Angekis U2-10FHD3 Camera Web Magazine User Manual

Angekis U2-10FHD3 Camera Web Magazine

Product Information

Product Usage Instructions

• Power Key: Under normal working mode, short press the Power key to let the camera enter standby mode. Press it again to trigger self-configuration and return to the HOME position. If a power on mode has been set, the camera will go to the preset position.
• Address/Camera Setting Key: Use the Set+Cam1-Cam4 keys to set the camera’s remote control address. Short press the Cam1 – Cam4 keys to select the camera.
• Number Key: Use the Set+(0-9) number keys to recall presets. Use the Clear +(0-9) keys to clear the relative preset. Long press to clear all presets.
• Menu Key: Press OK to confirm the menu selection. Press Menu to enter/exit the menu. Press Back to go back to the previous menu.
• F+/F-: Set focus manually. This is only valid under manual focus mode. Use T/W to set the lens zoom rate. Use the navigating keys (Up/Down/Left/Right) to set the pan tilt and select values when entering OSD.
• Home Key: Under normal working mode, short press the Home key to let the camera go back to the home position.
• Flip: Enable or disable the picture up/down flip. Use Mir to enable or disable the picture left/right flip. Use MF to enable manual focus mode. Use AF to enable auto focus mode.
• SHARP: Set the sharpness level. Use NR+/- to set the noise reduction level. Long press (3s) the Reset button to reset the camera. Use REV to display the camera revision.

SAFETY GUIDES

1. Before operating the camera, please read and follow all the instructions in the manual. For safety reasons, always keep this user manual close to the camera.
2. The Blade VS’s power input range is 100-240VAC (50-60Hz). Always ensure the power supply input is within this rate before turning it on.
3. The camera power voltage is 12VDC with a rated currency of 1.5A. We recommend that you use it with the original power supply adapter supplied by the factory.
4. Please keep the power cable, video cable and control cable in a safe place. Protect all cables especially the Connectors.
5. Operational environment: 0°C-50°C with humidity less than 90%. To avoid any danger, do not put anything inside the Camera and keep out from corrosive liquid.
6. Avoid stress, vibration and damp during transportation, storage and installation.
7. Do not detach the camera housing and cover. If there’s a need for service, contact your authorized technicians.
8. IR cable and control cable should be individually shielded and cannot be substituted with other cables. Do not direct the camera lens towards strong light (sun or intensive light).
9. Use a dry cloth to clean the camera housing. Apply it with a neutral cleaning agent to clean. To avoid damage on the camera lens, never use strong or abrasive cleaning agents on the camera housing.
10. Do not move the camera by holding the camera head. To avoid any mechanical issues, do not use your hands to rotate the camera head.
11. Place the camera on a fixed and smooth desk or base and avoid leaned Installation.
12. Power Supply Polarity (Drawing)

ACCESSORIES

Check all bellow items when open the package:

• Camera: 1 PCS
• Power Adapter: 1 PCS
• Power Cable: 1 PCS
• RS232 Control Cable: 1 PCS
• USB2.0 Cable; 1 PCS
• Remote Controller: 1 PCS
• User Manual: 1 PCS
• Double-sided Adhesive: 1 PCS

QUICK START

1. Ensure to check all cable connection before turning ii on

2. Dial Switch Setting (at the bottom of the camera):

FUNCTION ( ARM )

 | SW-1| SW-2| Instruction
 | OFF| OFF| Updating mode
2| ON| OFF| Debugging mode
3| OFF| ON| Undefined
4| ON| ON| Working mode
FUN CTION (IR CODE TYPE )

 | SW-3| SW-4| Instruction
 | OFF| OFF| Undefined
2| ON| OFF| Undefined
3| OFF| ON| Undefined
4| ON| ON| Undefined
FUNCTION (USB)

 | SW-5| SW-6| Instruction
 | OFF| OFF| Undefined
2| ON| OFF| Undefined
3| OFF| ON| Undefined
4| ON| ON| Undefined

PRODUCT HIGHLIGHTS

The New Blade VS delivers an amazing suite of features and maintains the beautiful optics you have come to expect from Angekis. Technical improvements and a class leading build quality compliment the Blades brilliantly sharp resolution and stunning colour reproduction, all at a ground-breaking price. Not only that, this stylish looking camera is ideal for cloud-based conferencing!

• 10x Optical zoom and 10x Digital zoom option
• Full HD resolution at 30fps via USB 2.0 Video format YUY2 and MJPG
• 1/2.8 inch, 5MP CMOS
• Rapid switching between different video formats: less than 1 second
• Easy firmware upgrade
• USB2.0 high speed output
• Compatible with the major videoconferencing software (UVC1 .5 protocol standard)
• 62.5° FOV and 350° pan rotation
• Visca over USB2.0, RS232 up to 128 pre-sets
• IR remote controller with 10 pre-sets
• Zoom Room remote Controller supported
• On screen NECC via custom Angekis app Video mute control
• Kensington lock hole
• 3D noise reduction
• Day/Night vision switch

PRODUCT SPECIFICATION

CAMERA INTERFACE

1. Camera Lens
2. Camera Base
3. IR Receiver Panel
4. indicator Light
5. Dial Switch
6. Tripod Screw Hole
7. Installation Hole
8. RS232(VISCA IN) Port
9. USB2.0 Port
10. DC12V Power Input
11. Power Indicator light

CAMERA DIMENSION(MM)

IR REMOTE CONTROLLER

• Power Key
  Under Normal working mode ， short press Power key to let the camera enter standby mode; Press it again ， the camera will do self-configuration and then go back to HOME position; It will go to preset position if the power on mode has been set.

• Address/Camera Setting Key

  • Set+（Cam1-Cam4）： set camera’s remote Control address.
  • Short press Cam1 – Cam4 to select the camera.

• Number Key
  Set Presets: Set+(0-9) number key to recall presets Clear Key

• Clear +(0-9): to clear the relative preset;
  Long press to clear all presets.

• Menu Key

  • OK: to confirm the menu selection
  • Menu: enter/exit menu
  • Back: Back to previous menu

• F+/F-:
  Set focus by manual, only valid under manual focus mode.

  • T/W: Set the lens zoom rate

  • Navigating Key: Up/Down/Left/Right
    Under normal working mode, use navigate key to set the pan tilt, and select values when enter OSD.

  • Home Key:
    Under normal working mode, short press Home key to let the camera go back to home position.

• Flip: Enable/Disable the picture up/down flip

• Mir: Enable/Disable the picture left/right flip

• MF: Enable manual focus mode

• AF: Enable auto focus mode

• SHARP: Set sharpness level

• NR+/-: Set noise reduction level

• Reset: Long Press(3S）to reset camera

• REV: Display camera revision

VISCA IN PORT

VISCA IN &RS485 Connection 

1           DTR
2           DSR
3           TXD
4| GND| GND
5           RXD
6| A(+)| A(+)
7           IROUT
8| B(-)| B(-)

VISCA IN &DB9 Connection 

Camera V ISCA

IN

| Windows DB -9
---|---
1| DTR| 6| DSR
2| DSR| 4| DTR
3| TXD| 2| RXD
4| GND| 5| GND
5| RXD| 3| TXD
6| A(+)|  |
7| IROUT|  |
8| B(-)|  |

SERIAL PORT CONFIGURATION:

VISCA PROTOCOL

Part1 Camera Return Command

Ack/Completion Message

 | Cornman

d package

|
 | Note

ACK| z0 41 FF| Returned when the command is accepted.
Completio

n

| z0 51 FF| Returned when the command has been executed.
 | Error Messages|
---|---|---
 |  | |  |
 |  | Note|
 | package|
Syntax Error| z0 60 02

FF

| Returned when the command format is different or when a command with illegal command parameters is accepted
Command Not Executable| z0 61 41

FF

| Returned when a command cannot be executed due to current conditions. For example, when commands controlling the focus manually are received during autofocus.

Part2 Camera Control Command

CAM_Power

| On| Bx 01 04 00 02 FF|

Power ON/OFF

Off| Bx 01 04 00 03 FF

Part 2 Camera Control CAM_Zoom

| Stop| Bx 01 04 07 00 FF|

c1\’/NM’Ji’/fard)

| Bx 01 04 07 02 FF
Wide(Standard)| Bx 01 04 07 03 FF
Tele(Variable)| Bx 01 04 07 2p FF|

p = 0(low)-7(high)

Wide(Variable)| Bx 01 04 07 3p FF
Direct| Bx 01| 04 47 Op 0q Or Os FF| pqrs: Zoom Position

-0x4000(tele))

| (0(wide)

CAM_Focus

| Stop| Bx 01 04 08 00 FF|
Far(Standard)| Bx 01 04 08 02 FF
Near(Standard)| Bx 01 04 08 03 FF
Direct| Bx 01| 04 48 Op 0q Or Os FF| pqrs: Focus Position
One Push AF| Bx 01 04 18 01 FF|

CAM_ZoomFocus

|

Direct

| Bx 01 04 47 Op 0q Or Os Ot Ou 0v Ow FF| pqrs: Zoom Position 0x4000(tele))

tuvw: Focus Position

| (0(wide)-

CAM_WB

| Auto| Bx 01 04 35 00 FF|
Indoor| Bx 01 04 35 01 FF|
Outdoor| Bx 01 04 35 02 FF|
 | OnePush| 8x 01 04 35 03 FF|
---|---|---|---
Manual| Sx 010435 05 FF|
Outdoor Auto| Sx 01 04 35 06 FF|
Sodium Lamp Auto| Sx 01 04 35 07 FF|
Sodium Auto| 8x 01 04 35 08 FF|

CAM_RGain

| Reset| Sx 01 04 03 00 FF|

Manual Control of R Gain

Up| Sx 01 04 03 02 FF
Down| Sx 01 04 03 03 FF
Direct| Sx 01 04 43 00 00 Op 0q

FF

| pq: R Gain (0-0xFF)

CAM_Bgain

| Reset| Sx 01 04 04 00 FF|

Manual Control of B Gain

Up| Sx 01 04 04 02 FF
Down| Sx 01 04 04 03 FF
Direct| Sx 01 04 44 00 00 Op 0q

FF

| pq: B Gain (0-0xFF)

CAM_AE

| Full Auto| Sx 01 04 39 00 FF| Automatic Exposure mode
Manual| 8x 01 04 39 03 FF| Manual Control mode
Bright| 8x 010439 OD FF| Bright mode(Manual control)

CAM_Shutter

| Reset| Sx 01 04 0A00 FF|

Shutter Setting

Up| Sx 01 04 0A02 FF
Down| Sx 01 04 0A03 FF
Direct| 8x01044A00000p0q FF| pq: Shutter Position (0-0x15)

CAM_lris

| Reset| Sx 01 04 OB 00 FF|

Iris Setting

Up| Sx 01 04 OB 02 FF
Down| Sx 01 04 OB 03 FF
Direct| Sx 01 04 4B 00 00 Op 0q

FF

| pq: Iris Position          (0-0x11)

CAM_Gain

| Reset| Sx 01 04 0C 00 FF|

Gain Setting

Up| Sx 01 04 0C 02 FF
Down| Sx 01 04 0C 03 FF
Direct| Sx 01 04 0C 00 00 Op 0q

FF

| pq: Gain Positon (0-0x0E)

