Angekis U2-12FHD30 Saber U2 PTZ Camera User Manual

Angekis U2-12FHD30 Saber U2 PTZ Camera

SAFETY GUIDES

1. Before operation, please fully read and follow all instructions in the manual. For your safety, always keep this manual with the camera.
2. The camera power input range is 100-240VAC(50-60Hz),ensure the power supply input within this rate before powermg on.
3. The camera power voltage is 12VDC, rated currency is 1.5A. We suggest you use it with the original power supply adapter supplied by the factory.
4. Please keep the power cable, video cable and control cable in a safe place. Protect all cables especially the connectors.
5. Operational environment: 0°C-50°C, humidity less than 90%.To avoid any danger, do not put anything inside the camera, and keep away from the corrosive liquid.
6. Avoid stress, vibration and damp during transportation, storage and installation.
7. Do not detach the camera housing and cover. For any service, please contact authorized technicians.
8. RF cable and control cable should be individually shielded, and cannot be substituted with other cables. Do not direct the camera lens towards strong light, such as the sun or the intensive light.
9. Use a dry and soft cloth to clean the camera housing. Applied with neutral cleaning agent when there is need to clean. To avoid damage on the camera lens, never use strong or abrasive cleaning agents on the camera housing.
10. 10.Do not move the camera by holding the camera head. To avoid mechanical trouble, do not rotate the camera head by hand.
11. Put the camera on fixed and smooth desk or platform, avoid leaned installation.
12. Power Supply Polarity(Drawing)

ACCESSORIES

Check all bellow items when open the package:

• Camera········································································ 1
• Power Adapter································································ 1
• Power Cable·································································· 1
• RS232 Control Cable························································ 1
• USB2.0 Cable ………………………………………………………. 1
• Remote Controller··························································· 1
• User Manual·································································· 1
• Double-sided Adhesive …………………………………………….. 1

QUICK START

1. Check all cable connections before power on.
2. DIP Switch Setting (at the bottom of the camera):

 |  | Function| (ARM)|
---|---|---|---|---
SW-1| SW-2|  | Instruction
1| OFF| OFF|  | Updating mode
2| ON| OFF|  | Debugging mode
3| OFF| ON|  | Undefined
4| ON| ON|  | Working mode
SW-3| SW-4| Instruction
---|---|---
1| OFF| OFF| Off(Close IR receiver)
2| ON| OFF| Undefined
3| OFF| ON| SEJIN 4PPM CODE
4| ON| ON| NEC CODE(standard)
 |  |

Function

|

(USB)

 | SW-5| SW-6| Instruction
1| OFF| OFF| Undefined
2| ON| OFF| Working mode
3| OFF| ON| Updating mode
4| ON| ON| Undefined

PRODUCT HIGHLIGHTS

• Smart and fashion design, ideal for cloud-based conferencing
• Adopts advanced DSP , 1/2.8 in MP image sensor, and high quality 12X 72.5degree FOV optical lens, provides fluent and crystal image quality
• Fast switching between different video formats: less than 1 second
• 12X Optical Zoom+ 12XDigital Zoom
• Fast and accurate focus performance
• Easy firmware upgrade-(field -upgradable)
• USB2.0 high speed output
• Effective RS232/485 serial control
• Up to 128 presets
• Compatible with the majority of videoconferencing software (UVCl.5 protocol standard)
• With powerful functional remote controller
• IR transfer/IR pass function: except receiving the camera remote controller signal, the camera can also receive other code’s IR remote control signal, and pass these IR control signal to the codec’s IR receiver (via VISCA IN port).

PRODUCT SPEC

CAMERA INTERFACE Camera Lens 

1. Camera Base
2. IR Receiver Panel
3. indicator Light
4. Dial Switch
5. Tripod Screw Hole
6. installation Hole
7. RS232(VISCA IN) Port
8. USB2.0 Port
9. DC12V Power Input
10. Power Indicator light (red)

CAMERA DIMENSION(MM)

IR REMOTE **CONTROLLER

**

Video mute
Short press Video mute button to turn off the camera and short press again to turn it on.
Power Key
Under normal working mode,short press Power key to let the camera enter standby mode;Press it again,the camera will do self-configuration and then go back to HOME position; It will go to preset position if the power on mode has been set.

