TAKAZONO JC-SE-R-001 Film Core Drum User Manual

TAKAZONO JC-SE-R-001 Film Core Drum

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

• Model: JC-SE-R-001
• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
• Takazono America
  Address: 3555 Voyager St. Suite 102 Torrance, CA 90503 U.S.A.
  Phone : +1-310-542-8850

System Description

• This system equipped with an RFID reader / writer and determines the type of packaging paper based on the contents of the set “RFID tag” (mounted on “film core).
• The type of “RFID tag” corresponds to the international standard ISO15693, and the conformity tags are YTBP01-129 (by YRSC).
• The packaging paper wrapped around the film core is packaged at the sealing temperature according to the type of “RFID tag”.
• For the “Power supply”, DC5V are required.
• It operates by sending a command form the “Host device” via RS232C.

Connection

• ”Power and Communication connector” ・・・（HIROSE： DF-11-4DS-2C）

Operating

• Supply to “Power and Communication connector” DC5V.
• Send the following commands from the “Host device”.

Command-List
The behavior is determined by a state machine capable to perform a certain set of commands. By writing a command-code to the command register the command is executed.
Arguments and/or data necessary to process a command, are exchanged via the FIFO buffer.

• Each command that needs a certain number of arguments will start processing only when it has received the correct number of arguments via the FIFO buffer.
• The FIFO buffer is not cleared automatically at command start. It is recommended to command afterwards.
• Each command may be stopped by the host by writing a new command code into the command register e.g.: the Idle-Command.

Command set

18000-3 mode 3/ EPC Class-1 HF

Receive| 05h| –| activates the receive circuit
Transmit| 06h| bytes to send: byte1, byte2,….| transmit data from the FIFO buffer
Transceive| 07h| bytes to send: byte1, byte2,….| transmits data form the FIFO buffer and automatically

activates the receiver after transmission finished

WriteE2| 08h| address H, address L, data;| gets one byte form FIFO buffer and writes it to the

internal EEPROM

WriteE2Page| 09h| (page Address), data0, [data1 ..data63];| gets up to 64 bytes (one EEPROM page) form the FIFO

buffer and writes it to the EEPROM

ReadE2| 0Ah| address H, address L, length;| Reads data from the EEPROM and copies it into the

FIFO buffer

LoadReg| 0Ch| (EEPROM address H), (EEPROM

address L), RegAdr, (number of Register to be copied);

| reads data from the internal EEPROM and initializes

the SLRC610 registers. EEPROM address needs to be within EEPROM sector 2

LoadProtocol| 0Dh| (Protocol number RX), (Protocol

Number TX);

| reads data from the internal EEPROM and initializes the

SLRC610 registers needed for a Protocol change

ReadPNR| 1Ch| –| copies bytes form the Random Number generator into

the FIFO until the FIFO is full

Soft Reset| 1Fh| –| reset the SLRC610

This film core drum reader/writer uses SLRC61003HN. Refer to the SLRC61003HN data sheet for more details.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>