CAM_Bright

| Reset| Sx 01 04 OD 00 FF|

Bright Setting

Up| Sx 01 04 OD 02 FF
Down| Sx 01 04 OD 03 FF
Direct| Sx 01 04 40 00 00 Op 0q

FF

| pq: Bright I Positon ()
CAM_WDR| On| Sx 01 04 30 02 FF| WDRON/OFF
 | Off| Bx 01 04 3D 03 FF|
---|---|---|---
Direct| Bx 01 04 D3 Op FF| pq: WDR Position (1- 0x06)

CAM_Backli ght

| On| Bx 01 04 33 02 FF| Backli ght On
Off| Bx 01 04 33 03 FF| Backli ght Off

CAM_Aperture

| Reset| Bx 01 04 02 00 FF|

Aperture Control

Up| Bx 01 04 02 02 FF
Down| Bx 01 04 02 03 FF
Direct| Bx 01 04 42 00 00 Op 0q FF| pq: Aperture Gain (0- 0x04)

CAM_Memory

| Reset| Bx 01 04 3F 00 Op FF|

p: Memory Number(=0 to 127) Corresponds to 0 to 9 on the Remote Commander

Set| Bx 01 04 3F 01 Op FF
Recall| Bx 01 04 3F 02 Op FF

CAM_LR_Reverse

| On| Bx 01 04 61 02 FF|

Image Flip Horizontal ON/OFF

Off| Bx 01 04 61 03 FF

CAM_PictureFlip

| On| Bx 01 04 66 02 FF|

Image Flip Vertical ON/OFF

Off| Bx 01 04 66 03 FF
CAM_ColorGain| Direct| Bx 01 04 49 00 00 00 Op FF| (0 ~0x0E)
CAM_2D

Noise Reduction

| Direct| Bx 01 04 53 Op FF| 0O OFF             10ON
CAM_3D

Noise Reduction

| Direct| Bx 01 04 54 Op FF| 0:OFF   10A UTO         2~5OLEVEL

FLICK

| 50HZ| 81 01 04 23 01 FF|
60HZ| 81 01 04 23 02 FF|

F reeze

| Freeze On| 81 01 04 62 02 FF| Freeze On Immediately
Freeze Off| 81 01 04 62 03 FF| Freeze Off Immediately
Preset Freeze On| 81 01 04 62 22 FF| Freeze On When Running Preset
Preset Freeze

Off

| 81 01 04 62 23 FF| Freeze Off When Running Preset

IR_Transfer

| Transfer On| Bx 01 061A02 FF| Receive IR(remote commander)

CODE from VISCAcommunication ON/OFF

Transfer Off| Bx 01 06 1A 03 FF

Pan_tiltDrive

| Up| 8x 01 06 01 W WW 03 01

FF

|

W: Pan speed 0x01 (low speed) to 0x18 (high speed)

WW: Tilt speed 0x01 (low speed) to 0x14 (high speed)

YYYY: Pan Position(TBD) ZZZZ: Tilt Position(TBD)

Down| 8x 01 06 01 WWW0302 FF
Left| 8x 01 06 01 W WW 01 03 FF
Right| 8×01 0601 WWW0203 FF
Upleft| Bx 01 06 01 WWW 01 01

FF

 | Bx 01 06 01 WWW 02 01
Upright| FF
 |
 | Downl eft| 8x 01 06 01 W WW 01 02 FF|
---|---|---|---
DownRight| 8×010601 WWW0202 FF
Stop| 8x 01 06 01 WWW 03 03

FF

AbsolutePositio

n

| 8x 010602 WWW

0Y 0Y 0Y 0Y OZ OZ OZ OZ FF

RelativePositio

n

| 8x 010603 WWW

0Y 0Y 0Y 0Y OZ OZ OZ OZ FF

Home| 8x 01 06 04 FF
Reset| 8x 01 06 05 FF

Pan-tiltlimitSet

|

Set

| 8x 01 06 07 00 OW

0Y 0Y 0Y 0Y OZ OZ OZ OZ FF

|

W: 1 UpRight 0:Downleft

=YY:YY: Pan Limit Position(TBD) Tilt Limit Position(TBD)