Address/Camera Setting Key
Set+(Cam 1 ~Cam4 ):set camera’s remote control address. Short press Cam1 ~Cam4 to select the camera

Number Key
Set Presets: Set+(0~9)to set preset.
Recall Presets: Short press the(0~9)number key to recall presets.

Clear Key
Clear+(0~9): to clear the relative preset; Long press to clear all preset.

Menu Key
Ok: to confirm the menu selection Menu: enter/exit menu
Back: back to previous menu

F+/F-: Set focus by manual, only valid under manual focus mode.
T/W: Set the lens zoom rate.
Navigate Key: Up/Down/Left/Right Under normal working mode, use navigate key to set the pan tilt, and select values when enter OSD.
Home Key: Under normal working mode, short press Home key to let the camera go back to home position.

Flip: Enable/Disable the picture up/down flip;
Mir: Enable/Disable the picture left/right flip;
MF: Enable manual focus model;
AF: Enable manual focus model. SHARP: Set sharpness level;
NR+/-: Set noise reduction level;
Reset: Long press(3S) to reset camera;
Rev: Display camera revision;

Note: under specific environment, due to heavy infrared interfere, (such as if put the camera on a big infrared touch screen, or if there is a strong iodine-tungsten lamp in the room), it may affect the infrared remote receiver performance, which may cause wrong control/movement. In this case, if the user doesn’ t need to use the remote controller, we suggest to dial the SW3-4 to OFF, to close the infrared signal receiving.

VICSA IN (RS232) PORT

VISCA IN &RS485 Connection 

VISCA IN &D89 Connection

SERIAL PORT CONFIGURATION:

VISCA PROTOCOL
Partl Camera Return Command

Ack/Completion Message

 | Command Packet| Note
ACK| z0 41 FF| Returned when the command is accepted.
Completion| z0 51 FF| Returned when the command has been executed.
Error Messages

 | Command Packet| Note
Syntax Error| z0 60 02 FF| Returned when the command format is different or when a command with illegal command parameters is accepted
Command Not

Executable

|

z0 61 41 FF

| Returned when a command cannot be executed due to current condi ti ons. For example, when commands controlling the focus manually are received during

auto focus.

Part2     Camera Control Command

CAM Power

| On| 8x 01 04 00 02 FF| ****

Power ON/OFF

Off| 8x 01 04 00 03 FF

CAM Zoom

| Stop| 8x 01 04 07 00 FF|
Tele(Standard)| 8x 01 04 07 02 FF
Wide(Standard)| 8x 01 04 07 03 FF
Tele(Variable)| 8x 01 04 07 2p FF| ****

p = 0(low)~7(high)

Wide(Variable)| 8x 01 04 07 3p FF
Direct| 8x 01 04 47 Op 0q Or Os FF| pqrs: Zoom Position       (0(wide)

~ox4000(tele))

CAM Focus

| Stop| 8x 01 04 08 00 FF|
Far(Standard)| 8x 01 04 08 02 FF
Near(Standard)| 8x 01 04 08 03 FF
Command| Funnation| Command Packet| Note
---|---|---|---
 | Direct| 8x 01 04 48 Op 0q Or Os FF| pqrs: Focus Position
One Push AF| 8x 01 04 18 01 FF|

CAM ZoomFocus

| ****

Direct

| 8x 010447 Op 0q Or Os 0t Ou 0v Ow FF| pqrs: Zoom Position       (0(wide)~ 0x4000(tele))

tuvw: Focus Position

CAM WB

| Auto| 8x 01 04 35 00 FF|
Indoor| 8x 01 04 35 01 FF|
Outdoor| 8x 01 04 35 02 FF|
OnePush| 8x 01 04 35 03 FF|
Manual| 8x 01 04 35 05 FF|
Outdoor Auto| 8x 01 04 35 06 FF|
Sodium Lamp

Auto

| 8x 01 04 35 07 FF|
Sodium Auto| 8x 01 04 35 08 FF|

CAM RGain

| Reset| 8x 01 04 03 00 FF| ****

Manual Control of R Gain

Up| 8x 01 04 03 02 FF
Down| 8x 01 04 03 03 FF
Direct| 8x 01 04 43 00 00 Op 0q FF| pq: R Gain       (Q~QxFF)

