GL Technologies AP1300C4 Wireless Access Point User Manual

June 5, 2024
Gl Technologies

GL Technologies AP1300C4 Wireless Access Point

SETTING Up

Power On
When powered up, your GL-AP1300 will broadcast two Wi-Fi signals with the sSID:
GL-AP1300-xxx and GL-AP1300-xxx-56.
The POE injector should be compatible with active o passive 48V 802.3at standard.

Connect to the Wi-Fi

  • Connect to the 2GHz W-Fi called
  • GL-AP1300-xxx, and input the default Wi-Fi
  • password Goodlife, which is also printed on the bottom of the router.

Set up Router
Visit http://192.168.8.1 in your browser to set up your router; start by choosing your preferred language.

POWER SUPPLY OPTIONS

PoE power over Ethernet)
The PoE injector should be compatible with 48V 802.3at standard. PoE only works on the WAN port.GL Technologies AP1300C4 Wireless Access Point fig
4

Power cable
Please use power cable (12V/2A DC).GL Technologies AP1300C4 Wireless
Access Point fig 5

SUPPORT

GL Technologies AP1300C4 Wireless Access Point fig
6

Repair/Reset
If you cannot access the web-based setup page or cannot connect to the router,
you can press the Reset button:
Press and hold for 3 seconds, and then release to repair your network.
Press and hold for 10 seconds, and then release to reset the router
to factory settings. All user data will be cleared.

Technical Support
For more detailed and updated instructions, please visit our website docs.gl- inet.com
For further questions, you can get help from the following ways:

Email to support@gl-inet.com
Message us on our Facebook: facebook.com/gl.inet. wifi/Post questions in our forum: forum.gl-inet.com
Ask professionals in other forums e.g. OpenWrt, LEDE or other professional websites

WITH 4G MODULE

GL Technologies AP1300C4 Wireless Access Point fig
7

Insert Nano SIM Card & Attach the External Antennas
Insert Nano SIM Card and attach the antennas before connecting to a power supply.

  • Hot-plug for nano-SIM card is not supported for this router.

WARRANTY

  • We provide one-year limited waranty for routers and 3-month limited warranty for accessories. Extra waranty may apply according to the local law in which the product purchase took place.
  • Highly recommend using the included 12V/2A power adapter.
  • Any damage to the router caused by not following the instructions will render this warranty null and void.
  • Any damage to the router caused by modifying the PCBA, components or case will render this warranty null and void.
  • Issues caused by the use of third-party firmware may not get official support from us.
  • Any damage to the router caused by inappropriate use, e.g. inappropriate voltage input, high temperature, dropping in the water or on the ground will render this warranty null and void.
  • Pictures on the instructions are only for reference. We reserve the right to change or modify these materials without further notice.

FCC Rules

This device comples with Part 15 of the FCC Rules. Operation is subject to the following twO Conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation 2. Changes or modifications not expressly approved by the party responsible for compliance coud void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Cass B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will nat occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the follawing measures:

  • Reorient Oe relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help with important announcement

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum
distance 20cm between the radiator and your body This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter The Equipment named above is confirmed to comply with the requirements setout in the European Council Directive on the Approximation of the Laws of the Member States relsting to RED (2014/53/EUJ. The equipment passed the
test which was performed according to the follbwing European standards:

Caution:
The device for operation in the band 51 50-5250 MHz is only for indecr use to reduce the potential for harmful interference to co-channel mobile satellte systems
This product uses WiF 2.4GHz Operating Frequency is 2400-2483.5MHz
5GHz Operating Frequency is 5150-5250MHz and 5725-5850MHz;
EN 301 489-1 2.1.1: EN 301 489-17 V3.1.1: EN 301 489-52 V1.1.0
EN 300 328
EN 301 893 V2.1.1
EN 62311:2018
The Product comply with Directive 2011/65/EU and its

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals