HINKLEY 5536BZ LED Spot Light Instructions

5536BZ LED Spot Light Instructions

5536BZ LED Spot Light

Start here
The fixture can be installed to ground by using appropriate 120V rated burial post , also can be installed to junction box using cover instructions listed below

| |
---|---|---

1. Install lumacore engine to enclosure, twist engine to lock into place -Drawing 3
2. Place guard over lumacore engine -Drawing 2
3. Make sure junction box power is off
4. Slip fixture wires through hole in the center junction box of cover (2) and make wiring connections between junction box (1) and fixture (4). Refer to IS-18 on the second page
5. Secure junction box cover (2) and gasket to junction box (1) using screws (3)
6. Thread conduit nut (6) onto fixture (4)
7. Next thread on fixture (4) to junction box Use conduit nut to tighten fixture (4) into place
8. Fixture can now be powered on

I.S. 18 wiring grounding instructions

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (IS 18) AND ANY ADDITIONAL DIRECTIONS.
TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS

wiring instructions
Indoor Fixtures

1. Connect positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to positive fixture lead (B) with appropriately sized twist on connector – see Drawings 1 or 2.
2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
3. Please refer to the grounding instructions below to complete all electrical connections

Outdoor Fixtures

| |
---|---|---

1. Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conductor cord) to positive fixture lead (B) with appropriately sized twist on connector – – – see Drawings 2 or 3.

2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).

3. Cover open end of connectors with silicone sealant to form a watertight seal.
   If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a fixture mounting platform specially.

4. Please refer to the grounding instructions below to complete all electrical connections.

grounding instructions
Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture ground wire (E) (typically copper or green plastic coated) to the fixture mounting strap (M) with the ground screw (S) – see Drawing 1.
Note: On straps for screw supported fixtures, first install the two mounting screws in strap. Any remaining tapped hole may be used for the ground screw.
Chain HungFixtures
Loop fixture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (S) on fixture mounting strap (M) and connect to the loose end of the fixture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Drawing 2.
Post-Mount Fixtures
Connect fixture ground wire (E) (typically copper or green plastic coated) to power supply ground with appropriately sized twist-on connector inside post. Cover open end of connector with silicone sealant to form a watertight seal – see Drawing 3.

Assembly Instructions

Item No: 30G4SE-120V and 27G4SE-120
Start here

| |
---|---|---

1. In order to lamp the fixture you need to first assemble the engine.

2. Take the optic (O) and push it into the top of the engine (E) and twist it into place – see Drawing 1.
   Note: Engine optic (O) comes in 3 types.

3. Hold the Lumacore with the Hinkley Logo so that its readable. The rotational switch (A) can be adjusted by your fingers or a small flat bladed screwdriver.
   Rotate until the switch falls into a stop. For reference, the wattage settings are roughly akin to hours on a standard clock face. -See Drawing 2

4. After the engine is assembled, you can lamp the fixture by pushing the engine into place inside the enclosure.

5. Finish by reassembling the fixture – See Drawing 3

OUTPUT SWITCH SETTINGS

| 3 Watts, 3.2 VA, 260 Lumens
---|---
| 5 Watts, 5.3 VA, 350 Lumens
|  8 Watts, 7.8 VA, 475 Lumens
|  12 Watts, 12.4 VA, 750 Lumens

Black – Flood, 60°
White – Spot, 20°
Grey – Medium Spread, 40°

HINKLEY 33000 Pin Oak Parkway, Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkley.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>