CAT 25006 Mining Truck Instruction Manual

: June 5, 2024
: CAT

Table of Contents

CAT 25006 Mining Truck
Contents
Battery Precaution
Battery Installation
How To Play
Performance Tips
FCC label compliance statement:
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CAT 25006 Mining Truck

CAT-25006-Mining-Truck-
product

Battery Precaution

Alkaline batteries are recommended to be used
Only batteries of the same or equivalent type as recommended are to be used
Do not mix alkaline, standard or rechargeable batteries
Do not mix old and new batteries or different type of batteries
Non-rechargeable batteries are not to be charged
Rechargeable batteries for adult charging only
Rechargeable batteries are to be removed from the product before they are charged
Be sure to insert batteries with correct polarities and always follow the battery manufacturer’s instructions
Remove all batteries from the Vehicle and Transmitter when not in use
Exhausted batteries are to be removed from the product
The supply terminals are not to be short-circuited
Dispose of batteries properly. Do not dispose the batteries in fire- it may cause them to explode or leak causing injury or damage
Battery installation and removal must only be done by adult

Battery Installation

For Vehicle (Fig. 1 and Fig. 2)

Switch OFF the power
Unscrew the screw on the battery cover
Open the battery cover
Install 5 new 1.5V AA batteries with correct polarities (+1-) as shown inside the battery compartment
Close the battery cover
Tighten the screw on the battery cover

For Transmitter (Fig. 3 and Fig. 4)

Unscrew the screw on the battery cover
Open the battery cover
Install 2 new 1.5V “AAA” batteries with correct polarities (+/-) as shown inside the battery compartment
Close the battery cover
Tighten the screw on the battery cover

How to Bind

Turn on the Vehicle.
Install batteries in the Transmitter then the Transmitter signal light will flash for a few seconds.
After the wheels of the Vehicle turn left and right and the LED light of the Transmitter stops flashing, the binding process completed for playing.
If it cannot complete within 8 seconds, please turn off the Vehicle and re-start the binding process.
When the binding process is done, whenever switching the Vehicle on and off, it searches for the code that it memorized and will only lock on to the Transmitter signal containing that code.
Please turn off the Vehicle and re-start all binding process if changing to another 2.4GHz Transmitter for playing.

How To Play

Switch ON the Vehicle
Use the Left / Right joystick to control the Vehicle turning left or right
Use the Forward / Backward joystick to drive the Vehicle Forward, Stop and Backward
Press the Dump bed move up
Press the Dump bed move Down
if the Vehicle does not run in straight line, adjust the direction adjustment on the Vehicle chassis (Fig. 1).
Play on smooth surface for optimum performance
Remember to switch OFF the power of the Vehicle after playing.
The optimum control range is up to 25m (82ft) outdoor.

Performance Tips

Do not drive on grass, dirt, sand, dusts, carpet or go through water.
Do not drive in windy or rainy weather.
Avoid direct impact the Vehicle with obstacles.
Switch OFF the power when not in use to prevent damage of Vehicle and Transmitter due to leakage of electrolyte from batteries.
Remove all batteries from the Vehicle and Transmitter when not in use for long period.
Keep fingers, hair and loose clothing away from wheels.
The operating range can be affected by a variety of factors
Low Voltage of batteries in Transmitter or Vehicle.
Interference from other items that emit radio frequency signals.
Outdoor usage is recommended in order to get optimum control range.
Recommend to play the vehicle on a clean and smooth surface.
Clean the battery compartment to make sure it is free from dust to prevent poor contact of batteries.

Cautions

Do not attempt to disassemble the Vehicle or Transmitter.
Make sure the batteries are installed with correct polarities (+/-) as shown inside the battery compartment.
Remove the package and take out all accessories before giving the Vehicle and
Transmitter to child to play. The packaging and instruction manual contain important information. Please keep them for future reference.

Warning

Choking Hazard. Not suitable for children under the age of 3 years due to small parts.
We reserve the right to improve/amend specifications and colors without notice.
The Antenna of vehicle and/or transmitter is/are not to be inserted into socket outlets.

FCC label compliance statement:

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not ocCur in a particular installation. f this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

RSS-210 Compliance Statenment

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:

This device may not cause interference
This device must accept any interference, including interference that may cause undesired operation of the device.

Declaration of Conformity

The product is in conformity with the requirement of EU Directive 2014/53/EU

Environmental notes

The whole product also does not belong to household waste at the end of the product life. You can return it at collection points for the recycling of electronic and electronical instruments The symbol on the item, instruction manual, hangtag or packing is showing this clearly., Materials should be recycled according to their respective markings. Recycling of old devices or other re-use of materials contained therein represents an important contribution to environmental protection. Please ask at your local community for the correct collection point.

Disposal of batteries

Batteries should not be disposed of in the household waste. As the consumer you are legally obliged to return bateries containing harmful substances and all other used batteries. You can hand in your old batteries at public collection points in your area or wherever batteries are sold. You will find these chemical abbreviations along with a crossed-out refuse bin on batteries Containing harmful Substances

Pb=Battery contains lead
Cd=Battery contains cadmium
Hg=Battery contains mercury

PRODUCT MUST BE ASSEMBLED BY ADULT ONLY

Conforms to the safety requirements of ASTM F963
Frequency band: 2405-2475 MHz
Maximum radio frequency power transmitted: <0 dBm
www.cat.com/www.caterpillar.com

2020 Caterpillar. CAT CATERPILLAR, their respective logos, “Caterpillar Yllow” the “Power Edge” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.

Diecast Masters tompany Limited, a licensee of Laterpilar Inc