Volcano G21 Gas patio heater Instruction Manual

G21 Gas patio heater
Instruction Manual

Thank you for purchasing our product.
Before using this unit, please read this manual.

Parts and specifications

Warning

1. If you smell gas:
   • Shut off the gas supply to the appliance.
   • If you still smell gas, immediately call your gas supplier or the fire department.

2. Do not store gasoline or any other flammable vapors/liquids near this appliance.

3. Designed for use outdoors or in amply ventilated areas (minimum of 25 % of the surface area open – one open wall).

4. Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage. Read the manual thoroughly before installing or using this appliance.

5. This appliance must be installed and stored in accordance with the regulations in force.

6. Do not cover the ventilation holes of the cylinder housing.

7. Do not move the appliance when in use.

8. Shut off the valve of the gas cylinder or the regulator before moving the appliance.

9. The gas tube must be changed within the prescribed intervals.

10. Use only the type of gas and the type of cylinder specified by the manufacturer.

11. The gas tank used with this patio heater must meet the following requirements: 11-13 kg.

12. In case of a strong wind blowing, attention must be taken to tilting the appliance.

13. The injector in this appliance is not removable and is assembled by the manufacturer only. It is forbidden to convert from one gas pressure to another.

14. Do not connect the gas cylinder directly to the appliance without the regulator. Use only the gas type and gas cylinder type specified in this manual.
    • Use a 30mbar regulator for butane/propane under the category I3B/P(30).
    • Use 30mbar regulator for butane under the category I3+(28-30/37).
    • Use 30mbar regulator for butane under the category I3+(28-30/37).
    • Use 50mbar regulator for butane/propane under the category I3B/P(50).

Safety instructions

1. Do not use the patio heater indoors, as it may cause personal injury or property damage.

2. This outdoor heater is not intended to be installed on recreational vehicles and/or boats.

3. Improper installation, adjustment, and alteration can cause personal injury or property damage.

4. Do not attempt to alter the unit in any manner.

5. Never replace or substitute the regulator with any regulator other than the factory-suggested replacement.

6. Do not store or use gasoline or other flammable vapors or liquids in the heater unit.

7. The whole gas system, hose, regulator, pilot, or burner should be inspected for leaks or damage before use, and at least annually by a qualified service person.

8. All leak tests should be done with a soap solution. Never use an open flame to check for leaks. Do not use the heater until all connections have been leak tested.

9. Turn off the gas valve immediately if the smell of gas is detected. Turn Cylinder Valve OFF. If the leak is at the Hose/Regulator connection: tighten the connection and perform another leak test. If bubbles continue appearing should be returned to the hose’s place of purchase. If the leak is at Regulator/Cylinder Valve connection: disconnect, reconnect, and perform another leak check. If you continue to see bubbles after several attempts, the cylinder valve is defective and should be returned to the cylinder’s place of purchase.

10. Do not transport the heater while it’s operating.

11. Do not move the heater after it has been turned off until the temperature has cooled down.

12. Do not paint the radiant screen, control panel, or top canopy reflector.

13. The control compartment, burner, and circulation air passageways of the heater must be kept clean.

14. Frequent cleaning may be required as necessary.

15. The LP tank should be turned off when the heater is not in use.

16. Check the heater immediately if any of the following occurs:
    • The heater does not reach temperature.
    • The burner makes a popping noise during use (a slight noise is normal when the burner is extinguished).
    • Smell of gas in conjunction with extreme yellow tipping of the burner flames.

17. The LP regulator/hose assembly must be located out of pathways where people may trip over it or in an area where the hose will not be subject to accidental damage.

18. Any guard or other protective device removed for servicing the heater must be replaced before operating the heater.

19. Adults and children should stay away from high-temperature surfaces to avoid burns or clothing ignition.

20. Children should be carefully supervised when they are in the area of the heater.

21. Clothing or other flammable materials should not be hung on the heater or placed on or near the heater.

22. To change the gas cylinder in an amply ventilated area, away from any ignition source (candle, cigarettes, other flame-producing appliances).

23. To check that the regulator seal is correctly fitted and able to fulfill its function shown in the photo right;

24. To not obstruct the ventilation holes of the cylinder housing;

25. To close the gas supply at the valve of the gas cylinder or the regulator after use;

26. In the event of gas leakage, the appliance shall not be used or if alight, the gas supply shall be shut off and the appliance shall be investigated and rectified before it is  used again;

27. To check the hose at least once per month, each time the cylinder is changed or each time before a long time no use. If it shows signs of cracking, splitting, or other  deterioration it shall be exchanged for a new hose of the same length and of the equivalent quality;

28. Read the instructions before using this appliance. The appliance must be installed in accordance with the instructions and local regulations.

29. For connection of hose and regulator and connection of regulator and hose, please refer to the photo shown below.

Heater position

The heater is primarily for outdoor use only. Always ensure that adequate fresh air ventilation is provided.
Always maintain proper clearance to combustible materials, i.e. top 100 cm and sides 100 cm minimum.
The heater must be placed on level firm ground.
Never operate the heater in an explosive atmosphere like in areas where gasoline or other flammable liquids or vapors are stored.

Gas requirements

This heater is primarily designed to be used with propane gas tanks.
Butane gas tanks may also be used with the appropriate regulator.
The installation and use of this appliance must correspond with local standards, or in the absence of local codes, with the standard for the storage and handling of liquid petroleum gases.
A dented, rusted, or damaged propane tank may be hazardous and should be checked by your tank supplier. Never use a propane tank with a damaged valve connection.
The propane tank must be arranged to provide for vapor withdrawal from the operating cylinder.
Never connect an unregulated propane tank to the heater.

