bittel HWD9888 Cordless Telephone Phone User Manual

: June 5, 2024
: Bittel

Table of Contents

bittel HWD9888 Cordless Telephone Phone
Product overview
Installation
Location and Control
WEB interface function description
**Upgrade
Main Menu
Basic Operation of Phone
Simple failure diagnosis and troubleshooting
FCC Warning
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

bittel HWD9888 Cordless Telephone Phone

Product overview

HWD9888(62)TSD IP is 1 line SIP cordless phone, which is specially designed for top grade hotels’ telecommunication. It has clear sound, stable quality, powerful function and elegant design, etc. It s also a kind of SIP phone which transmits voice over network based on IP pro tocol.

Main Features

The Base and Handset can make/answer any calls freely. One Base can work with 1 4 Handsets.
Supports SIP V2/SDP/RTP/RTCP/STUN/SNTP/ DNS/SNMPv2 protocols.
Support s IEEE802.1 Q standard, IEEE802.3af protocols.
Supports G. 711/G.722(HD Voice)/G.723/G.729AB /G.726/iLBC
Support 1.8/1.9Ghz, DECT6.0 and adopts HF numerical coding technical between Base and Handsets.
Mute, hold, flash, redial and Speaker feature
Message waiting light compatible with main PBX, MWL indicat or and withdraw feature
Owns ten (10 ) service keys
Both Base volume and Handset volume are in five level control
Supports DHCP and static IP address protocol for getting IP address.
Support upgrade through HTTP/TFTP protocol.
Adopts d ynamic speech detection; Comfortable noise generation; Speech buffering technologies.
Integrated PoE power supply and external POE adapter power supply.
For HWD9888(62)TSD IP ,O ne of the handset is corded

Installation

Please p ut the attached cha rgeable batteries into the handset, pay more attention to the polarity of socket and signal ribbon cable, also need to notice the direction of the jack and the socket during install the batteries. Strictly prohibit to use the wrong polarity batteries.
For HWD9888(62)TSD IP , please connect the phone handset cord
Power by POE: Connect the output end to the WAN port of the phone and connect the input end to the Internet cable from hotel edge switch POE port.
Power by adaptor (The default is Please c on nect the 9V power adapter to the DC power input, which is in the rear of the phone; connect the Internet cable to WAN port of the phone, and connect the Internet cable to the LAN port of Data port/access point.
Please i nstall the phone in dry and clean environment and avoid effected with damp. 6. The telephone should avoid fire, water spray, shock, clean the surface dust by soft cloth; chemical solvent is prohibited to use.

Location and Control

bittel HWD9888 Cordless Telephone Phone
1

1.Service Keys	2.Function Keys	3.Number Keys
4. DC Jack	5. WAN Port	6.LAN Port
7. Message Waiting Light	8. Handset Jack	9. TO TEL Port

Configure the phone through WEB Interface

IP address broadcast Off-hook status, continually press * button four times will enter the voice menu. Press 1 (network setting) then press 2 (WAN port IP address), the obtained IP address will be broadcast.
WEB interface Input the obtained IP address to launch WEB interface . Type in user and password to log in WEB interface. 3. Launch WEB interface Input the obtained IP address to launch WEB interface . Type in user and password to log in WEB interface.

Launch WEB interface

Input the obtained IP address to launch WEB interface Type in user and password to log in WEB interface. bittel HWD9888 Cordless Telephone Phone
6

Note:

Both the user name and password in initial management mode are ‘admin’.
The defa ult network mode is DHCP. Once the phone is connected into the network environment with DHCP service, it can get online automatically

WEB interface function description

Phone status

Product

Information

| It shows the basic information of the product.
---|---
Line Status| It shows the registration state of each line.
Network Status| It shows the information of Internet Port WIFI

and PC port.

Wireless Info| It shows the current WIFI setting and status.
System Status| It shows the current time and the running time

of the product.

Network status
Telephone can obtain IP address from DHCP server in default mode. Enter WEB interface to configure all related settings in accordance with real network environment.

WAN IP Mode| Select WAN port IP address obtainment

modes including static/ DHCP/ PPPoE/ Bridge.

---|---
MAC Address

Clone

| Enable MAC address clone or not
NAT Enable| Activate NAT function or not.
VLAN Mode| Activate VLAN mode or not
VLAN ID| Set VLAN ID

DNS Mode

| If DNS mode is Manual, user needs to set primary DNS and secondary DNS manually. If DNS mode is Auto, IP phone will obtain primary DNS and secondary DNS from DHCP

server automatically.

