HOME DECORATORS COLLECTION Condo Rod Set Instruction Manual
- June 3, 2024
- HOME DECORATORS COLLECTION
Table of Contents
condo Rod set
installation Guide
Condo Rod Set
CAUTION: Before installing brackets, always check there are no hidden
wires or pipes.
WARNING: Product failure due to using incorrect fixings is the
responsibility of the installer. In case of doubt on what anchor to use,
please consult with a professional.
Pre-Installation
NOTICE: Two people may be required for easier installation on larger-
width windows.
PACKAGE CONTENTS
CARE AND CLEANING
To remove dust, use a vacuum cleaner with a brush attachment end or gently rub
the rod using a water-dampened cloth with a mild detergent only.
TOOLS REQUIRED
| Part | Description | Quantity |
|---|---|---|
| A | Wall-end bracket | 2 |
| A-1 | Ring | X1 Per wall-end bracket. |
| A-2 | Base | X1 Per wall-end bracket. |
| B | Bracket | 3 (See NOTICE below) |
| C | Inner rod | 1 |
| D | Outer rod | X1 For length 91.4cm 183cm |
X2 For length 183cm 365.8cm
E| Screw E (Bracket & Base installation)| 8
F| Screw F (Center bracket adjustment)| 3
G| Screw G (Ring adjustment)| 2
H| Screw-in anchors| 8
INSTALLATION
Retain this manual for future use.
Prepare installation
Loosen screws (G) on wall-end bracket rings (A-1) and remove 2-PIECE
telescopic rod (C & D). Disassemble wall-end brackets (A) by unscrewing bases
(A-2) from rings (A-1). Place two bases (A-2) against desired locations from
the walls and ensure they are horizontally aligned, then mark screw holes.
Note: the distance between the center of bracket rings (A-1) and the
ceiling/wall cannot exceed 8cm. Use a tape measure, level, and pencil as
needed.
Mounting to drywall or paneling
Drill horizontally one pilot hole for each wall-end base (A-2) using a 1/4 in.
drill bit, without forcing or enlarging the hole. Screw anchors (H) into the
wall, and install wall-end bracket bases (A-2) by fastening screws (E) into
the anchors (H).
2B Mounting to wood or studs
Drill horizontally one pilot hole for each wall-end bracket base (A-2) using a
3/32 in. drill bit, without forcing the drill or enlarging the hole. Install
wall-end bracket bases (A-2) by fastening screws (E).
Re-assembling wall-end brackets
Fasten rings (A-1) back onto the bases (A-2) to re-assemble wall-end
brackets (A).
NOTICE: In case of two adjacent wall-to-wall windows, install two condo
rod sets. For each rod set, install a wall bracket (A) on one end, a bracket
(B) at center of rod, and another bracket (B) near the corner for maximum
support. Finally, link two condo rods with a corner connector (sold
separately).
Center bracket installation
To identify the bracket (B) position, first, loosen the center bracket
adjustment screw (F). Next, slide the bracket over telescopic rods (C & D) and
temporarily insert rods into both side brackets (A).
Position the bracket base against the ceiling/wall to mark screw
holes.
Remove rods (C & D) and follow steps 24/2B to install brackets with screws (E)
and anchors (H) according to markings. Finally, tighten the center bracket
adjustment screw (F).
5A If rod length is 91.4cm – 183cm
Slide 2-PIECE telescopic rod (C & D) through bracket (B). Feed one drapery
panel through either side and insert the 2-PIECE telescopic rods into the
adjacent wall-end bracket (A). Repeat the operation on the opposite end.
5B If rod length is 183cm – 365.8cm
Take 2-PIECE telescopic rod (C & D) and slide inner rod (C) through bracket
(B). Feed one drapery panel over the telescopic rod (C & D) and insert the
outer rod (D) into the adjacent wall-end bracket (A). Slide extra outer rod
(D) onto inner rod (C) to form a 3-PIECE telescopic rod. Feed a second drapery
panel over the extra outer rod (D) and insert rod (D) onto the other wall-end
bracket (A).
Final adjustments
Fasten screws (G) on wall-end bracket rings (A-1) to secure the telescopic rod
in place. Then tuck and slide drapery panels to desired positions. 
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>