FLYING TECH X16 ISDT Professional Dual Channel AC Smart Charger User Guide

June 5, 2024
FLYING TECH

X16 ISDT Professional Dual-Channel AC Smart Charger
User Guide

Thanks for purchasing the ISDT X16 Charger.
Please visit: www.site.co for more details on the functions of this charger, as well as purchase various accessories.
Functions of products will be kept on upgrading, the manual in your hand may be different from the actual operation, please refer to the actual functions.

Warnings and Safety Tips

For your safety and a better user experience, please read this manual and follow the instruction before using the new charger.

  • Never use the charger without supervision, please stop using the charger and refer to the manual for reasons if any functional abnormity.
  • Keep the charger away from dust, humidity, rain, and high temperature, as well as avoid direct exposure to sunlight and intense vibration.
  • Place the charger on a heat-resisting, non-flammable and insulating surface. Do not use it on the car’s seats, carpet, or other similar places. Keep inflammable and explosive objects away from operation areas of the charger.
  • Read the instruction manual carefully to be familiar with the features of the charger, and set proper charging parameters before operating. Setting the parameters incorrectly will result in damage to the product, and personal property and cause serious injury as well.

NEVER USE CHARGER UNSUPERVISED

  • Never attempt to charge primary (non-rechargeable) batteries.
  • Batteries pose a severe risk of fire if not properly handled.
  • Read the entire operation manual before using the charger.
  • This unit may emit heat during use.
  • Only operate this device in a cool ventilated area away from flammable objects.
  • Failure to observe safety procedures may cause damages to property or injury.

WARNING!
FIRE HAZARD!

Specifications

Model No.: X16
Input voltage: AC 100~240V
Output voltage: DC 10~72V
Max. input current: 20A
Charging current: 1~20A
Discharging current: 0.5~3.0A
Max. charging power: 1100W ×2
Max. discharging power: 50W ×2
Balance current: 1.5A/Cell
Supported battery types and cell count: LiFe, LiPo, Liev, ULiHv (2~16S)
Abnormal voltage alarm: Support
Incorrect cell count setting alarm: Support
Working temperature: 0°C~40°C
Storage temperature: -20°C~60°C
Dimension: 276×246×82mm
Weight: About 3450g

Port / Buttons

Preset Battery Type of Charger and Task Parameters

| Rated
Voltage| Full Charge
Voltage| Storage
Voltage| Discharge
Voltage| Balance
Charge| Unbalanced
Charge| Supported
Cell Count| Max. Charging
Current
---|---|---|---|---|---|---|---|---
LiFe| 3.20V| 3.65V| 3.30V| 2.90V| | | 2-16S| 20.0A
LiPo| 3.70V| 4.20V| 3.80V| 3.30V| | | 2-16S| 20.0A
LiHv| 3.80V| 4.35V| 3.85V| 3.40V| | | 2-16S| 20.0A
ULiHv| 3.85V| 4.45V| 3.90V| 3.50V| | | 2-16S| 20.0A

How to Confirm Charging Current

Make sure to know the maximum charging current of the battery before charging, never use excessive current to charge to damage your battery, which will result in overheating or even an explosion during the charging process. The charging and discharging capacity of the battery is usually marked with a C value. Multiplying the charging C value and attery capacity equals the maximum charging current supported by the battery. For example, for a 1000 mAh battery with a charging capacity of 5C, the maximum charging current would be 1000*5=5000mA; therefore, the maximum charging current is 5A. For a lithium battery, if it is impossible to confirm the supported charging C value, please set the charging current below 1C, for the sake of its (lithium battery) safety. The reference relation between C value and charging time: charging time ≥60 minutes/ charging C value e.g. it needs around 60-70 minutes to complete charging with 1C). Due to differences in battery conversion eiciency, the time to complete the charging might be extended.

Operating the Charger

Connect the charger to the power supply, short-press the power button to start the machine, connect the battery, and long-press the middle button on the corresponding channel side to enter the task setting menu. In the task setting interface, tasks can be preset. Up to 8 preset tasks can be set. In addition to preset tasks, custom task Settings can also be carried out. The setting menu is as follows:

Task Charge, Discharge, Storage
Battery LiFe, LiPo, LiHv, ULiHv
Current 1.0~20.0A
Battery and cell count LiFe, LiPo, LiHv, ULiHv (2~16S)

Charge

A balancing port is strongly recommended when charging the lipo battery, which can make sure to monitor the voltage on each cell battery and balance it when charging.
Warning beeper will yell before starting charging lipo if in non-balanced mode (no connecting with balance port).

Charging Screen

Press the up and down button to switch the detailed information display content, as cell voltage, cell internal resistance, and working parameter. The cell voltage and internal resistance are only on display in balancing charging mode.

System Setting Menu

On the standby interface, long-press the left and right middle keys at the same time to enter the system setting menu.
The menu items are as follows:
Volume
There are 4 options of High Mid Low and Of for volume setting. When the setting is OFF, it will turn of the operation sound, but not the warning error beep.
Self-test
When all batteries on CH1 and CH2 ports are not connected, please select this option to self-test task manually.
Calibration the input voltage, output voltage, and balance voltage of the charger can be calibrated with this task.

http://www.isdt.co 
Scan the code for more information
All product photos, statements, and literature are for reference only. For up-to-date information,
please visit our official web www.is.co. SHENZHEN ISD TECHNOLOGY CO. LTD reserves the right of initial explanation and revision for the terms.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals