DURABOOK R11 Rugged Tablet Expansion Modules with GLAN RS232 Smart Card User Manual
- June 4, 2024
- Durabook
Table of Contents
R11 Rugged Tablet Expansion Modules
GLAN_RS232_Smart Card (3-in-1)
User Manual P/N:
62+030990+40
© 2021 Twinhead International Corp and/or its affiliates. All rights reserved.
Package Contents
If any of the following items are damaged, please contact your retailer.
Expansion Modules GLAN_RS232_Smart Card (3-in-1)
GLAN, RS232, and Smart Card (3-in-1) Module Screws
Screw Name | Screw Type | Quantity | Torque |
---|---|---|---|
ISOT-M2.0X4L | 2 (bracket to lower case) | 2.0 ± 0.3 Kgf-cm |
4 (3-in-1 board to bracket)
ISOT-M2.0X7L| | 3 (smart card reader to bracket)| 2.0 ± 0.3 Kgf-cm
ISOT-M2.6X4L| | 2 (cover to lower case)| 2.0 ± 0.3 Kgf-cm
M2.6X6L 8c 0 RING| | 4 (cover to lower case)| 2.0 ± 0.3 Kgf-cm
Standoff| | 2| 3.0 ± 0.3 Kgf-cm
NOTE
The pictures are for reference only, actual items may slightly differ.
Installation
This section will guide you on how to install the expansion modules to your
tablet PC.
Note: Make sure to remove the battery before installing any type of expansion
module. For more information on how to remove/install the battery, please
refer to the tablet PC service guide.
Installing the GLAN, RS232, and Smart Card (3-in-1) Module
To install the GLAN, RS232, and smart card module, follow the steps below:
-
Remove the screw securing the mylar on the DDR door.
-
Remove the mylars from the DDR door.
-
Attach the expansion sponge and four sponges to the DDR door.
-
Connect the 3-in-1 module FPC to the mainboard connector.
-
By aligning with the screw holes, install the RJ-45 bracket onto its slot on the lower case.
-
Attach the 2 screws to secure the RJ-45 bracket to the lower case.
-
Connect the 3-in-1 module FPC to the 3-in-1 board connector.
-
Attach the tape to secure the 3-in-1 module FPC in place.
-
Connect the smart card module FPC to the 3-in-1 board connector.
-
Attach the tape to secure the smart card module FPC in place.
-
By aligning with the guide pins and I/O port compartment, install the 3-in-1 board onto the RJ-45 bracket.
-
Attach the 4 screws to secure the 3-in-1 board to the bracket.
-
Fold the excess of the 3-in-1 module FPC and place it onto the 3-in-1 board. Then, by aligning with the screw holes, place the smart card reader on the top of the installed 3-in-1 board.
-
Attach the 3 screws to secure the smart card reader in place.
-
By aligning with the screw holes, place the gasket onto the RJ-45 bracket.
-
By aligning with the screw holes, install the 3-in-1 module cover on the top of the installed gasket.
-
Attach the 6 screws to secure the 3-in-1 module cover to the lower case.
➢ M2.6X6L & O RING (marked with a blue-white circle): 4 screws
➢ ISOT-M2.6X4L (marked with an orange-white circle): 2 screws -
Install the 2 standoffs to the RS232 port module.
-
Close the I/O port covers.
-
Install the battery.
Twinhead International Corp.
11F, No.550, Ruiguang Rd., Neihu, Taipei 11492, Taiwan, R.O.C.
Documents / Resources
|
DURABOOK R11 Rugged Tablet Expansion Modules with GLAN RS232 Smart
Card
[pdf] User Manual
R11, Rugged Tablet Expansion Modules with GLAN RS232 Smart Card, R11 Rugged
Tablet Expansion Modules with GLAN RS232 Smart Card
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>