GENESIS IRID 515A RGB LIGHTS Installation Guide

: June 5, 2024
: Genesis

GENESIS IRID 515A RGB LIGHTS

IRID 515A RGB LIGHTS

FAN INSTALLATION

2,5” SSD INSTALLATION

3,5” HDD INSTALLATION

FRONT PANEL I/O PORTS INSTALLATION

Fan Controller Installation

FAN CONTROLLER INSTALLATION

PACKAGE CONTENT

1x
PC case

|

4x
120 mm ARGB fan

|

**3x**
SF1 – Screw stand-off for motherboard

---|---|---

8x
PS1 – Screw for PSU

|

**17x**
MB1 – Screw for Motherboard

8x
HD1 – Screw for HDD in bracket

|

5x
Cable tie

|

1x
Speaker

1x
Motherboard tray spacer screwing tool

|

1x
Installation guide

|

**1x**
Fan controller

FAN INSTALLATION

1. Remove front panel by gently pulling bottom part. Unscrew side panel.
2. Install fans accordingly using screws and according to case plan.
3. Suggested fan airflow orientation.

SSD INSTALLATION

4-7. Put SSD in designated area, then fix it byscrews. Side-cover is necessary to be removed

HDD INSTALLATION

8-9. Remove HDD cage (pull out).
10. As first screw-in HDD drive on top of HDD cage using HD1 (x4) screws into HDD bottom screw holes.
11. Second screw-in HDD drive inside HDD cage using HD1 (x4) screws into HDD side screw holes.

FRONT PANEL O/I PORTS INSTALLATION

12-14. Connect front panel I/O connectors to motherboard according to motherboard manual.

FAN CONTROLLER INSTALLATION

15-16. Plug-in SATA power connector from PSU to controller SATA socket. Backlight mode control via button on front I/O case panel.

USER MANUAL – ARGB FAN CONTROLLER

NOTE: controller is pre-installed and ready to use right after connecting to power source.

CONTROLLER DESCRIPTION

LED1 … LED6 – ARGB backlight headers for fans. To get the right backlight effect, connect the fans one by one. ARGB 3-PIN 5V type header.
SW – To the header can be plugged cable from the front panel of the case – „RESET” or „LED SW” (depends on the model) – terminated with a 2-pin connector. By default cable is pre-installed. RESET/LED button on case allows then to change backlight mode, turn mode off or switch to motherboard control of fans backlight.
DATA (or PC PWM DATA depends on the model) – header with pre installed cable which ends with following connectors:
* PWM –* Connector can be plugged into designated 4-PIN PWM header on motherboard (it must be confirmed in motherboard user manual, if 4-PIN header provides PWM signal or DC). It allows fan speed control from BIOS. If controller is not connected to motherboard, fans run at default RPM. This PWM connector have 2 pins in fact, which is intended and correct.
ARGB –** 3-PIN 5V connector. After plugging into ARGB header on motherboard (check in motherboard user manual for header location and specification), allows fan backlight control from BIOS / motherboard software.

OPTIONAL:

VDG – Gigabyte ARGB 3-pin backlight connector, only compatible with specific manufacturer’s motherboard models.
- FAN1 … FAN6 – 3-PIN fans power connectors.
- LED7, LED8 – LED strip 3-PIN ARGB connectors.
- POWER – SATA power connector

REGULATORY

| EU Declaration of Conformity – Hereby, IMPAKT S.A. declares that that the equipment type NPC-1684 is in compliance with Directives 2014/30/EU and 2011/65/UE. The full text of the EU declaration of conformity is available via the product tab at www.impakt.com.pl
---|---
| The WEEE symbol (the crossed-out wheeled bin) using indicates that this product in not home waste. Appropriate waste management aids in avoiding consequences which are harmful for people and environment and result from dangerous materials used in the device, as well as improper storage and processing. Segregated household waste collection aids recycle materials and components of which the device was made. In order to get detailed information about recycling this product please contact your retailer or a local authority.

SAFETY INFORMATION

Use as intended. Improper usage may damage the device.
Non-authorized repairs or disassembly voids the warranty and may damage the product.
Dropping or hitting the device may lead to device being damaged, scratched or flawed in other way.
Do not use the product in low and high temperatures, strong magnetic fields and damp or dusty surroundings.