DURABOOK Z141 Laptop Discrete VGA Expansion Chassis User Manual
- June 5, 2024
- Durabook
Table of Contents
DURABOOK Z141 Laptop Discrete VGA Expansion Chassis
Package Contents
If any of the following items are damaged, please contact your retailer.
- Adapter
- Power code
- Expansion chassis with Rubber gasket
- Bottom cover with PCIe cables
- Expansion brackets (2)
Screw Name | Screw Type | Quantity |
---|
ISOT-M3.0X10L
| |
6 (bumpers)
ISOT-M3.0X7L|
| 8 (bumpers)
ISOT-M2.6X3L|
| 4 (expansion chassis)
ISOT-M2.6X8L & O RING| |
6 (expansion chassis)
ISOT-M2.6X4L| | 4 (expansion brackets)
14 (bottom cover)
NOTE: The pictures are for reference only, actual items may slightly differ.
Installation
- This section will guide you on how to install the discrete VGA expansion chassis to your notebook.
NOTE: For Z14I laptop equipped with discrete NVIDIA graphic MXM expansion box, a 120W power adapter must be use.
Installing the Discrete VGA Expansion Chassis
To install the expansion chassis, follow the steps below:
- Remove the 14 screws securing the bumpers.
- ISOT-M3.0X10L (A): 6 screws
- ISOT-M3.0X7L (B): 8 screws
- Remove the bumpers.
- Pry to remove the mylar from the lower case.
- By aligning with the screw holes, install the expansion brackets onto their respective slots.
NOTE: Ensure that the 4 O-rings ( ) are properly embedded in the upper part of the screw holes (C).
- Attach the 4 screws (ISOT-M2.6X4L) to secure the expansion brackets to the lower case.
- Place the expansion chassis on the top of the lower case. Ensure that the screw holes are properly aligned.
NOTE: If you have difficulty aligning the screw holes, lift the chassis and loosen the 4 screws securing the expansion brackets (see Step 5). Then place the chassis onto the lower case and re-align the screw holes (D) with the screw holes on the brackets. After verifying the screws holes are properly aligned, lift the chassis again, and then fasten the 4 screws to secure the expansion brackets.
- Attach the 4 screws (ISOT-M2.6X3L) first to secure the expansion chassis to the lower case. Then continue to attach the remaining 6 screws (ISOT-M2.6X8L).
- ISOT-M2.6X3L (F): 4 screws
- ISOT-M2.6X8L (E): 6 screws
NOTE: Ensure that the O-ring is embedded with the ISOT-M2.6X8L screw.
- With the protruding tabs facing down, install the rubber gasket onto its compartment. Press down each tabs to ensure that the gasket is properly seated in place.
CAUTION: To ensure the correct placement and orientation, please observe the printed direction (G) when installing the rubber gasket.
- Connect the PCIe coaxial cable to the mainboard connector. Then connect the PCIe power cable to the mainboard connector and secure the latch.
- Place the bottom cover onto the chassis.
- Attach the 14 screws (ISOT-M2.6X4L) to secure the bottom cover.
Discrete VGA Expansion Chassis Screws
Screw Name | Screw Type | Quantity | Torque |
---|
ISOT-M3.0X10L
| |
6 (bumpers)
| ****
2.5 ± 0.3 Kgf-cm
ISOT-M3.0X7L|
| 8 (bumpers)| 2.5 ± 0.3 Kgf-cm
ISOT-M2.6X3L| ****
| 4 (expansion chassis)| 2.5 ± 0.3 Kgf-cm
ISOT-M2.6X8L & O RING| ****
| 6 (expansion chassis)| ****
2.5 ± 0.3 Kgf-cm
ISOT-M2.6X4L
| ****
| 4 (expansion brackets)| 2.5 ± 0.3 Kgf-cm
14 (bottom cover)| 3.5 ± 0.3 Kgf-cm
Twinhead International Corp.
- 11F, No.550, Ruiguang Rd., Neihu, Taipei 11492, Taiwan, R.O.C.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>