CAM_Bgain

| Reset| 8x 01 04 04 00 FF| ****

Manual Control of B Gain

Up| 8x 01 04 04 02 FF
Down| 8x 01 04 04 03 FF
Direct| 8x 01 04 44 00 00 Op 0q FF| pq: B Gain       (0-0xFF)

CAM AE

| Full Auto| 8x 01 04 39 00 FF| Automatic Exposure mode
Manual| 8x 01 04 39 03 FF| Manual Control mode
Bright| 8x 01 04 39 OD FF| Bright mode(Manual control)

CAM Shutter

| Reset| 8x 01 04 0A 00 FF| ****

Shutter Setting

Up| 8x 01 04 0A 02 FF
Down| 8x 01 04 QA 03 FF
Direct| 8x 01 04 4A 00 00 Op 0q FF| pq: Shutter Position       (o~ox15)

CAM Iris

| Reset| 8x 01 04 OB 00 FF| ****

Iris Setting

Up| 8x 01 04 OB 02 FF
Down| 8x 01 04 OB 03 FF
Direct| 8x01044B00000p0qFF| pq: Iris Position         (o~ Oxll)

CAM Gain

| Reset| 8x 01 04 0C 00 FF| ****

Gain     Setting

Up| 8x 01 04 0C 02 FF
Down| 8x 01 04 0C 03 FF
Command| Funnation| Command Packet| Note
---|---|---|---
 | Direct| 8x01040C00000p0qFF| pq: Gain     Positon    (o~ox0E)

CAM_Bright

| Reset| Bx 01 04 OD 00 FF| ****

Bright     Setting

Up| Bx 01 04 OD 02 FF
Down| Bx 01 04 OD 03 FF
Direct| 8x01044D00000p0qFF| pq: Bright I Positon       ()

CAM WDR

| On| Bx 01 04 3D 02 FF| ****

WDR ON/OFF

Off| Bx 01 04 3D 03 FF
Direct| Bx 01 04 D3 Op FF| pq: WDR Position    (1~ox06)

CAM_Backlight

| On| Bx 01 04 33 02 FF| Backlight On
Off| Bx 01 04 33 03 FF| Backlight Off

CAM_Aperture

| Reset| Bx 01 04 02 00 FF| ****

Aperture Control

Up| Bx 01 04 02 02 FF
Down| Bx 01 04 02 03 FF
Direct| 8x01044200000p0qFF| pq: Aperture Gain     (o~ox04)

CAM_Memory

| Reset| Bx 01 04 3F 00 Op FF| ****

p: Memory Number(=0 to 127) Corresponds to 0 to 9 on the Remote Commander

Set| Bx 01 04 3F 01 Op FF
Recall| Bx 01 04 3F 02 Op FF

CAM LR Reverse

| On| Bx 01 04 61 02 FF| ****

Image Flip Horizontal ON/OFF

Off| Bx 01 04 61 03 FF

CAM_PictureFlip

| On| Bx 01 04 66 02 FF| ****

Image Flip Vertical ON/OFF

Off| Bx 01 04 66 03 FF
CAM ColorGain| Direct| Bx 01 04 49 00 00 00 Op FF| (o~ox0E)
CAM 2D

Noise Reduction

| ****

Direct

| ****

Bx 01 04 53 Op FF

| 0:   OFF            1:   ON
CAM 3D

Noise Reduction

| Direct| Bx 01 04 54 Op FF| ****

0:OFF    1 :  AUTO         2~5 : LEVEL

FLICK

| 50HZ| 81 01 04 23 01 FF|
60HZ| 81 01 04 23 02 FF|

Freeze

| Freeze On| 81 01 04 62 02 FF| Freeze On Immediately
Freeze Off| 81 01 04 62 03 FF| Freeze Off Immediately
Preset Freeze On| 81 01 04 62 22 FF| Freeze On When Running Preset
Preset Freeze Off| 81 01 04 62 23 FF| Freeze Off When Running Preset