Clear

| 8x 01 06 07 01 OW

07 OF OF OF 07 OF OF OF

FF

Part3 Inquiry Command

**Command|  | Command**

Packet

|  | Return Packet| Note
---|---|---|---|---|---
CAM_Powerlnq| Bx 09 04 00 FF|  | y0 50 02 FF| On
 | y0 50 03 FF| Off(Standby)
CAM_ZoomPoslnq| 8x 09 04 47 FF| y0 50 Op 0q Or Os FF| pqrs: Zoom P osition
CAM_FocusModelnq| Bx 09 04 38 FF|  | y0 50 02 FF| Auto F oc us
 | y0 50 03 FF| Ma nual Focus
CAM_FocusPoslnq| Bx 09 04 48 FF| y0 50 Op 0q Or Os FF| pq r s : Focu s Position

CAM _WBModelnq

|

Bx 09 04 35 FF

|  | y0 50 00 FF| Auto
 | y0 50 01 FF| Indoor mode
 | y0 50 02 FF| Outdoor mode
 | y0 50 03 FF| OnePush mode
 | y0 50 04 FF| ATW
 | y0 50 05 FF| Manual
CAM_RGainlnq| 8x 09 04 43 FF| y0 50 00 00 Op 0q FF| pq: R Gain
CAM_BGainlnq| 8x 09 04 44 FF| y0 50 00 00 Op 0q FF| pq: B Gain

CAM_AEModelnq

|

8x 09 04 39 FF

|  | y0 50 00 FF| Full Auto
 | y0 50 03 FF| Manual
 | y0 50 0A FF| Shutter priority
 | y0 50 OB FF| Iris priority
 | y0 50 OD FF| Bright
CAM_ShutterPos lnq| Bx 09 04 4A FF| y0 50 00 00 Op 0q FF| pq: Shutter Position
CAM_lrisPoslnq| 8x 09 04 4B FF| y0 50 00 00 Op 0q FF| pq: Iri s Position
CAM_GainPosilnq| Bx 09 04 4C FF| y0 50 00 00 Op 0q

FF

| pq: Gain Position
---|---|---|---
CAM_ BrightPosilnq| Bx 09 04 4D FF| y0 50 00 00 Op 0q

FF

| pq: Bright Position
CAM_ExpCompMode l nq| Bx 09 04 3E FF| y0 50 02 FF| On
y0 50 03 FF| Off
CAM_ExpCo mpPosln

q

| Bx 09 04 4E FF| y0 50 00 00 Op 0q FF| pq: ExpComp Position
CAM_Aperturelnq| Bx 09 04 42 FF| y0 50 00 00 Op 0q FF| pq: Aperture Gain
CAM_Memorylnq| Bx 09 04 3F FF| y0 50pp FF| pp: Memory number last operated.
SYS_MenuModelnq| Bx 09 06 06 FF| y0 50 02 FF| On
 |  | y0 50 03 FF| Off
CAM_LR_Reverse lnq| Bx 09 04 61 FF| y0 50 02 FF| On
 |  | y0 50 03 FF| Off
CAM_PictureFliplnq| Bx 09 04 66 FF| y0 50 02 FF| On
 |  | y0 50 03 FF| Off
CAM_IDlnq| Bx 09 04 22 FF| y0 50 Op 0q Or Os FF| pqrs: Camera ID
CAM_Versionlnq| Bx 09 00 02 FF| y0 50 ab cd

mn pq rs tu vw FF

|
IR_Transfer| Bx 09 06 1A FF| y0 50 02 FF| On
y0 50 03 FF| Off
Pan-tiltMaxSpeedlnq| Bx 09 06 11 FF| y0 50 ww zz FF| ww: PanMaxSpeed zz: Tilt Max Speed
Pan-tiltPoslnq| Bx 09 06 12 FF| y0 50 Ow Ow Ow Ow

Oz Oz Oz Oz FF

| wwww: PanPosition zzzz: Tilt Position

VISCA PAN TILT ABSOL UTE POSITION VALUE

VISCA PAN TILT SPEED VALUE

Shutter speed

|  | 60/30mode| 50/25mode|

Iris

|  |
---|---|---|---|---|---|---
21| 1/10000| 1/10000| 0| close
20| 1/6000| 1/6000|  | F14
19| 1/4000| 1/3500| 2| F11
18| 1/3000| 1/2500| 3| F9.6
17| 1/2000| 1/1750| 4| F8
16| 1/1500| 1/1250| 5| F6.8
15| 1/1000| 1/1000| 6| F5.6
14| 1/725| 1/600| 7| F4.8
13| 1/500| 1/425| 8| F4
12| 1/350| 1/300| 9| F3.4
11| 1/250| 1/215| 10| F2.8
10| 1/180| 1/150| 11| F2.4
9| 1/125| 1/120| 12| F2
8| 1/100| 1/100| 13| F1.6
7| 1/90| 1/75|  |
6| 1/60| 1/50|  |
5| 1/30| 1/25|  |
4| 1/15| 1/12|  |
3| 1/8| 1/6|  |  |
2| 1/4| 1/3|  |  |
 | 1/2| 1/2|  |  |
0| 1/1| 1/1|  |  |

Gain

| 0| OdB|  |

Gain

| 8| 16dB
1| 2d8|  | 9| 18d8
2| 4d8|  | 10| 20d8
3| 6d8|  | 11| 22d8
4| 8d8|  | 12| 24d8
5| 10d8|  | 13| 26d8
6| 12d8|  | 14| 28d8
7| 14d8|  | 15| 30d8

PELCO-D PROTOCOL COMMAND LIST

Function|  | Byte1| Byte2| | |  |  |
---|---|---|---|---|---|---|---|---
 | Byte5|  |  | Byte6
 |  |
Up| 0xFF| Address| 0x00| 0x08| Pan Speed| Tilt Speed| SUM
Down| 0xFF| Address| 0x00| 0x10| Pan Speed| Tilt Speed| SUM
Left| 0xFF| Address| 0x00| 0x04| Pan Speed| Tilt Speed| SUM
Right| 0xFF| Address| 0x00| 0x02| Pan Speed| Tilt Speed| SUM
Upleft| 0xFF| Address| 0x00| 0x0C| Pan Speed| Tilt Speed| SUM
Upright| 0xFF| Address| 0x00| 0x0A| Pan Speed| Tilt Speed| SUM
DownLeft| 0xFF| Address| 0x00| 0x14| Pan Speed| Tilt Speed| SUM
DownRight| 0xFF| Address| 0x00| 0x12| Pan Speed| Tilt Speed| SUM
Zoom In| 0xFF| Address| 0x00| 0x20| 0x00| 0x00| SUM
Zoom Out| 0xFF| Address| 0x00| 0x40| 0x00| 0x00| SUM
Focus Far| 0xFF| Address| 0x00| 0x80| 0x00| 0x00| SUM
Focus Near| 0xFF| Address| 0x01| 0x00| 0x00| 0x00| SUM
Set Preset| 0xFF| Address| 0x00| 0x03| 0x00| Preset ID| SUM
Clear Preset| 0xFF| Address| 0x00| 0x05| 0x00| Preset ID| SUM
Call Preset| 0xFF| Address| 0x00| 0x07| 0x00| Preset ID| SUM
Query Pan Position| 0xFF| Address| 0x00| 0x51| 0x00| 0x00| SUM
Query Pan Position Response| 0xFF| Address| 0x00| 0x59| Value High Byte| Value Low Byte| SUM
Query Tilt Position| 0xFF| Address| 0x00| 0x53| 0x00| 0x00| SUM
Query Tilt Position Response| 0xFF| Address| 0x00| 0x5B| Value High Byte| Value Low Byte| SUM
Query Zoom Position| 0xFF| Address| 0x00| 0x55| 0x00| 0x00| SUM
Query Zoom Position Response| 0xFF| Address| 0x00| 0x5D| Value High Byte| Value Low Byte| SUM

