING INSTRUCTIONS
- PACKAGE INCLUDED
- FULL FUNCTION RADIO CONTROL
- INSTALLATION OF REMOTE CONTROL MODEL BATTERY
- BUCKET, STICK, BOOM AND BODY CONTROL
- MODEL DRIVING CONTROL
- Battery Charging Instructions
- INDICATOR LIGHT STATUS AT THE TIME OF CHARGING
- Precautions Of Li-Po Batteries
- Safe Usage Instructions for Li-Po Batteries
- IMPROPER USE OF THIS PRODUCT
- MODEL DRIVING CONTROL
- REMOTRE CONTROL FREQUENCY PAIRING AND POWER ON
- LIGHT AND SOUND CONTROL
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
CAT DM85586 336 Hydraulic Excavator
336 Hydraulic Excavator OPERATING INSTRUCTIONS
PACKAGE INCLUDED
Truck, Controller,
USB charger with cable,
Two AAA batteries, Lithium battery, Window box package
IMPORTANT NOTICES
Changes or modifications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment. The device has
been evaluated to meet general RF exposure requirement, the device can be used
in portable exposure condition without restriction. This device complies with
Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions this device may not cause interference, and this
device must accept any interference,
including interference that may cause undesired operation of the device.
FULL FUNCTION RADIO CONTROL
INSTALLATION OF REMOTE CONTROL MODEL BATTERY
Model is equipped with a 7.4V 600m Ah Li-Po battery included. First, twist the
buckle to open the battery cover, then correctly connect the battery following
the diagram. Place the battery into the compartment. Close the battery cover
and twist the buckle to lock the cover. Tighten the cover screw to avoid
children easy access. INSTALLATION OF
The remote control requires 2 X 1.5V AAA non-rechargeable batteries. Open the
battery cover by loosening the cover screw. Place the batteries into the
compartment observing the correct polarity. Replace the battery cover and
tighten the cover screw.
- Remove rechargeable battery from package and install correctly in machine following included guidelines.
- The rechargeable battery should be removed from the machine before recharging.
- Recharge battery only under adult supervision.
- Do not use rechargeable AAA batteries in the remote control.
- Do not combine old and new AAA batteries in the remote control.
- Use the same type or brand of new AAA batteries in the remote control.
- Place AAA batteries in the remote control observing the correct polarity.
- Use caution to avoid short-circuit of the battery terminals in the remote control.
BUCKET, STICK, BOOM AND BODY CONTROL
MODEL DRIVING CONTROL
Battery Charging Instructions
CHARGING METHODS
Connect the white port of LiPo to USB charging port, as shown in the Figure, and ensure port can be connected tightly and corectly, then insert the USB charging plug into power adapter, and perfom charging.
INDICATOR LIGHT STATUS AT THE TIME OF CHARGING
Uncharged state
red light always lit
Charged state
Red light always lit & Green light flashes
Full charging state
Red and green light always lit
When the battery is fully charged, please remove the USB charger lead promptly
Precautions Of Li-Po Batteries
- Battery can be charged only by originally configured USB charger lead.
- Be sure to charge with the white Big socket port, not the yellow socket.
- 7.4V 600mAh Li-Po must be equipped with 5V USB charging plug.
- Any Li-Po battery with a damaged appearance should NOT be charged tobavoid fire hazards from spontaneous combustion.
- The battery should be charged according to the specified charging time period.
Safe Usage Instructions for Li-Po Batteries
- Li-Po batteries pose a higher danger compared with other batteries.
- This company does not bear any responsibility resulting from improper usage.
- DO NOT attempt to charge the Li-Po battery with any charger other than the included original charger.
- Failure to do so may result in an explosion or fire. DO NOT dismantle, subject to impact, incinerate or reverse the connections of the battery.
- Avoid metal objects impacting the positive and negative polarities of the battery.
- Please prevent sharp objects from penetrating the battery to avoid the potential of fire.
- Please use caution when charging the battery and ensure charging occurs in a visible area.
- DO NOT leave battery unattended while charging.
- Battery should be kept out of reach of children to avoid any injury.
- A degraded battery should not be attempted to be recharged.
- Battery expansion, deformation, explosion or fire may occur.
- Degraded batteries should be disposed of properly following regional or national disposal guidelines to ensure protection of the environment.
WARNING
This product contains small parts and is not intended for children under
the age of 8. The remote control requires 2 X 1.5V AAA non-rechargeable
batteries and the RC model requires a 7.4 V 600mAh Li-Po battery (included)
The RC model motor can generate heat and should not be touched to avoid
possible burns.
Periodically check the wire, plug, shell and other parts of the charger for
wear or damage and discontinue use if detected until repaired or replaced. The
RC model should only be charged using the recommended guidelines. The LEDs
(Light Emitting Diodes) can emit radiation and should not be pointed directly
at the eyes. Aviation restrictions forbid the use of Radio Control devices
within a radius of 3 miles or 5000 meters from any airport runway or facility.
Aviation restrictions forbid the use of Radio Control devices within a radius
of 3 miles or 5000 meters from any airport runway or facility.
IMPROPER USE OF THIS PRODUCT
Do not dismantle, modify or otherwise alter the operation of this product in any manner. Do not operate this product in an unlawful or illegal manner or as to jeopardize the safety of the operator or others.
IMPORTANT NOTICES
FCC STATEMENT
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions this device may not cause harmful interference,
and 2) this device must accept any
interference received, including interference that may may cause undesired
operation. This equipment has been tested and found to comply with the limits
for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation.This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures: Reorient or relocate the receiving antenna. Increase the
separation between the equipment and receiver. Connect the equipment into an
outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
MODEL DRIVING CONTROL
REMOTRE CONTROL FREQUENCY PAIRING AND POWER ON
This product is equipped with a remote control with a frequency of 2.4GHz.
When a user operates the product for the first time, please install batteries
into the model and the remote
control. Then power on the unit, then the remote control. A series of beeps
will indicate that the frequency pairing has been completed and the model is
ready to operate.
LIGHT AND SOUND CONTROL
The operating model can generate lights and sounds Press the sound switch to tun on the lights and sounds press the switch again to tum them off.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>