Leakage test

Gas connections on the heater are leak tested at the factory prior to shipment. A complete gas tightness check must be performed at the installation site due to possible mishandling in shipment or excessive pressure being applied to the heater.

• Make a soap solution of one part liquid detergent and one part water. The soap solution can be applied with a spray bottle, brush, or rag. Soap bubbles will appear in case of a leak.

• The heater must be checked with a full cylinder.
  

• Make sure the safety control valve is in the OFF position.

• Turn the gas supply ON.

• In case of a leak, turn off the gas supply. Tighten any leaking fittings, then turn the gas supply on and recheck.

• Never leak test while smoking.

Use and storage

To turn on:
Warning: Please ensure the glass tube has not been damaged during transportation.

1. Make sure the variable control knob is in the OFF position.
2. Connect the gas regulator to a compatible gas cylinder.
3. Push and turn the variable control knob to the PILOT position and hold it for 60 seconds. Whilst still holding the control knob down, press the ignition button – a pilot flame should appear.
4. Once the blue pilot flame stays lit up constantly, let go of the variable knob.
5. Turn the variable control knob to the desired temperature position.
   • When lighting the heater on for the first time or an after a new cylinder was connected, the air inside the hose must be purged. This process will take a few minutes as liquefied petroleum gas is heavier than air.
   • To do so, press the variable control knob down in the PILOT position for about 3 minutes.

To turn off:

1. Turn the variable control knob to the PILOT position.
2. Press and turn it to the OFF position.
3. Turn the regulator connected to the gas cylinder to the OFF position.

Storage

• Always turn the regulator connected to the gas cylinder to the OFF position after each use.
• Disconnect the regulator from the cylinder if the heater is not in use.
• Never store the gas cylinder indoors or without adequate air ventilation.

Cleaning and care

• Wipe off surfaces with a soft, moist cloth. Do not clean the heater with cleaning products that are combustible or corrosive.
• Remove debris and insects from the burner periodically to keep it clean and safe for use.
• Cover the burner unit with a protective cover when the heater is not in use.

Construction and characteristics

• Transportable terrace/garden heater with cylinder housing.
• Constructed with aluminum, powder coated, and stainless steel.
• Heat is emitted upwards through the glass tube and distributed via the top reflector.

Specifications

• It is recommended to use a propane gas tank only
• Max wattage: 13 000 watts
• Min wattage: 5 000 watts
• Consumption:
• Using the proper regulator according to the outlet pressure of the regulator is explained above.
• The hose and regulator assembly must conform to local standard codes.
• The regulator outlet pressure should meet the corresponding gas category in the table of injectors.
• The appliance requires an approved hose of 1.4 m in length.

Řešení problémů

•Empty has a tank
•Air in the hose/tube
•Loose connections| •Open it
•Replace it
•Clean or replace the opening
•Control connections
The pilot doesn’t stay on| •Debris around the pilot
•Loose connections
•Bad thermocouple
•Gas leak in lines
•Low pressure| •Clean the area
•Control connections
•Replace it
•Control connections
•Tank nearly empty, refill it
Burner doesn’t work| •Low pressure
•Control knob not on
•Bad thermocouple
•Dirty gas supply opening| •Tank nearly empty, refill it
•Open it
•Replace it
•Clean it

The English version of the manual is an exact translation of the original manufacturer‘s instructions.
Images used in this manual are for illustrational purposes only and may differ from the actual product.

Installation

Parts list

Assembly
You will need:

• Screwdriver
• Spray bottle of soap solution for leakage test

Hard Wares List

Montageanleitung

1. Assemble the wheel assembly (M) and connect it to the bottom plate (N). Fix it with 4 M8x12 bolts and 4 M8 nuts.
   

2. Insert the pins of the bottom plate (N) to the holed of the lower support (L). Using 12 3/16‘ screws (DD) secure the lower support to the middle plate (J).
   

3. Assemble the control box assy (K). Fix it to the middle plate using 4 3/16“ screws.
   

4. Assemble the upper support (D). Insert it to the middle plate (J). Secure with 16 3/16“ screws.
   

5. Assemble the top plate assy (B) to the upper support (D). Secure it using 8 3/16“ screws.
   

6. Assemble the reflector (A) to the top plate assay (B). Screw the 3 studs (BB) on top of the plate assy, then put the reflector on top and secure with 3 wing nuts (AA).
   

7. Carefully install the glass tube (C) by lifting it up and inserting it through the center hole in the top plate (B). Ensure the black silicone ring (F) is attached to the lower edge of the glass tube as illustrated. Slide the glass tube through the hole of the lower plate cover and onto the middle plate (J). Check and ensure that the glass tube is positioned properly and is completely covering the center hole of the middle part.
   • For easier installation place the black silicone ring on its place after you put in the glass tube.
   

8. Assembly the protective guard (E). Hang the hooks of the protective guard onto the holes in supports. Secure the guard with fixing brackets (GG) and 4 3/16“ screws. (DD)
   

9. Attach the three side panels (G) to the heater using 12 1/16“ screws.
   • Note: Do not cover the front side where the control knob is.
   

10. Install the knob to a 14×10 bolt (KK). Hang the chain (LL) to the hole on the control box assy (K) and put the pothook of the front panel (H) to the holes of the bottom plate (N).
    

11. Connect the gas tank to the appliance.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>