PELCO-P PROTOCOL COMMAND LIST

Up| 0xA0| Addres s| 0x00| 0x08| Pan Speed| Tilt Speed| 0xAF| XOR
Down| 0xA0| Addres

s

| 0x00| 0x10| Pan

Speed

| Tilt

Speed

| 0xAF| XOR
Left| 0xA0| Addres s| 0x00| 0x04| Pan Speed| Tilt Speed| 0xAF| XOR
Right| 0xA0| Addres

s

| 0x00| 0x02| Pan

Speed

| Tilt

Speed

| 0xAF| XOR
Upleft| 0xA0| Addres s| 0x00| 0x0C| Pan Speed| Tilt Speed| 0xAF| XOR
Upright| 0xA0| Addres

s

| 0x00| 0x0A| Pan

Speed

| Tilt

Speed

| 0xAF| XOR
Downleft| 0xA0| Addres

s

| 0x00| 0x14| Pan

Speed

| Tilt

Speed

| 0xAF| XOR
DownRight| 0xA0| Addres s| 0x00| 0x12| Pan Speed| Tilt Speed| 0xAF| XOR
Zoom In| 0xA0| Addres s| 0x00| 0x20| 0x00| 0x00| 0xAF| XOR
Zoom Out| 0xA0| Addres s| 0x00| 0x40| 0x00| 0x00| 0xAF| XOR
Focus Far| 0xA0| Addres

s

| 0x00| 0x80| 0x00| 0x00| 0xAF| XOR
Focus Near| 0xA0| Addres s| 0x01| 0x00| 0x00| 0x00| 0xAF| XOR
Set Preset| 0xA0| Addres

s

| 0x00| 0x03| 0x00| Preset ID| 0xAF| XOR
Clear Preset| 0xA0| Addres s| 0x00| 0x05| 0x00| Preset ID| 0xAF| XOR
Call Preset| 0xA0| Addres s| 0x00| 0x07| 0x00| Preset ID| 0xAF| XOR
Query Pan Position| 0xA0| Addres

s

| 0x00| 0x51| 0x00| 0x00| 0xAF| XOR
Query Pan Position

Response

| ****

0xA0

| Addres s| ****

0x00

| ****

0x59

| Value High

Byte

| Value Low Byte| ****

0xAF

| ****

XOR

Query Tilt Position| 0xA0| Addres s| 0x00| 0x53| 0x00| 0x00| 0xAF| XOR
Query Tilt Position

Response

| ****

0xA0

| Addres s| ****

0x00

| ****

0x5B

| Value High

Byte

| Value Low Byte| ****

0xAF

| ****

XOR

Query Zoom Position| 0xA0| Addres s| 0x00| 0x55| 0x00| 0x00| 0xAF| XOR

OSD MENU

1. Under working mode, press the menu button on the IR remote, to enter the OSD menu; press the menu button again to exit and save modified parameters.

2. Use the navigate button to select the main menu. As above picture, once been selected, the main menu will change to grey color background, and the right side will show all parameters under this sub menu:

3. In the second grade menu, press the up/down navigate button to select the sub menu, use left/right navigate button to set the parameter;

4. Select the last option return and press the right navigate button to get back to previous menu;

5. Press OSD button again to exit the menu.

CAMERA SET

| LANGUAGE| Chinese/English
---|---|---
PROTOCOL| VISCA/PELCO-P/PELCO-D
ADDRESS| 1~7
BAUD RATE| 2400,9600,115200
PARITY BIT| NONE
RETURN| Back to the main menu

