zip IP-PTZ622W optical 2mp camera Instruction Manual

zip IP-PTZ622W optical 2mp camera

Introduction

Key Features

The IP-PTZ622 has a 22x optical zoom with auto-focus and a 2MP (1080p) sensor. The PTZ supports 360° endless rotation, up to 300 deg/sec pan speed, up to 100 deg/sec tilt speed. With on board features compatible with the Zip NVR and DVR.

Essential Tools and ZipFinder

•  Laptop / Windows PC
•  Screwdriver
•  Drill
•  Hammer
•  ZIP NVR or DVR
•  PoE Switch / 12V DC power supply
•  Ethernet CAT5/5e/6 Cable

ZipFinder – IP Camera Configuration Tool

• ZipFinder is a Windows PC software for discovering and configuring IP cameras a network.
• Use ZipFinder on non-PoE installs, to help problem solving issues such as forgotten or unknown IP Addresses. To download visit ZipNVR.com

Connections

Powering the camera

• Option 1 – Power the camera from 12V DC / 24V AC (via the 2.1mm Power Socket).
• Option 2 – Power the camera using the PoE(48V) RJ45 Socket.
• When connecting to a ZIP PoE NVR plug the camera directly into the NVRs built in PoE switch.
• When connecting to a ZIP Non-PoE NVR or DVR plug the camera into a separate PoE switch See Setup Option

Connection Wires

Dimensions

Mounting

•  Mark the hole positions using the mounting bracket or using the measurements on the diagram to the right. Drill the holes and install the wall plugs.
•  Feed the PTZ cable loom through the bracket, then secure using the short screws provided. Attach the safety cable from the bracket to the dome..
•  Fit the PTZ to the wall using the screws provided. Ensure the PTZ cable enters via a lower position so that water does not run down to the camera. Use silicon sealant around the base and where the cable enters the PTZ. The connections for the camera need to be installed in a waterproof box or similar.

Setup Options

PoE ZIP NVR

When connecting to a ZIP PoE NVR plug the camera directly into the NVR’s built in PoE switch. The camera should automatically become visible after being connected for approximately 1 minute.

EPoE (Extended PoE)
The 100m distance for a camera can be increased when the PoE Mode is set to EPoE. In the menu on a ZIP PoE NVR go to:-
Video > IP Channels > PoE Mode

Non-PoE ZIP NVR
When connecting cameras to a Non-PoE NVR, they are first connected to an external network switch which is in-turn connected to the NVR as shown below. See Extra Resources for more information on Adding IP Cameras manually to a ZIP Recorder.

PTZ Controls via ZIP NVR or DVR

The PTZ Control screen allows for adjust adjust the zoom, focus, PTZ movement and call presets or create new ones.

•  Click on the image in Live view
•  Click on the PTZ button

PTZ Controls Explained

The buttons on the left hand panel are used to control the camera’s movement, zoom and focus

PTZ Preset Controls
The Preset screen is where you can create presets, call presets and manage cruises.

Camera Selection
You can select which camera you want to control from the Camera drop down list.

Preset Controls Explained

The buttons in the left hand panel are used to position the camera when saving preset locations, creating presets, calling presets, removing presets and starting/stopping cruises. The options available and functions may vary depending on the capabilities of the PTZ itself.

Total Presets
The Total number shows the total number of presets currently in Preset List.

Preset List
The Preset List displays all of the previously set and saved presets in numeric order

• No.: This column shows the Preset Number assigned to the previously saved camera position.
• Time: The Time column shows how long the camera will stay in the preset position before moving on to the next position during a cruise.
• Clear: The Clear button allows you to delete the a preset from the Preset List.
• Go To: Clicking the arrow icon in the Go To column will move the camera to the previously saved position.

Preset Functions

Browser Menu Settings
The menu be configured directly in the browser interface of the camera (standalone), in Remote Setting you will find the menu settings.