IR Transfer

| Transfer On| Bx 01 06 lA 02 FF| Receive IR(remote commander) CODE from VISCA communication ON/OFF
Transfer Off| Bx 01 06 lA 03 FF

Pan tiltDrive

| Up| Bx 01 06 01 VV WW 03 01 FF| VV: Pan speed 0x0l (low speed) to 0x18 (high speed)

WW: Tilt speed 0x0l (low speed) to

Down| Bx 01 06 01 VV WW 03 02 FF
Command| Funnation| Command Packet| Note
---|---|---|---
 | Left| 8x 01 06 01 VV WW 01 03 FF| 0x14 (high speed)

YYYY: Pan Position(TBD) ZZZZ: Tilt Position(TBD)

Right| 8x 01 06 01 VV WW 02 03 FF
Upleft| 8x 01 06 01 VV WW 01 01 FF
Upright| 8x 01 06 01 VV WW 02 01 FF
Downleft| 8x 01 06 01 VV WW 01 02 FF
DownRight| 8x 01 06 01 VV WW 02 02 FF
Stop| 8x 01 06 01 VV WW 03 03 FF

AbsolutePosition

| 8x 01 06 02 VV WW

0Y 0Y 0Y 0Y OZ OZ OZ OZ FF

RelativePosition

| 8x 01 06 03 VV WW

0Y 0Y 0Y 0Y OZ OZ OZ OZ FF

Home| 8x 0106 04 FF
Reset| 8x 010605 FF

Pan-tiltlimitSet

| ****

Set

| 8x 01 06 07 00 OW

0Y 0Y 0Y 0Y OZ OZ OZ OZ FF

| ****

W:1 UpRight     0:Downleft YYYY: Pan Limit Position(TBD) ZZZZ:  Tilt Limit Position(TBD)

Clear

| 8x 01 06 07 01 OW

07 OF OF OF 07 OF OF OF FF

Part3     Inquiry Command

CAM_Powerlnq

| ****

8x 09 04 00 FF

| y0 50 02 FF| On
y0 50 03 FF| Off(Standby)
CAM_ZoomPoslnq| 8x 09 04 47 FF| y0 50 Op 0q Or Os FF| pqrs: Zoom Position

CAM_FocusModelnq

| ****

8x 09 04 38 FF

| y0 50 02 FF| Auto Focus
y0 50 03 FF| Manual Focus
CAM_FocusPoslnq| 8x 09 04 48 FF| y0 50 Op 0q Or Os FF| pqrs: Focus Position

CAM_WBModelnq

| ****

8x 09 04 35 FF

| y0 50 00 FF| Auto
y0 50 01 FF| Indoor mode
y0 50 02 FF| Outdoor mode
y0 50 03 FF| OnePush mode
y0 50 04 FF| ATW
y0 50 05 FF| Manual
CAM_RGainlnq| 8x 09 04 43 FF| y0 50 00 00 Op 0q FF| pq: R Gain
CAM_BGainlnq| 8x 09 04 44 FF| y0 50 00 00 Op 0q FF| pq: B Gain

CAM_AEModel nq

| ****

8x 09 04 39 FF

| y0 50 00 FF| Full Auto
y0 50 03 FF| Manual
y0 50 0A FF| Shutter priority
y0 50 OB FF| Iris priority
y0 50 OD FF| Bright
CAM_ShutterPoslnq| 8x 09 04 4A FF| y0 50 00 00 Op 0q FF| pq: Shutter Position
CAM_IrisPoslnq| 8x 09 04 4B FF| y0 50 00 00 Op 0q FF| pq: Iris Position
CAMGainPosilnq| 8x 09 04 4C FF| y0 50 00 00 Op 0q FF| pq: Gain Position
CAM BrightPosilnq| 8x 09 04 4D FF| y0 50 00 00 Op 0q FF| pq:  Bright Position
CAM_ExpCompModelnq| 8x 09 04 3E FF| y0 50 02 FF| On
 |  | y0 50 03 FF| Off
---|---|---|---
CAM_ExpCompPoslnq| 8x 09 04 4E FF| y0 50 00 00 Op 0q FF| pq: ExpComp Position
CAM_Aperturelnq| 8x 09 04 42 FF| y0 50 00 00 Op 0q FF| pq: Aperture Gain
CAM_Memoryl nq| 8x 09 04 3F FF| y0 50pp FF| pp: Memory number last operated.
SYS_MenuModelnq| 8x 09 06 06 FF| y0 50 02 FF| On
 |  | y0 50 03 FF| Off
CAM_LR_Reverselnq| 8x 09 04 61 FF| y0 50 02 FF| On
 |  | y0 50 03 FF| Off
CAM_PictureFliplnq| 8x 09 04 66 FF| y0 50 02 FF| On
 |  | y0 50 03 FF| Off
CAM_IDlnq| 8x 09 04 22 FF| y0 50 Op 0q Or Os FF| pqrs: Camera ID