FOCUS

| FOCUS

MODE

| AUTO/MANUAL/PUSH
---|---|---
SENSITIVITY| LOW/MID/HIGH
FOCUS

LIMIT

| 1.5M/2M/3M/6M/10M
D_ZOOM| OFF/ON
ZOOM

SPEED

| 0-7
LENS INIT| OFF/51</10K/15K/20K/EXE
DIS ZOOM

RATIO

| OFF/ON
RETURN| Back to the main menu

WB MODE

| WBMODE| ATW/MANU/MANU2/SON./FL./AUTO/IDR./ODR /PUSH
B_GAIN| 0-255 (Only Valid when WB MODE set to MANU)
R_GAIN| 0-255 (Only Valid when WB MODE set to MANU)
RETURN| Back to the main menu

EXPOSURE

| EXP MODE| AUTO/MANU/IRIS/SHUT/BRL

SHUT TIME

| Shutter time: 1/1- 1/5000 Only Valid when EXP MODE

set to MANU

IRIS| Iris value: 0-13 Only Valid when EXP MODE set to

MANU

AGC| Gain value: 0dB-15dB Only Valid when EXP MODE

set to MANU

BRIGHT| Brightness value: 0-27 Only Valid when EXP MODE

set to BRI

SLOW SHUT| OFF/ON
FLICK| OFF/50HZ/60HZ
RETURN| Back to the main menu

PICTURE

| BRIGHTNES

s

| 1-15
SHARPNES

s

| 0-15
 | CONSTRAS

T

| 0-15
---|---|---
SATURATIO

N

| 0-14
MIRROR| Image 180degree rotation lefVright: OFF/ON
PIG FLIP| Image 180degree rotation up/down: OFF/ON
FREEZE| OFF/ON
DEFOG| OFF/1-15
RETURN| Back to the main menu

IMAGE ENHANCE

| 2D NR| OFF/ON’i
3D NR| OFF/AUTO/ 2-4
D_WDR| OFF/1-6
GAMMA| 0-4
BACKLIGHT| OFF/ON
HIGHLIGHT| OFF/ON
RETURN| Back to the main menu

MASK

| MASK

SWITCH

| ON/OFF
COLOUR| WHITE/YELLOW /GRAY/GREENN IOLET/RED/
INDEX| 1-8
INDEX

SWITCH

| OFF/ON
ROW START| 0-1919
ROW END| 1-1920
LINE START| 0-1079
LINE END| 1-1079
RETURN| Back to the main menu

D/N MODE

| D/N MODE| DAY/NIGHT /AUTO/EXT
DAY            TO

NIGHT

| 15-126
NIGHT       TO

DAY

| 5-190
 | SWITCH

DELAY

| 1-60
---|---|---
GAIN LIMIT| 2-511
RETURN| Back to the main menu

CAMERA INF.

| IMAGE VER.| PC-V0.0.6 (changes without additional notices)
IMAGE DATE| 16.10.20 (changes without additional notices)
CONTROL

VER.

| UC V0.1.4 (changes without additional notices)
CONTROL

DATE

| 17.01.07 (changes without additional notices)
BAUDRATE| 9600
PARITY BIT| NONE
FRAMERATE| 1080P30
RETURN| Back to the main menu

UVC CONTROL

White        Balance        Temperature

Control

| PU_WHITE _BALANCE_TEMPERATURE _CONTR

OL

Gain Control| PU_GAIN _CONTROL
Power Line Frequency Control| PU _PO W ER _LINE_FREQUENCY _CONTROL
Zoom (Absolute) Control| CT _ZOOM _ABSOLUTE_CONTROL
Zoom (Relative) Control| CT_ZOOM _RELATIVE_CONTROL
PanTilt (Absolute) Control| CT _PANTILT _ABSOLUTE _CONTROL
PanTilt (Relative) Control| CT _PANTILT _RELATIVE _CONTROL

FOR MORE INFO

Documents / Resources

| Angekis U2-10FHD3 Camera Web Magazine [pdf] User Manual
U2-10FHD3, U2-10FHD3 Camera Web Magazine, Camera Web Magazine, Web Magazine, Magazine
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>