DURABOOK R11 Rugged Tablet Expansion Modules HF RFID User Manual

June 4, 2024
Durabook

R11 Rugged Tablet
Expansion Modules
HF RFID
User ManualDURABOOK R11 Rugged Tablet Expansion Modules HF RFID
-

Package Contents

If any of the following items are damaged, please contact your retailer.

DURABOOK R11 Rugged Tablet Expansion Modules HF RFID - Package
Contents

HF RFID Module Screws

Screw Name Screw Type Quantity Torque
ISOT-M2.0X4L 2 (bracket to lower case) 2.0 ±0.3 Kgf-cm
ISOT-M2.6X4L 2 (expansion board to bracket) 2.0 ±0.3 Kgf-cm
M2.6X6L& O RING 4 (cover to lower case) 2.5 ±0.3 Kgf-cm

NOTE
The pictures are for reference only, actual items may slightly differ.

Installation

This section will guide you on how to install the expansion modules to your tablet PC.
Note: Make sure to remove the battery before installing any type of expansion module. For more information on how to remove/install the battery, please refer to the tablet PC service guide.

Installing the HF RFID Module
To install the HF RFID module, follow the steps below:

1. Remove the screw securing the mylar on the DDR door.| 2. Remove the mylars from the DDR door.
---|---
DURABOOK R11 Rugged Tablet Expansion Modules HF RFID - Fig
1| DURABOOK R11 Rugged Tablet Expansion
Modules HF RFID - Fig 2
3. Attach the expansion sponge to the DDR door. Then install the sponges onto
the screw holes.| 4. Connect the expansion FFC to the mainboard connector. Then secure the
latch.
DURABOOK R11 Rugged Tablet Expansion Modules HF RFID - Fig
3| DURABOOK R11 Rugged Tablet Expansion
Modules HF RFID - Fig 4
5. Route the expansion FFC through the opening on the RFID module bracket.
Then, by aligning with the screw holes, install the bracket onto its slot on the lower case.| 6. Attach the 2 screws to secure the RFID module bracket to the lower case.
DURABOOK R11 Rugged Tablet Expansion Modules HF RFID - Fig
5| DURABOOK R11 Rugged Tablet Expansion
Modules HF RFID - Fig 6
7. Connect the expansion FFC to the RFID expansion board connector. Then secure the latch.| 8. Attach the tape to secure the expansion FFC in place.
DURABOOK R11 Rugged Tablet Expansion Modules HF RFID - Fig
8| DURABOOK R11 Rugged Tablet Expansion
Modules HF RFID - Fig 9
9. Flip the RFID expansion board. Then, by aligning with the screw holes, install the RFID expansion board onto its slot on the RFID module bracket.| 10. Attach the 2 screws to secure the RFID expansion board to the bracket.
DURABOOK R11 Rugged Tablet Expansion Modules HF RFID - Fig
10| DURABOOK R11 Rugged Tablet
Expansion Modules HF RFID - Fig 11
11. By aligning with the screw holes, place the gasket onto the installed bracket.| 12. Attach the rubbers to their respective slots on the RFID module bracket.
Make sure that those rubbers are properly attached to the designated slots
(alignment marked by dotted red lines) as shown in the below illustration.
DURABOOK R11 Rugged Tablet Expansion Modules HF RFID - Fig
12| DURABOOK R11 Rugged Tablet
Expansion Modules HF RFID - Fig 13
13. Connect the RFID module FPC to the RFID expansion board connector. Then secure the latch.| 14. Attach the tape to secure the RFID module FPC in place.
DURABOOK R11 Rugged Tablet Expansion Modules HF RFID - Fig
14| DURABOOK R11 Rugged Tablet
Expansion Modules HF RFID - Fig 15
15. By aligning with the screw holes, place the RFID module cover (with the preinstalled HF RFID board) onto the installed gasket.| 16. Attach the 4 screws to secure the RFID module cover to the lower case.
17. Install the battery.
DURABOOK R11 Rugged Tablet Expansion Modules HF RFID - Fig
16| DURABOOK R11 Rugged Tablet
Expansion Modules HF RFID - Fig 18

Twinhead International Corp.
11F, No.550, Ruiguang Rd., Neihu, Taipei 11492, Taiwan, R.O.C.
P/N: 62+030990+50
© 2022 Twinhead International Corp and/or its affiliates. All rights reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals