Conair HCT423R Hair Clipper and Beard Instruction Guide
- June 3, 2024
- ConAir
Table of Contents
Conair HCT423R Hair Clipper and Beard
Specifications
- BRAND: Conair
- MODEL NAME: RA3780
- UNIT COUNT: 1 Count
- POWER SOURCE: Corded Electric
- BLADE MATERIAL: Stainless Steel
- PRODUCT DIMENSIONS: 25 x 7.5 x 11.5 inches; 1.6 Pounds
Introduction
A 24-piece package called the Conair 2-in-1 Clipper and Trimmer/The Chopper Complete Grooming System will keep you looking good. It has two removable blades, one for shaving and the other for cutting hair. A facial trimming blade and a hair clipping blade made of stainless steel are included for precision beard and detail style as well as ultra-close bald and fade styling. This kit for men’s haircuts features a grip that will not slip and a 5-position taper control. While other stylists may make claims about no slide, this one actually delivers. Want more strength? To get a 15% boost, just press turbo. Additionally, this haircut clipper’s DC motor offers 50% more cutting power to handle even the most difficult hair.
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, especially when children are present, basic safety pre-cautions should always be followed, including the following:
Read all instructions before using.
Keep away from water.
DANGER — any appliance is electrically live, even when the switch is off.
To reduce the risk of death or injury by electric shock:
- Unplug this appliance before cleaning.
- Do not place or store appliance where it can fall or be pulled into a tub or sink.
- Do not use while bathing or in a shower.
- Do not place in, or drop into, water or other liquid.
- Do not reach for an appliance that has fallen into water. Unplug immediately.
- Always unplug this appliance from electrical outlet immediately after using.
DO NOT REACH INTO THE WATER
WARNING — To reduce risk of burns, electrocution, fire, or injury to persons:
- This appliance should never be left unattended when plugged in. Do not pull, twist, or wrap line cord around appliance.
- This appliance should not be used by, on, or near children or individuals with certain disabilities.
- Use this appliance only for its intended purpose as described in this manual. Do not use attachments not recommended by the manufacturer. Do not use an extension cord to operate this appliance.
- Never operate appliance if it has a damaged cord or plug, or if it is not working properly, if it has been dropped or damaged, or dropped into water. Return appliance to a service center for examination and repair.
- Keep cord away from heated surfaces.
- Never drop or insert any object into any opening on this appliance.
- Do not place appliance on any surface while it is operating.
- Do not use this appliance with a damaged or broken comb or with teeth missing from the blades, as injury may occur. Before use, make certain blades are aligned properly. (See “Care of your Clippers.”)
- Do not operate outdoors or where aerosol (spray) products are being used or oxygen is being administered.
- Never operate the appliance with the air openings blocked or while on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, and the like.
- Always attach plug to appliance first, then to outlet. To disconnect, turn all controls to “OFF”; remove plug from outlet.
- Avoid skin contact with moving blades.
- Always check for tangles or kinks in the cord. If the cord does become tangled during use, turn unit off and straighten cord before operating.
SAVE THESE INSTRUCTIONS
OPERATING INSTRUCTIONS
This appliance is intended for household use. Use on Alternating Current (120V AC 60Hz) only. This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in the outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
Your new Conair Haircut and Trimmer Kit has everything you need to achieve professional hair-cuts, beard trimming and detailing at home. Its powerful new torque motor clipper, with steel blades for long-lasting cutting precision, features a new 5-position adjustamatic taper control. Whatever hair length you set the button for; the clipper will automatically cut all hair in that section at the desired length. Also included are 9 attachment combs for different hair lengths (including left and right ear taper combs), barber scissors, a styling comb with angled teeth, a full-length barber cape, and a soft, foldable pouch for easy storage. It also comes with lubricating oil, a cleaning brush and a blade guard for easy maintenance and protection of the clipper blades.
In addition, your kit has a full size trimmer blade with three jawline combs and one 5-position comb designed to trim facial and neck hair precisely.
THE CONAIR GUIDE
TO CUTTING HAIR AT HOME
Before you start:
- Inspect your clipper. Make sure it’s free of hair and dirt, properly oiled, and running smoothly.
- Place cape around the neck of the person getting a haircut.
- Seat the person so that his or her head is at your eye level. This gives you greater visibility and control.
- First, comb hair until it’s tangle-free. Then hold clipper in a comfortable grip. Now you’re ready to cut.
MEDIUM TO LONG CUT
To begin with, cut only a small amount of hair until you become used to the length each attachment leaves the hair. Try the longest attachment comb and put the taper control in the highest setting. If you want a shorter cut, you can then use shorter combs.
- Short attachment comb (number 1) cuts hair to 1/8″.
