BAQICK WP9510 Label Maker Machine User Guide
- June 14, 2024
- BAQICK
Table of Contents
BAQICK WP9510 Label Maker Machine
Package
Product View
Power ON/OFF
- Long press 2 seconds to Turn ON/OFF
- The indicator light is on Normal running/fully charged.
- The indicator light flashes quickly: Error running (Lack of paper, the direction of the paper reversed, Low Battery Indicator, Printing head overheating).
- The indicator light flashes slowly: Charging.
Charging
Please plug the device into the USB cable and connect it to a 5V -1A adapter
or the computer for charging fully before the first use. When the indicator
light flashes quickly during charging, check if it means a lack of paper. If
so, then load the thermal paper, next check if the charging is normal. The
product is sold without a power adapter. The user manual stated if consumers
use a power adapter for power supply, they should buy a matching power
adapter that has obtained CCC certification and meets the standard
requirements
Reset
When the device does not respond, try to insert the pin/toothpick into the
reset hole for 3 seconds and then release.
Download “iLabel” APP
Wayl: The user can scan the QR code below. more of the door die or to court 9
Wayz search “towel and pp Store/ Google Play to download it May to come on do
Elick QR code by cellphone to download ¡Label” APP.
Connect to printer
Step1
Open the app, and allow it to access your Bluetooth settings, and enter the
device Search page.
Step2
After connecting the device, go to the label creation pace.
Step3
Once finished creating the label, select “Print.” Then confirm the print density and label quantity, and click “Print” again.
Replace the Thermal Paper
- Refer to picture(1) to push and open the flip cover.
- Pater: the nether piper thing thermal
- Refer to picture(3) to pull out a piece of paper to the outside of the device, and then watch the pining pa to avoid scalding
Parameters
- Product Dimension: 10’86.232.5mm
- Print Type: Thermal Printing
- tabe Width: mm
- Paper Cutting Method: Manual paper cutting
- Capacity: 1000mAh Lithium Battery
- charging Time: ADoU Hours
- Input: 5V m]A
- Charging Port: Type-C
Safety Precautions
- This product has with built-in lithium battery, please do not use it higher than so c. Do not close to the
- Tire and inner sources as soar message.
- Do not remove. impinge. Duncture or modify the battery. Do not use the battery for other purposes
- Do not put the product in fire or water to avoid short circuits or the battery causing fire or burns.
- Please do not use this product in bib humidity or dusty areas
- Please gently insert or unplug the charging cable to prevent excessive force from damaging the Chardin interface.
Frequently Asked Questions
Q: No connectable devices were found when adding devices?
A: When adding the device, please check whether the power of the device is
enough to work.
Q: The device can not print. How to do?
A: Confirm whether the Bluetooth of the mobile phone is on, and exclude the
possibility of others connecting to this device. Check whether the thermal
paper has been used up, and timely replacement of the thermal paper. The
printing head is overheating, if overheating, please let the printing head
cool before trying to print. Restart the device, if still can not be solved,
please use the pin inserted into the reset hole for reset.
Q: Why is it all white papers instead of content?
A: It may be caused by the incorrect installation of the thermal paper. Please
refer to the introduction of replacing the thermal paper for re-installation.
Q: Why can’t stop printing without content?
A: It may be that the type of consumables is not chosen correctly. If the APP
chooses gap paper, this situation will occur when the device is directly
changed to continuous paper without shutting down. Please re-select the
consumable type in the APP.
Q: Why is the print getting lighter?
A: 1 Check whether the device has a low battery. Check whether the printing
head and wheel are covered with carbon ink, please wipe with alcohol softly.
Q: The label paper is not printed correctly?
A: In the power-on state, put the label paper into the device, and click the
button five times consecutively for calibration. After pushing out the 2
labels, the calibration is complete.
Q: What is the size of the thermal paper included with the product?
A: The thermal paper included with the product is a roll with a size of
12×40mm (0.47″ ×1.57″).
Q: Do I need to purchase specific labels?
A: Yes, you need to purchase specific labels. To buy them, please search
for “brand + labels” on Amazon, or Find your order for the label maker and
contact customer service.
Q: Does the label printer need ink?
A: No, it does not require ink as it is a thermal printing machine.
Q: What should I do if I have a problem that I can’t solve?
A: Please contact our staff anytime via email at “brooker-
amazon@foxmail.com”
(US) “abbydream@outlook.com”
(UK) “amayashoultzs77106@gmail.com”
(DE) or you can contact us through Amazon.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>