Refresh / Save
Camera Settings| IR-CUT Mode| Auto / Colour Mode / Black White Mode / Schedule (B/W)
IR-CUT Delay| 1 ~ 36 (Default 2 )
IR-LED| Auto / Off / On
Flip| Untick / Tick
Mirror| Untick / Tick
Corridor Mode| Untick / Tick
Angle Rotation| 180 / 0
Backlight| Untick / Tick
3D Noise Reduction| Auto / Disable / Manual
DWDR| Untick / Tick
AGC| 1 ~ 128 (Default 64 )
White Balance| Auto / Manual / Indoor
Shutter| Auto / Manual
Time Exposure (max)| 1/5 / 1/8 / 1/15 / 1/25 / 1/50 / 1/100 / 1/150 /

1/180 / 1/200 / 1/240 / 1/250 / 1/300 /

1/360 / 1/480 / 1/500 / 1/600 / 1/700 /

1/1000 / 1/1500 / 1/2500 / 1/5000 /

1/10000 / 1/12000 / 1/20000 / Flickerless

Defog Mode| Disable / Auto / Manual
Refresh / Save / Default
Privacy Mask| Privacy Mark| Untick / Tick
Refresh / Save
ROI| Stream Type| MainStream / SubStream / MobileStream
Region ID| 1 ~ 8
Enable Region| Disable / Enable
ROI Level| Worst / worse / bad / normal / better / best
Non-ROI Fps (1-19)| 12
Refresh / Save
Record| Record Settings| Stream Mode| MainStream / SubStream
Record| Tick / Untick
PreRecord| Tick / Untick
 | Normal Schedule| Customise Schedule
---|---|---
Refresh / Save / Default
Event Schedule| Customise Schedule
Refresh / Save / Default
Network| Network| Type| DCHP / PPPoE / Static
Client Port| 8240
HTTP Port| 80
IP Address| 192.168.10.1
Subnet Mask| 255.255.255.0
Gateway| 192.168.10.254
DNS 1| 192.168.10.254
DNS 2| Untick / Tick
UPNP| Untick / Tick
Multicast| Untick / Tick
P2P Switch| Untick / Tick
Port Range| 1024 ~ 65535 (Client Port, HTTP Port)
Refresh / Save
Encoding| Mainstream| Resolution| 1920×1080 / 1280×960 /

1280×720

FPS| 1 ~ 20 (Default 12 )
Video Code Type| H.264 / H.265
Video Code Level| Main Profile / Baseline / High Profile
Bitrate Control| CBR / VBR
Bitrate Mode| Predefined / User Defined
Bitrate| 256 / 320 / 384 / 448 /

512 / 640 / 768 / 896 /

1024 / 1280 / 1536 / 1792

/ 2048 / 3072 / 4096 /

5120 / 6144 / 8192

Audio| Untick / Tick
I Frame Interval| 1 ~ 80 (Default 24 )
Refresh / Save
SubStream| Resolution| 1280×720 / 640×480 /

320×240

FPS| 1 ~ 20 (Default 10 )
Video Code Type| H.264 / H.265
Video Code Level| Main Profile / Baseline / High Profile
Bitrate Control| CBR / VBR
Bitrate Mode| Predefined / User Defined
Bitrate| 128 / 160 / 192 / 224 /

256 / 320 / 384 / 448 /

 |  |  |  | 512 / 640 / 768 / 896 /

1024 / 1280 / 1536 / 1792

/ 2048 / 3072 / 4096

---|---|---|---|---
Audio| Untick / Tick
I Frame Interval| 1 ~ 80 (Default 20 )
Refresh / Save
MobileStream| Enable| Tick / Untick
Resolution| 640×480 / 320×240
FPS| 1 ~ 20 (Default 10 )
Video Code Type| H.265 / H.264
Video Code Level| Main Profile / Baseline / High Profile
Bitrate Control| CBR / VBR
Bitrate Mode| Predefined / User Defined
Bitrate| 8 / 16 / 24 / 32 / 48 / 64 /