- Medium-Short attachment comb (number 2) cuts hair to 1/4″.
- Medium-Long attachment comb (number 3) cuts hair to 3/8″.
- Long attachment comb (number 4) cuts hair to 1/2″.
- Long attachment comb (number 5) cuts hair to 5/8″.
- Long attachment comb (number 6) cuts hair to 3/4″.
- Long attachment comb (number 7) cuts hair to 7/8″.
- Left ear attachment comb lightly tapers over left ear.
Right ear attachment comb lightly tapers over right ear. These combs make this part of the haircut easier.
Attach combs by holding them teeth up, then snapping them onto the bottom of the clip-per blade.
To remove comb attachments, place index finger and thumb as illustrated; then pull out and up.
NOTE: Never push or shove the clipper through the hair to make it move more quickly. Professional experience shows that the clipper works most efficiently when it cuts through the hair at its own speed.
To begin cutting hair:
- The hair should be combed in its natural direction.
- Using the largest attachment comb, trim sides from the bottom upward. Hold clipper lightly against the hair with teeth of the attachment comb pointing upward, yet flat against the head.
- Gradually lift the clipper upward and outward through the hair, trimming just a little at a time.
- Repeat around sides and back of head.
If you want hair to be even shorter:
- Apply more pressure to the head with the attachment comb that is in place. This takes a little practice, of course.
OR
- Just switch to a shorter attachment comb.
Remember, it’s better to leave too much hair than too little. For longer hair on top, use the barber comb and lift hair on the top of the head, cut-ting over the comb, or hold the hair between the fingers and cut to desired length. Always working from the front to the back of the head, gradually cut the hair shorter by reducing the space between the comb or fingers and the head. Comb often to check for uneven strands, and to get rid of trimmed hair.
*Equipped with a turbo switch, this unit is designed to provide 15% extra power making it easier to cut thicker, coarser hair.
OUTLINING
Outlining requires no attachments. Comb hair into the desired style. Position the clipper between the sideburns and the ear (see below), making sure the corner edge of the blade is against the hairline. With the outline of the hair as your guide, slowly move the clipper over, around and behind the ears. For the back of the neck and the sideburns, hold the clipper upside down (see above) and, holding it against the skin at the length desired, move the clipper downward.
STOP. COMB. CHECK.
For best results, do as the professionals do: comb hair often, and check clipping results as you comb. This way you avoid uneven sides, bangs, neckline, etc.
FOR ULTRA-CLOSE FADE STYLES:
A fade cut is a haircut that starts with very short hair (almost bald) on the sides of the head, but lengthens as it nears the top.
- Start with clean, dry hair. If hair is fairly long, use a long comb attachment (ideally #4) to remove the bulk of your hair before starting the fade cut.
- Using the long comb attachment, trim hair, cutting against the growth of your hair (from base of neck up towards top of head). At first, until you become familiar with the different attachments, begin with a longer one. You can always go back and make your hair a little shorter. Brush or comb away cuttings as you go. Do not force the blades through the hair. Let the trimmer do the work. Using the #1 comb attachment, you can cut hair as short as 1/8″.
- Gradually trim hair from entire head, rotating trimmer when necessary. Keep cutting against the natural growth of your hair.
- Establish the fade line. Remove comb attachments. With the taper control in position #1, start by blending the hair at the fade line by trimming up and out, repeating as you rotate around the head. Cut hair shorter on the sides and base of the head than on the top of the head.
- With the taper control in the #5 position, the blade is as close as it can be to the head. Now repeat the above process, virtually removing all hair. Begin at the base of the scalp and blend towards the fade line. The goal is to blend the hair so there is no real line, just a perfect fade from bald on the sides to very short hair on the top. Continue blending – remember to comb or brush hair against the natural growth to remove cuttings as you go until you achieve the desired look.
FOR THE BALD CUT
Follow the instructions for the FADE CUT, cut-ting hair progressively shorter with each pass of the clipper. For a bald effect, remove all comb attachments and move the taper control to the #5 position. To receive maximum closeness, overlap strokes in a crisscross pattern. To achieve a smooth bald look, we recommend you finish by using a razor with lather to shave entire head. To achieve a smooth, close shave use the Conair Hot Lather machines with your favorite shaving cream.
SHORTCUTS TO PERFECT FLAT TOPS, CREW CUTS, ETC.
Always cut from the back of the neck to the crown, using the longest comb setting. Hold the comb attachment flat against the head and slowly move the clipper up through the hair. Use the same technique for the sides, cutting from the bottom to the upper side of the head.
For the front to the crown, cut the hair against the direction in which it grows, then even it up with the sides.
For a flat top, use the flat comb, not the attachment comb. Just cut hair on top of the head over flat comb (see above).
