COMEUP 883873 Wireless Remote Control Installation Guide

COMEUP 883873 Wireless Remote Control

Wireless Control Kit includes

1. Wireless Receiver.881103
2. Wiring Harness 1250 mm.
3. Wireless Transmitter.883822
4. Lithium Battery: 3V CR2032
5. Handsaver Strap.

Specifications

1. Transmission range: 15 ~ 27 m (50 ~ 90 ft)
2. Receiver operation voltage: 8 ~ 24 V
3.  Receiver fuse current rating: 7.5A
4. Protection: IP-66
5. Operating temperature range: -20°C ~ +70°C
6. LED indication: Green light for power on; Red light for winching; Blinking green for low battery life; Blinking red light for poor signal received

Installation Guide

Connect the wiring

1. Connect the Black and Green wires to the same color wires on the contactor and handlebar trigger switch respectively shown on the wiring diagram.
2. Slice the Red wire to the receiver fuse then connect to the positive (+) terminal of the battery.
3. Connect the Black wire to the negative (-) terminal of the battery.

Mount the Receiver

1. The receiver should be mounted in a clear and dry location.
2. Mount on a flat surface with 2 pcs of Ø7 mm mounting holes on each side of the receiver.

Operation

1. Install and replace battery.
2. Turn cover counterclockwise to open.
3. Replace new battery and put the cover back.
4. Turn cover clockwise to close.
5. Start
6. Turn on the ATV/UTV.
7. Press the Power button for 5 seconds until Green light comes on.
8. Press the Cable In or Cable Out button , then the Red light comes on
9. Stop
10. The system will be automatically shutting down the operation after a silence of operation for 5 minutes.
11. Press and hold the Power Button for 5 seconds for shutting down the operation.
12. Additional Emergency Stop Function: The power button also works as an emergency stop if the radio control is in malfunction of any reason. While the radio control is in operation (either winch in or winch out, the red light is on), once power button is pressed, the radio control will be forced to power off immediately. Winch will stop running accordingly.
13. Reset
14. Press and hold the Programming Button for 5 seconds until the Red lights up.
15. Press the Power Buttons for 5 seconds until the Green lights up.
16. Press the Cable In or Out button until the Red lights on the receiver turns off.
17. Reset is now completed. Please note only one remote can be reset for each receiver.
18. Notes
19. The wireless remote control and handlebar rocker switch can be exchanged for activating the winch, but it takes about 10 seconds for exchanging。
20. Blinking Green LED light shows batter low, the battery should be replaced immediately.
21. Please note only one remote can be reset for each receiver.
22. Blinking Red LED for poor signal.

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

RF exposure warning
The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>