80 / 96 / 128 / 160 / 192 /

224 / 256 / 320 / 384 /

448 / 512 / 640 / 768 /

896 / 1024 / 1280 / 1536

Audio| Untick / Tick
I Frame Interval| 1 ~ 80 (Default 20 )
Refresh / Save
Email Settings| Email| Untick / Tick
Encryption| Disable / SSL / TLS / Auto
SMTP Port| 25 / Customise
SMTP Server| Customise
User Name| Customise
Password| Customise
Sender Email| Customise
Receiver1| Customise
Receiver2| Customise
Receiver3| Customise
Interval| 1Min / 3Min / 5Min / 10Min
Refresh / Save / Test Email / Cancel
DDNS| DDNS| Untick / Tick
Server| NO_IP / DYNDNS
Host Name| Customise
Username| Customise
Password| Customise
IP Filter| Refresh / Save / Add / Del
Filter Mode| Allow all IP connections / Allow the selected IP connections / Block the selected IP connections
RTSP Port| RTSP| Tick / Untick
RTSP Port| 1240 / Customise
 |  | Anonymous Login| Untick / Tick (No username or password required)
---|---|---|---
Instruction: rtsp://IP:Port/ch01/A A:0(MainStream),

1(SubStream), 2(MobileStream)

Refresh / Save
FTP Settings| FTP Enable| Untick / Tick
Server| Customise
Port| 21 / Customise
Username| Customise
Password| Customise
DIR Name| Customise
Transfer Images| Untick / Tick
Refresh / Save
Alarm| Motion Detection| Enable| Untick / Tick
Sensitivity| 1 ~ 8 (Default 3 )
Alarm Out| Untick / Tick
Latch Time| 5S / 10S / 20S / 30S
Post Recording| 5S / 10S / 20S / 30S
Send Email| Untick / Tick
Enable Record| Tick / Untick
Refresh / Save
Alarm Settings| Alarm Input| OFF / NC / NO
Latch Time| 5S / 10S / 20S / 30S
Send Email| Untick / Tick
Alarm Out| Untick / Tick
Enable Record| Untick / Tick
Post Recording| 0S / 5S / 10S / 20S / 30S
Refresh / Save
Lens Covered| Enable| Tick / Untick
Sensitivity| 1 ~ 6 (Default 3 )
Send Email| Untick / Tick
Alarm Out| Untick / Tick
Latch Time| 5S / 10S / 20S / 30S
Refresh / Save
Device| SD Card| SD Card Overwrite| Auto / Close
Refresh / Save
Audio Settings| Enable Audio| Tick / Untick
Output Volume| 0 ~ 10 (Default 5 )
Input Volume| 0 ~ 10 (Default 5 )
Audio Code Type| G711A / G711U / G726 16K
 |  | Refresh / Save
---|---|---
Log| Major Type| Selectable| Search
Start Time| Selectable
End Time| Selectable
PTZ| Protocol| Pelco-D / Pelco-P
Baudrate| 9600 / 4800 / 2400 / 1200
Data Bit| 8 / 7 / 6 / 5
Stop Bit| 1 / 2
Parity| None / Odd / Even / Mark / Space
Address| 1 ~ 254 (Default 254 )
PTZ

Schedule

| Enable| Untick / Tick
Type| Line Scan / Tour / Pattern Scan / Restore
Customise Schedule
Refresh / Save / Default
System| Date/ Time| System Time| Customise
Date Format| DD/MM/YYYY / YYYY/MM/DD / MM/DD/YYYY
Time Format| 24Hour / 12Hour
DST / NTP / Synchronize
Daylight Saving Time| Tick / Untick
Daylight Saving Time| Week / Date
Time Offset| 1Hour / 2Hour
Start Time| Customise
End Time| Customise
Refresh / Save
Users| Select User| Username| Customise
Password| Customise
Confirm| Customise
Active| Tick / Untick
Password| Tick / Untick
Refresh / Save
Info| Device Name
Serial No.
Hardware Version
Software Version
IE Client Version
MAC Address
MCU
P2P ID
Refresh
Smart Analysis| Report type| Daily report / Weekly report / Monthly report / Annual report
Alarm type| Cross Counting (CC ) / Perimeter Intrusion Detection (PID) / Line Crossing
 |  |  | Detection (LCD) / Pedestrian Detection (PD&VD) / Face Detection (FD)
---|---|---|---
Statistical type| Number of in / Number of out / Number of in & out
Start time| Customise
List / Histogram / Line chart
Tools| Firmware Update| Upgrade file path
Scan
Upgrade
Load Default| Camera| Tick / Untick
Record| Untick / Tick
Network| Untick / Tick
Alarm| Untick / Tick
Device| Tick / Untick
System| Tick / Untick
Tools| Tick / Untick
Smart| Tick / Untick
Simple / All / Save
Reboot| Auto Reboot| Untick / Tick
Reboot| Customise
Refresh / Save / Reboot
Smart| Detection| PID| Name| Perimeter Intrusion Detection (PID)
Switch| Untick / Tick
Latch Time| 5S / 10S / 20S / 30S
Post Recording| 5S / 10S / 20S / 30S
Sensitive| 1 / 2 / 3 / 4
Scene| Indoor / Outdoor
Alarm Out| Tick / Untick
Send Email| Untick / Tick
Detection Type| Pedestrian &/or Vehicle
Rule Number| 1 / 2 / 3 / 4
Rule Switch| Untick / Tick
Rule Type| A >B / A<B / A<>B
Enable Record| Untick / Tick
Refresh / Save|
LCD| Name| Line Crossing Detection (LCD)
Switch| Untick / Tick
Latch Time| 5S / 10S / 20S / 30S
Post Recording| 5S / 10S / 20S / 30S
Sensitive| 1 / 2 / 3 / 4
Scene| Indoor
Alarm Out| Tick / Untick
Send Email| Untick / Tick
Detection Type| Pedestrian &/or Vehicle
Rule Number| 1 / 2 / 3 / 4
 |  |  | Rule Switch| Untick / Tick
---|---|---|---|---
Rule Type| A >B / A<B / A<>B
Enable Record| Untick / Tick
Refresh / Save|
PD & VD| Name| Pedestrian Detection (PD&VD)
Switch| Untick / Tick
Latch Time| 5S / 10S / 20S / 30S
Post Recording| 5S / 10S / 20S / 30S
Sensitive| 0 ~ 100 (Default 60 )
Alarm Out| Untick / Tick
Send Email| Untick / Tick
Snap Mode| Interval Mode / Realtime Mode / Default
Snap Num| 1 / 2 / 3 / Unlimited
Snap Frequency| 2 / customise
Min Pixel| 64 ~ 1080 (Default 64 )
Detection Type| Pedestrian &/or Vehicle
Detection Mode| Motion Mode / Static Mode
Detection

Range

| Full Screen / Customize
Enable Record| Untick / Tick
Refresh / Save
FD| Name| Face Detection (FD)
Switch| Untick / Tick
Latch Time| 5S / 10S / 20S / 30S
Post Recording| 5S / 10S / 20S / 30S
Sensitive| 0 ~ 100 (Default 60 )
Alarm Out| Untick / Tick
Send Email| Untick / Tick
Face Enhance| Untick / Tick
Snap Mode| Interval Mode / Realtime Mode / Optimal Mode
Apply Mode| Frontal View / Multi Angle / Customize
Snap Num| 1 / 2 / 3 / Unlimited
Snap Frequency| 2 / customize
Min Pixel| 32 ~ 1080 (Default 32 )
Detection Mode| Motion Mode / Static Mode
Rule Kind| Rect / Line
Detection Range| Full Screen / Customize
Enable Record| Untick / Tick
Refresh / Save

Extra Resources

ZipNVR.com Website
The Zip NVR has a range of information on the cameras and NVRs, manuals, software, tools and support:- www.zipdvr.com

Adding IP Cameras

How to guide on Adding IP Cameras:- www.zipdvr.com/howto/TIP459-How-To-Add- IP-Cameras.html

ZIP Firmware

Firmware for the ZIP products are available online: www.zipdvr.com/firmware.html Compare the firmware in the product against that available online. AI Face Recognition is available on these model NVRs:- ZIP108, ZIP116, ZIP208, ZIP308, ZIP216 and ZIP226.

SPECIFICATIONS

Conditions
All specifications are approximate. System Q Ltd reserves the right to change any product specifications or features without notice. Whilst every effort is made to ensure that these instructions are complete and accurate, System Q Ltd cannot be held responsible in any way for any losses, no matter how they arise, from errors or omissions in these instructions, or the performance or non-performance of the equipment that these instructions refer to. This symbol on the products and/or accompanying documents means that used electronic equipment must not be mixed with general household waste. For treatment, recovery and recycling please return this unit to your trade supplier or local designated WEE/CG0783SS collection point as defined by your local council. © Copyright 2020 Zip is a registered trademark of System Q Ltd, Chesterfield. Derbyshire. S40 2WB

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>