CAM_Versionlnq

| ****

8x 09 00 02 FF

| y0 50 ab cd

mn pq rs tu vw FF

|

IR Transfer

| ****

8x 09 06 lA FF

| y0 50 02 FF| On
y0 50 03 FF| Off
Pan-tiltMaxSpeedlnq| 8x 09 06 11 FF| y0 50 ww zz FF| ww:   PanMaxSpeed     zz: Tilt Max Speed

Pan-tiltPoslnq

| ****

8x 09 06 12 FF

| y0 50 Ow Ow Ow Ow

Oz Oz Oz Oz FF

| ****

wwww: PanPosition      zzzz: Tilt Position

VISCA PAN TILT ABSOLUTE POSITION VALUE

VISCA PAN TILT SPEED VALUE

Shutter speed

|  | 60/30mode| 50/25mode| ****

Iris

|  |
---|---|---|---|---|---|---
21| 1/10000| 1/10000| 0| close
20| 1/6000| 1/6000| 1| F14
19| 1/4000| 1/3500| 2| Fll
18| 1/3000| 1/2500| 3| F9.6
17| 1/2000| 1/1750| 4| F8
16| 1/1500| 1/1250| 5| F6.8
15| 1/1000| 1/1000| 6| F5 . 6
14| 1/725| 1/600| 7| F4.8
13| 1/500| 1/425| 8| F4
12| 1/350| 1/300| 9| F3.4
11| 1/250| 1/215| 10| F2.8
10| 1/180| 1/150| 11| F2.4
9| 1/125| 1/120| 12| F2
8| 1/100| 1/100| 13| Fl.6
7| 1/90| 1/75|  |
6| 1/60| 1/50|  |
5| 1/30| 1/25|  |
4| 1/15| 1/12|  |
3| 1/8| 1/6|  |  |
2| 1/4| 1/3|  |  |
1| 1/2| 1/2|  |  |
0| 1/1| 1/1|  |  |

Gain

| 0| 0dB|  | ****

Gain

| 8| 16dB
1| 2dB|  | 9| 18dB
2| 4dB|  | 10| 20dB
3| 6dB|  | 11| 22dB
4| 8dB|  | 12| 24dB
5| l0dB|  | 13| 26dB
6| 12dB|  | 14| 28dB
7| 14dB|  | 15| 30dB

IR TRANSFER(IR PASS)

1. Currently the camera support  NEC code     For customized with other codes, pls contact us.
2. Once the camera finish power configuration, enable the IR transfer function via sending COM command.
3. Get the targeted remote controller point to the camera IR receiver, press keys on the remote controller, then the camera will output the received IR code via VISCA IN

IR Transfer output format: The camera can save all setting, no need to re-set after power

OSD MENU

1. under working mode, press the menu button on the IR remote, to enter the OSD menu ; press the menu button again to exit and save modified parameter.
2. Use the navigate button to select the main menu. As above picture, once been selected, the main menu  will  change to grey color background, and the right side will show all parameters under this sub menu 
3. ln the second grade menu, press the up/down navigate button to select the sub menu, use left/right navigate button to set the parameter;
4. Select the last option “return” and press the right navigate button to get back to previous menu;
5. Press OSD button again to exit the menu.

