KILOVIEW MG300 IP Video Media Gateway User Guide
- June 5, 2024
- KILOVIEW
Table of Contents
KILOVIEW MG300 IP Video Media Gateway User Guide
Device Interfaces
- ) Device reset button, press and hold for 5s to restore the device to factory settings.
- 100M/1000M Ethernet port
- 100M/1000M Ethernet port
- HDMI output
- SDI output
- 3.5mm line in/o
Device Installation
Card Installation
Align the card assembly with the card slots and push in parallel, then tighten
the double-sided screws.
Device Connection
Note: Please use the standard power adapter to power the device. Other unqualified power supplies may damage the device.
Login to the device webpage
Login to the device webpage via the default IP address 192.168.1.168. That is,
enter http://192.168.1.168/ in the browser to access the web UI. The
username and the password are admin by default.
If using the device for the first time, please configure the device IP address
based on your working network.
Introduction
- To login with the default address, make sure that the computer is configured under the same network segment (192.168.1., refers to numbers between 1-255 except 168)!
- After change the device IP, please restore the computer network to the working network IP address.
- If the RMG-300 device is connected to the network by Ethernet port 2, the default IP address is: 192.168.2.168!
- To ensure information security, it is recommended to change your password immediately after your first login.
- Due to the browser compatibility issues, it is recommended to use Chrome, Firefox or Edge.
For more information about the configurations, please refer to:
https://www.kiloview.com/en/support/docs/RMG-300/
Decoding and Output
Add video source
In the lower left of the “Media”, click “Add”, and then select the “Source
Type” and configure the parameters in the pop-up dialog box, and click “OK” to
add the video source to the video list.
Introduction
- The IP address of video source can be tested with a player such as VLC.
- For video sources from the network, the playback buffer needs to be configured with a high buffer time until the video decoding output is smoot
For more information about how to add the video source to RMG-300, please
refer to:
https://www.kiloview.com/en/support/docs/RMG-300/
Preview
The added sources will be displayed in the “Video Source”, drag the source to
the upper “Source Preview” window to preview the source images and to
configure the output parameters.
Introduction
- It is recommended to use the latest version of Chrome and Edge for preview function.
- Preview in browser does not support video sources with B-frame and H.265.
- To preview, please use the service network IP address to login to the device.
- The “Source Preview” window is under “Image” mode by default, and the image refreshes every 3 seconds; if the CPU performance of the computer is well, you can click and switch to “Video” mode, and there will be smooth video.
Output
There are two output windows on the RMG-300 webpage. You can select SDI or
HDMI to decode and output the same or different content in the upper right
corner of the window. Drag the video source into the output window, that is,
output with the selected SDI or HDMI interface.
Introduction
- The output resolution should be the resolution and frame rate that the receiving monitor can support.
- The audio is turned off by default, and it can be turned on by click the red speaker in the lower left corner of the output window.
- Multi-screen output needs to be configured by adding a layout, and supports up to 9 grids output
For more info about RMG-300 output layout configurations, please refer to:
https://www.kiloview.com/en/support/docs/RMG-300/
Stream service
Login to the MG300 webpage, click “Stream Service”- “Add Publishing Points” to add a publishing point, and select the video source that needs to be forwarded.
-
Click “Source” and select the video source in the source list on the right, then the border of the selected video source will turn to red.
-
Click “Service”- “Add Stream Service”, and then choose the “Service Type”.
For more information about the RMG-300 streaming service:
https://www.kiloview.com/en/support/docs/RMG-300/
Firmware Upgrading
Download upgrade firmware
Kiloview will continue to provide the firmware of updating functions and
fixing bug for RMG-300, please refer to:
https://www.kiloview.com/en/support/download/
Select “video decoders” > “RMG-300”, find and download the latest firmware
Upgrade device firmware
Login to the web page of RMG-300, click “Settings”– “Firmware Upgrade” to check whether the latest firmware version downloaded is higher than your current version. If yes, select the downloaded firmware and click “Firmware Upgrade”.
After uploaded the firmware successfully, it needs to reboot the device. After
clicking “ok”, the device will restart, please be patient.
Note
- Please not power off during the upgrade process, otherwise the device couldn’t work.
- Generally, it will take 3-5 minutes to upgrade the device. If it’s still not completed after 5 minutes, please try refreshing webpage, if you still can’t access it, please try to contact technical support.
Restore factory settings
If the device cannot work normally after modified the parameters or forgot
internet IP configuration and couldn’t search and find the device, please
restore factory settings.
Two methods for restoring factory settings:
- If you can login to web page, then via the WEB page, click “Settings—System settings–Restore factory settings”.
- If you can’t login to web page, press the RESET button for 5 seconds in the bottom of device.。
Note: After restoring factory setting, below parameters will be turned to
default value:
- Login user name and password will be “admin”;
- IP address will be restored as 192.168.1.168, subnet mask will be 255.255.255.0;
- All encoding parameters of video and audio will be restored to default value.
Others
To prolong the device life, please unplug the power and keep it properly if you do not use it for a long time.
For more questions, please contact us via：
https://www.kiloview.com/en/support
KILOVIEW Electronics CO., LTD.
Tel: 86-18573192787
Email: support@kiloview.com
Web: www.kiloview.com/en
Address: B4-106/109, Jiahua Intelligence Valley Industrial Park, 877
Huijin Road, Yuhua District, Changsha City, Hunan Province, China.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>