To taper hair down to the neckline, use attachment comb #1. Comb hair and check for uneven spots. Outline sideburns and neck areas (see “Outlining”).
USER MAINTENANCE
CARE OF YOUR CLIPPERS
DETACHABLE BLADE SET
This clipper comes with a detachable blade set. To remove the blades follow these steps:
- Hold the front part of the clipper with your thumb pressing on the blade and place another hand against the blade. (see fig. 1)
- When pressing the blade forward, the blade is detached. (see fig. 2)
TO REPLACE BLADE:
- Set the Taper Control Button to lowest position “1” (see fig. 3)
- Place the blade onto the clipper body by inserting the “Blade Tongue” down below the “Lock Tap”. (see fig. 4)
- Snap the blade down into following position. The blade is now fixed onto the clipper body. (see fig. 5)
Use these instructions to switch between the clipper and beard trimmer blades and back.
SPECIAL OIL
To maintain the blades of your Conair clipper, oil them after every three or four haircuts. Gently place a few drops of oil on the teeth of the blades, using the special Conair oil included with your set. Turn the clip-per on for a minute, then turn off. This light, natural oil was formulated specifically for the Conair high speed clipper. Because it is the right oil to use, it will not slow down the blades. Never use any other product. There is no substitute for Conair oil.
Keep oil out of reach of children.
ADJUSTABLE 5 POSITION
TAPER CONTROL
Just like levers on professional clippers, the Conair taper control is positioned at the back of the unit, which functions for both the clipper and trimmer blade so you can hold the clipper in your hand and adjust the lever at the same time…while you’re clipping/trimming. This taper control eliminates the need in some situations for an attachment comb, because it lets you gradually adjust the closeness of the cut. For the closest cut and the shortest hair, push taper control up as far as it will go to level #1. To increase cutting length, slowly push control down. If you push to the lowest position level #5 or #4, it will leave hair about the same length as the short attachment comb.
Because a different cutting edge is used in each setting, the taper lever lengthens the life of your blades. Packed-in hair can slow down any clipper. To remove it without removing the blades, take your cleaning brush and brush the hair from the blades. If you do this after every clipping, especially with heavy hair cutting, the blades should remain free of cut hair. If clipper stops cutting and this action doesn’t help, try loosening the blades to remove the hair.
Any other servicing should be performed by an authorized service representative. The appliance has no user serviceable parts. The product is for household use. (see note).
If clipper stops cutting, check to see if there is a clump of hair lodged between the blades. If that is the problem, unplug the clipper and then loosen the blades to remove the hair.
If the clipper stops cutting but does not stop running, you will need to check the blades. For new blades, send check or money order for $6.50 which includes postage and handling to:
CONAIR CORPORATION
150 Milford Rd.
East Windsor, NJ 08520
NOTE:
Never pull on the clipper cord. Never twist or wrap the cord around the clipper. To store your clipper, lay it flat with the cord coiled up, then place in cylinder.
FRONT VIEW
Frequently Asked Questions
Is this a rechargeable or corded?****
Corded.
Can it be used cordless?****
NO! Don’t be fooled by the photo in their marketing materials. It needs to be plugged in when using it. It has NO battery. If you’re using this to cut your hair VERY short, don’t get it. It does not have a 0.5 level attachment. The shortest attachment is 1.0
Does this clipper set work well for doing fades?****
I use it for fades and it works well.
Is this a 220v trimmer that can be used outside the US !!****
I use it outside the U.S. with a 220 to 110 converter.
Can I shave my chest with this?****
Yes you can shave everywhere. There are plenty of comb attachments; if you don’t want to clip to the skin surface.
How long is the cord for this? Looking for a trimmer with and 8ft cord due to outlet locations, and have been unhappy with rechargeables.****
Definitely not 8ft cord.
Does this include clippers AND a trimmer?****
This has the main hair clippers but does not have a second trimmer.
can it trim back hair?****
Yes, it can.
Is Conair made in China? Will not buy China items.****
The Conair Chopper Complete 24piece Grooming System is made in China.
Does this clipper have hair length settings without attaching the comb attachments? I used to have a similar looking clipper with 3 length settings****
Yes, it does. When I adjust it this way though, it seems to pull my hair rather than clip it.
what are the lengths of the combs?****
1/8” 1/4” 3/8” 1/2” 5/8” 3/4” 7/8” 1”.
Does this come with a case to keep everything in?****
yes this model does come with case and everything complete for home use.
Is this rechargeable, if so does it come with charger?****
If I remember right,,,, this is NOT rechargeable it is actually electric but the pic does not show the cord.
I have used this clipper for the past 4 yrs. and love it to shave my husband. Where can I purchase blades for it?****
You can purchase it on amazon.
Where is this made?****
In the USA.
Video
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>