BBS PRO SOUND U666CGS Wireless Microphone User Manual

PRO SOUND U666CGS Wireless Microphone
User Manual

IMPORTANT SAFETY INSTRUCTIONS

1. Keep this instruction manual.
2. Heed all warnings and follow all instructions in this instruction manual.
3. Only clean the products when they are not connected to the mains and use a dry cloth for cleaning.
4. Do not expose the device to any high temperatures, dripping or splashing water, strong vibrations, or heavy mechanical stress.
5. Do not place any open sources of fire, such as burning candles, on or directly next to the device.
6. Consult an expert if you are unsure as to the function, safety, or connection of the product.
7. Never operate the device unattended.
8. Only operate the device in moderate climates, never in tropical climates.
9. Do not leave any packing material unattended. It may become a dangerous toy for children.
10. Comply with the safety and operating instructions of any other devices that are connected to the device and observe the additional safety instructions in the individual chapters of these instructions.
11. At industrial sites, the accident prevention regulations of the association of the industrial workers’ societies for electrical equipment and utilities must be followed.
12. If you are not sure about the correct connection or if there are any questions that are not covered by the operating instructions, do not hesitate to contact our technical support or another specialist.

Features

• Streamlined design, humanized operation interface, elegant appearance.
•  High-definition LCD screen, intuitive and clear
•  PLL dual channel locked loop design, ID code lock automatic selection.
•  The frequency response curve of acoustics is carefully adjusted and the sound is warm and transparent.
•  Adjustable power with two levels of selection.

Frequency range: 640-690MHz
Channels: 200CH
Frequency space: 250KHz
Working distance: 30M
Frequency width: 50MHz
Frequency oscillation mode: PLL
module locked loop design| S/N Ratio: ≥50dB
Carrier wave stability:±5KHz
Signal pick up: CPU-controlled selection
& pilot identification
Mute: Mute & Lock loop circuit
Display: LCD
Power supply: 12V DC, 1250mA
Output connection: 2 XLR Balanced
Socket +Unbalanced TRS6.3mm Socket| Frequency range: 640-690MHz
Channels: 200CH
Frequency space: 250KHz
Frequency width: 50MHz
Frequency oscillation mode: PLL module locked loop design
Power:≤30mW
Transmission method: CPU controlled
selection & pilot identification
Carrier wave stability：± 4KHz
Display: LCD+ color backlit
Capsule: Dynamic 2-level power: high-low

Receiver (front)

1. Power ON/OFF: after pressing this button, the information on the display will be lit up, and then can be operated.
2. LCD display: display frequency, battery content, and other information.
3. Knob: Adjust volume, frequency, and gain reduction
4. AI Scan: Search the available frequency intelligently
5. AI Set: To match the frequency between the receiver and transmitter
6. Pre-set Module: Chose the frequency module.

Receiver (back)

1. Antenna input: insert the attached antennas into this port.
2. Antenna: connect the receiver antenna, and form a V-shaped setting to pick up the best signal.
3. XLR balance output connection: to connect balanced audio equipment.
4. 6.3mm mixed output connection： the audio output connection of A and B channels are mixed.
5.  DC socket: connect to the power adapter.

Transmitter

Handheld Transmitter

1. Battery house: unscrew the bottom part and put the two batteries into the house.
2. Power ON/OFF: after the load cell, press this button, and the information display will light up, then can operate it.
3. LCD display: the display of information, display frequency, battery, etc.
4. Frequency matching window: for frequency verification between receiver and transmitter.

Transmitter Operation

1. Power ON/OFF Switch:
   A.Press it in 2 seconds to power on or off
   B. AI mode ON/OFF switch: When the microphone has been turned on, press the power on/off button, it will power off first, then keep pressing it and wait 5 seconds, and the microphone will automatically power on , and LCD will display “GS ON” or “GS OFF ”, that means the intelligent mode on or off.

2. Infrared frequency match window: Open the bottom part of the handheld and put the infrared window aimed at the receiver panel, it will pick up the frequency data.

Note:
a.Transmitter has High and Low power, but it can be selected only after the automatic frequency matched or infrared frequency is matched.
b. Intelligent control mode: If the microphone has not done any action within 3 seconds after starting the intelligent control mode, then the intelligent mute function will be started and it will be automatic mute. When the microphone last 8minutes in this state, it will be automatic power off. After starting the intelligent control function, if a microphone is not static under a power-on state, it will be woken up and can be normally operated.

Receiver Operation

1. Press power ON/OFF to open receiver
2. Press Pre-set Module (“+” “-“), it’s invalid if locked situation.When display “LOC ON” then press the two keys will change the A and B channel.The LCD display “MODULE” means the current frequency is module setting and after setting will be saved automatically.
3. Press “Enter” knob, Press A,B channel setting for unlock or lock,will display”UNLOC” or “LOC ON”.After unlock then press it into menu. Adjust the knob for selection “SET FRQ-SET RF-SET AUD”.After chose any item then press the knob to enter adjustment. When finish adjustment,press Enter for save, LCD will display” STORE”. If not have any adjustment then press Enter will be exit and LCD display “EXIT”.
4. Revolve the knob, when it is locked it’s invalid and will display “LOC ON”.After unlock: A.If not enter any adjusment menu, the knob will adjust the volume by left and right side turn. Volume range is 0-30.Finish volume adjustment system will exit this item and record the deta. B.SET FRQ: to turn the left and right sides can set frequency, after adjustment press the Enter for save and LCD will display “STORE”. C.SET RF: turn left and right for setting transmitter power. When matching the frequency, this data will be sent to transmitter and change its power. After adj ustment, press Enter for save, and LCD will display “STORE”. D.SET AUD:Turn left and right for audio gain reduction, the range is 0-4 (4dB is the maxmum).After adjustment, press Enter for save, and LCD will display “STORE”.
5. Press the AI Scan: it’s invalid when it’s locked. And LCD display “LOCK”. After unlock, press it to enter searching status. LCD will display “ SCAN ”, then touch the corresponded “Enter” can search the frequencies. If it’s in Pre-search and touch it will exit.
6. Press the AI Set: it’s invalid when it’s locked and LCD displays “LOCK”.After unlocking, press it to enter the pre-match frequency status and display “ SYNC ”. then touch the corresponding “Enter” can match the frequency to the transmitter. If it’s in Pre-match and touch it will exit.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>