Primary DNS| The Primary DNS setting
Secondary DNS| The optional DNS setting
IP Address| The network port IP address
Subnet Mask| The network port subnet mask
Default

Gateway

| The network port default gateway

Note:

When telephone IP address is switched from DHCP to static mode, all parameters such as IP address, Subnet Mask, Default Gateway and DNS need to be set manual ly.
Save and apply switched IP address settings and reboot the phone for new IP address obtainment. Make sure the network is normal during daily using. 4 .

SIP Account Setting

Phone regular usage ,only need to configure Proxy Server, Display Name , Phone Number, Account, Password.

Administration
Client can set password, languages, restore factory defaults

**Upgrade

bittel HWD9888 Cordless Telephone Phone
7 **

Local Upgrade

| Click “Browse” to select certain firmware, click Upgrade button for upgrading. After upgrade,

phone will return to initial interface.

---|---

WEB Operation

Except regul ar configuration, please do not modify other corresponding information.

Voice Menu Instruction

The phone has voice menu function; relevant information can be configured through voice menu. After starting the phone, press 4 times the * key to enter the v oice menu. Hanging off can exit the voice menu.

Network

Configuration

| After choosing key 1, the phone will enter Submenu

1.1 network configuration setting.

---|---
Telephone port

configuration

| After choosing key 2, the phone will enter Submenu

2.1 phone port configuration setting.

Factory Reset| After choosing key 3, enter the password; the phone will then return to factory setting.
Speed Dial configuration| After choosing key 4, enter speed-dial configuration

option; enter speed-dial key, then enter the speed-dial number to complete the configuration.

Reboot

| After choosing key 5, enter password; the phone will

then reboot.

WAN Port Login

| After choosing key 6, enter password to set up whether WAN port can allow logging.

WEB Access Port

| After choosing key 7, enter password to set up Web access port.
Software

Version

| After choosing key 8, current software version will be

broadcast.

Submenu 1.1

Wan port

connection type

| After choosing key 1, the phone will broadcast

current Wan port connection type; after entering password, DHCP or static IP address can be set up.

---|---
Wan port IP address| After choosing key 2, the phone will broadcast

current IP address; after the broadcast is finished, IP address can be set up.

Wan port subnet mask| After choosing key 3, the phone will broadcast

current subnet mask; after the broadcast is finished, subnet mask can be set up.

---|---
Gateway| After choosing key 4, the phone will broadcast

current gateway; after the broadcast is finished, gateway can be set up.

DNS| After choosing key 5, the phone will broadcast

current DNS; after the broadcast is finished, DNS can be set up.

Submenu 2.1

Telephone number| After choosing key 1, the phone will broadcast

current phone number.

---|---
Server IP address| After choosing key 2, the phone will broadcast

current server IP address.

Physical port| After choosing key 3, the phone will broadcast

current physical port.

Call transfer

configuration

| After choosing key 4, call transfer option can

be set up.

Volume control

mode

| After choosing key 5, volume control mode

can be selected.

Redial timing| After choosing key 6, whether redialing

number will be removed after a fixed time can be set up.

Ringing voice

adjusting mode

| After choosing key 7, whether ringing volume

adjustment is allowed can be set up.

Speed-dial button

and voice mail configuration

| After choosing key 8, speed-dial button can be

configured.

Note :

When using voice menu configuration to achieve relevant operation, please reboot the phone.
After entering password, IP address or other number, please enter # to confirm.
When using keyboard to enter password,
- Press number key 2 if A, B, C, a, b, c is to be entered.
- Press number key 3 if D, E, F, d, e, f is to be entered.
- Press number key 4 if G, H, I, g, h, i is to be entered.
- Press number key 5 if J, K, L, j, k, l is to be entered.
- Press number key 6 if M, N, O, m, n, o is to be entered.
- Press number key 7 if P, Q, R, S, p, q, r, s is to be entered.
- Press number key 8 if T, U, V, t, u, v is to be entered.
- Press number key 9 if W, X, Y, Z, w, x, y, z is to be entered.
- When using the keyboard to enter the password, other characters can be replaced by number key 0.
- When entering IP address, use “” to replace “.”; for example, if the IP address is 192.168.10.100，enter 19216810100 instead.
Press key one time to return to the menu; press key twice to return to the menu if in IP address entering status.
Hanging off the phone can exit the voice menu.