CAMERA SET

| LANGUAGE| Chinese/English
---|---|---
PROTOCOL| VISCA/PELCO-P/PELCO-D
ADDRESS| 1~7
BAUD RATE| 2400,9600,115200
PARITY BIT| NONE
RETURN| Back to the main menu

FOCUS

| FOCUS MODE| AUTO/MANUAL/PUSH
---|---|---
SENSITIVITY| LOW/MIDDLE/HIGH
FOCUS LIMIT| 1.5M/2M/3M/6M/1OM
D ZOOM| OFF/ON
ZOOM SPEED| 0-7
LENS INIT| OFF/5K/10K/15K/20K/EXE
DIS ZOOM RATIO| OFF/ON
POSITION SAVE| OFF/SAVE
RETURN| Back to the main menu

WBMODE

| WB MODE| ATW/MANU/MANU2/SON./FL./AUTO/IDR./ODR./PUSH
---|---|---
B GAIN| 0~255    (Only Valid when WB MODE set to MANU)
R Gain| 0~255    (Only Valid when WB MODE set to MANU)
RETURN| Back to the main menu

EXPOSURE

| EXP MODE| AUTO/MANU/IRIS/SHUT/BRL
---|---|---
SHUT TIME| Shutter time: 1/1~1/10000      Only Valid when EXP MODE set to MANU
IRIS| Iris value: 0-13      Only Valid when EXP MODE set to MANU
AGC| Gain value:    0dB~15dB    Only Valid when EXP MODE set to MANU
BRIGHT| Brightness value: 0-27    Only Valid when EXP MODE set to BRI
SLOW SHUT| OFF/ON
FLICK| OFF/50HZ/60HZ
RETURN| Back to the main menu

PICTURE

| BRIGHTNESS| 0-15
---|---|---
SHARPNESS| 0-15
CONSTRAST| 0-15
SATURATION| 0-15
MIRROR| Image 180degree rotation left/right: OFF/ON
PIC FLIP| Image 180degree rotation up/down: OFF/ON
FREEZE| OFF/ON
DEFOG| OFF/1-15
RETURN| Back to the main menu

IMAGE ENHANCE

| 2DNR| OFF/ON ,
---|---|---
3DNR| OFF/AUTO/ 1-4
D WDR| OFF/1-6
GAMMA| 0-4
BACKLIGHT| OFF/ON
HIGHLIGHT| OFF/ON
RETURN| Back to the main menu

MASK

| MASK SWITCH| ON/OFF
---|---|---
COLOUR| WHITE/YELLOW/GRAY/GREENN IOLET/RED/
INDEX| 1-8
INDEX SWITCH| OFF/ON
ROW START| 0-1919
ROWEND| 1-1920
LINE START| 0-1079
LINE END| 1-1080
RETURN| Back to the main menu

D/NMODE

| D/NMODE| DAY/NIGHT/AUTO/
---|---|---
DAY TONIGHT| 15-200
NIGHT TODAY| 5-190
SWITCH DELAY| 1-60
GAIN LIMIT| 2-511
RETURN| Back to the main menu

CAMERA INF.

| IMAGE VER.| PC-V0.0.6    (changes without additional notices)
---|---|---
IMAGE DATE| 16.10.20      (changes without additional notices)
CONTROL VER.| UC V0.1.4 (changes without additional notices)
CONTROL DATE| 17.01.07 (changes without additional notices)
BAUDRATE| 9600
PARITY BIT| NONE
FRAMERATE| 1080P30
RETURN| Back to the main menu

UVC CONTROL

–                   –

4| Saturation Control| PU- SATURATION- CONTROL
5| Sharpness Control| PU- SHARPNESS- CONTROL
6| Gamma Control| PU GAMMA CONTROL

–                                  –

7| White Balance Temperature Control| PU- WHITE- BALANCE- TEMPERATURE- CONTROL
8| Gain Control| PU- GAIN- CONTROL
9| Power Line Frequency Control| PU- POWER- LINE- FREQUENCY- CONTROL
10| Zoom (Absolute) Control| CT-ZOOM-ABSOLUTE-CONTROL
11| Zoom (Relative) Control| CT- ZOOM- RELATIVE- CONTROL
12| PanTilt (Absolute) Control| CT PANTILT ABSOLUTE CONTROL

–           –              –

13| PanTilt (Relative) Control| CT- PANTILT- RELATIVE- CONTROL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>