GROUND ZERO GZIA 1.700 Mono Class A/B Amplifier Owner’s Manual

GROUND ZERO GZIA 1.700 Mono Class A/B Amplifier

Features

• High-quality class A/B amplifier
• 1 ohm stable
• Variable high pass filter
• Variable low pass filter
• High-level input with auto-on function
• Adjustable input sensitivity
• Turn-on delay
• Thermal protection
• Short protection
• Overload protection
• Bass level remote control included

General mounting instructions

• As a precaution, it is recommended to disconnect the vehicle’s battery before mounting the amplifier. Note: For new vehicles, disconnecting the battery might cause various errors in your vehicle´s electric system that can be cleared only by authorized service partners of your vehicle´s manufacturer! Please ask your service partner first before disconnecting the battery!

• The power supply wire (+12 V) has to be protected within max. 20 cm / 8” by a main fuse holder with a fuse value matching the recommendation for your amplifier
  Note: If there is more than one amplifier connected using this power wire, the main fuse value must be equal to the sum of the recommended fuses of all connected devices. However, make sure the diameter of your power wire will be enough for the required current!

•  If necessary, replace a defective fuse by a fuse with identical quality and value

• Never drill holes to the vehicle´s gas tank, brake lines, to wirings or any other important vehicle parts!

• Never pass wires over sharp edges or vehicle parts due avoid any kind of damage

• Keep the wiring away from the antenna and electronic devices contributing to radio reception

• Lay the power supply wiring always separated from the speaker wiring to avoid disturbance

• The amplifier contains a temperature protection circuit that turns the device off in case of overheating. After a certain cooling time, it will turn on automatically. To avoid heat build-up, enough air supply for cooling must be provided. Never cover the surface of the amplifier´s heatsink entirely

• The amplifier should NEVER be mounted onto a vibrating part or surface such as a subwoofer enclosure. This might lead to malfunction due to loosened electrical parts inside the amplifier.

• Some amplifiers offer a high-level input option, however if a pre-amplified output (RCA) is available (at the head unit), it is strongly recommended to make use of them.

Specifications

Controls & Features

2

|

Power terminal

| +12V         To be connected to the positive terminal of the battery REM To be connected to the remote output of the head unit*

(*not required in high-level mode)

GND         To be connected to the vehicle´s ground

(or directly to the negative terminal of the battery)

3

|

Fuse(s)

| If necessary to replace a defective fuse, its strongly recommended to use a fuse with the identical value

4

| Low pass filter (Band pass filter)| To adjust the required crossover point. Frequencies above the selected crossover point will be filtered (40 Hz to 4000 Hz)

5

|

Mode switch

| To setup the crossover for the required use of the amplifier FLAT entire frequency range will be reproduced

HPF         only mid/high frequencies will be reproduced

LPF (BP)  only low frequencies will be reproduced. The HPF is activated simultaneously resulting in a band pass filter

6

| High pass filter (Subsonic filter)| To adjust the required crossover point. Frequencies below the selected crossover point will be filtered (5 Hz to 500 Hz)
7| Sensitivity control| Controller to adjust the input sensitivity

8

|

Line input (RCA)

| Input sockets to connect RCA wires

Important note: High-level and RCA inputs should never be used simultaneously! This may cause serious damage to the amplifier

9

|

High-level input

| Head units without RCA pre-amplifier output signal, can be connected using the high-level input to connect the speaker output of the head unit directly.

If used, the amplifier turns on automatically (auto-on feature) The remote input of the power supply terminal remains unused

Important note: High-level and RCA inputs should never be used simultaneously! This may cause serious damage to the amplifier

10| Status indication| POWER (green) ok (correct operation) PROTECT (red) error (protection mode)
11| Remote wire socket| To connect the wired remote control
12| Bass Boost control| To adjust the bass boost level ( 0 to +12 dB @ 45 Hz)

Troubleshooting guide

No audible sound

|

Does the POW LED turn to green?

| Check protection fuse(s) of the amplifier (harness) Check remote wire connection (RCA input mode) Check +12 Volt power supply wire connection

Check ground wire connection

Did the PROTECT LED turned to red?| Check for speaker short or amplifier overheating
Device does not turn on| Power supply of the amplifier?| Check power wire or connections
Remote wire powered? (RCA input

mode)

| Check remote wire connection to the head unit
No sound on one channel| Speaker wiring undamaged?| Check for short circuit or open connections
Input signal on each RCA lead?| Reverse left and right RCA inputs to check the audio input signal
Device turns off at medium / high

volume

| Load impedance of each speaker correct?| Check if each speaker load impedance matches the technical specifications of the amplifier
Status LED turned on red| Temperature protection circuit active| Decrease head unit´s volume / wait for cooling
Speaker wires short / speaker

damaged

| Check speaker / wires and insulate if necessary

Terms of warranty

The limited warranty for this product is covered by GROUND ZERO´s regional distribution partners and their terms and conditions. For further information contact your local retailer or distributor.

Safety instruction / Manufacturer´s declaration

Safety Instructions: Do not expose the device to extreme temperatures, fire, high humidity or direct contact with liquids. Do not use the device if it has been damaged or exposed to liquids. Keep the device, packaging and accessories away from children and pets to prevent accidents and suffocation.
Manufacturer‘s declaration: Herewith Ground Zero GmbH declares that this product complies with the directive 2014/30/EU (EMC) and further declares that this product is in conformity with the rules of the EU directives (including all applicable amendments) 2011/65/EU RoHS2 and 2001/95/EC General Product Safety directive. The full text of the Declaration of Conformity (EU) is available at the following internet address: www.ground-zero-audio.com. Electronic products contain valuable raw materials and must not be disposed of with normal household waste. At the end of its service life, please bring the device to your local recycling facility.

GROUND ZERO products are engineered in Germany GROUND ZERO – an international sponsor
Ground Zero GmbH
Erlenweg 25, 85658 Egmating, Germany Tel. +49 (0)8095/873 830 Fax -8310 www .ground-zero-audio.com

References

• Ground Zero Audio – Car Audio Products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>