Basic Operation of Phone

T o register the Handset
On hook status, press HOLD+*+HOLD+MUTE of the base ( the indicator of SPKR, MUTE and HOLD will flash),
Press HOLD+*+HOLD+MUTE of the cordless handset,
After 5 8s, press REDIAL/PG key of the base.
The handset will ring, whi ch means successful.
- Off hook Press ON or SPKR of the handset or press SPKR button of the base.
On hook
- Put the handset back to the base or press SPKR again
- Please press OFF key of the handset or put the Handset back to the charging base
- Press SPKR button again if it’s in speaker mode.
Service Button
- Off hook mode, press certain service key to dial the number directly.
- How to Store: Keep the base in on hook mode, press HOLD+ Desired number + Service key / MWL There will be indicating tone if succeed. For the handset, in on hook mode, press HOLD + +HOLD+N+M of the base (N=1,2 or 3, which stands for the location of the service button of the handset; M stands for the service button of base) . For example, if yo u want to program the 2 nd service button of the handset and the desired number is same as the 7 th service button of the base, the solution is: On hook status, press HOLD + +HOLD+N+M of the base, then press 2 and press the 7 th service button of the base.
- How to delete: On hook mode, press HOLD+HOLD+ service key / MWL key of the base. Please make sure that there is power.
Using the hold key Press HOLD key, the indicator will turn on, the current line is held, press HOLD key again or press O N/ SPKR of the handset or press SPKR of the base can release the hold mode.
Mute Off hook mode, press MUTE key once to stop the sending, press it again to remove the mute mode (Base with LED indicator). 7. Adjust the call volume
- Press VOL+ or VOL of the base to adjust the volume. Total are five levels.
- Press VOL+ or VOL of the handset to adjust the volume. Total are five levels.
To redial the last number dialed and Call the handset
- Off hook, press REDIAL key of the base or the hand set to dial the last number dialed.

Default mode

After on hook, the last dialed number will disappear automatically within five minutes.

MWL Message Waiting Light

When there is new message, the MWL will flash, press MWL key can retrieve the message

Handset call and speaker call and cordless handset call’s inter converting

From handset call to Speaker call:
- Press SPKR key, then put the handset back
From Speaker call to Handset call:
- Press SPKR of the handset again.
From Handset to Base:
- When Handset is calling, press SPKR of the base, then press OFF k ey of the handset.
From Base to Handset:
- When Base is speaker mode, press SPKR of the handset and press SPKR of the base, it will enter handset speaker mode. If you press ON key of the handset and press SPKR of the base again, it will enter hand set Non speaker mode.

Restore Factory

When the phone is powered on, after boots up successfully, press 3 when enter the voice menu, enter the phone password + # Key to restore factory, after all finished please reboot the phone.

POE power supply instructions

The phone can view the POE power supply level by managing the POE switch. If powering the sound or charging stand, the power level is 0 or 6 and the maximum value is 12.95W; If only powering a phone, the power level is 2 and the maximum value is 6.49 The power level of this type is 2

Simple failure diagnosis and troubleshooting

Faults	Solution
The phone doesn’t work	1. Please check whether the telephone power supply is

connected properly

2. Check whether the switch port supports POE power supply

3. Check whether the Ethernet cable is plugged correctly.

The phone can’t get IP| 1. Please check whether the way get IP is correct

2. Please check the network

3. Please check the network VLAN settings

Unable to login the

WEB interface

| Check whether the computer and the phone

are on the same network

The radio has

noise or no signal

| Please confirm whether there is a

corresponding radio program in this band

Speaker has no sound| 1. Please check whether the device is connected to the power supply

2. Adjust the sound volume, increase the volume

Phone works abnormally| Please power off the phone and turn on the

electricity, check whether it is working properly after one minute

WARRANTY

This product is warranted for a period of 12 months from the date of pur chase against faulty materials or workmanship. If during this period a defect arises, we may repair or replace the product, at Bittel’s discretion, provided that:

The product has not been used for any purpose other than normal use,
Unauthorized prod
Unauthorized product repair or modifications have not been uct repair or modifications have not been attempted.attempted.
The product has never been used in a harsh or corrosive
The product has never been used in a harsh or corrosive environment.environment.
No damage in transit
No damage in transit

THIS LIMITED WARRANTY GIVES THE BUYER SPECIFIC LEGAL THIS LIMITED WARRANTY GIVES THE BUYER SPECIFIC LEGAL RIGHTS. THE BUYER MAY ALSO HAVE OTHER RIGHTS WHICH RIGHTS. THE BUYER MAY ALSO HAVE OTHER RIGHTS WHICH VAVARY FROM JURISDICTION TO JURISDICTION.RY FROM JURISDICTION TO JURISDICTION. This warranty is only valid for merchandise purchased directly from This warranty is only valid for merchandise purchased directly from Bittel or dealers or distributors Bittel Co. authorized. Bittel or dealers or distributors Bittel Co. authorized.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: –

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC radiation exposure

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

CONTACT BITTEL