UBTECH UKBTC01 Bluetooth Gaming Controller User Guide

UBTECH UKBTC01 Bluetooth Gaming Controller

Product Information

The product is a Bluetooth gamepad controller with the model name “UKBTC01” manufactured by UBTECH ROBOTICS CORP LTD. It operates at a temperature range of 0°C to 35°C and requires a 5V input with a frequency range of 2402MHz to 2480MHz. The maximum control distance is 10 meters in an open environment. The Bluetooth version used is 4.0, and it has a battery capacity of 550 mA.

Product Usage Instructions

1. To switch the main mode from the mode (L2+R2+Bluetooth button)
   • Ensure that the Bluetooth gamepad is not connected.
   • Press and hold the combination key (L2+R2+Bluetooth button) for 5 seconds.
   • After 5 seconds, the four indicator lights will flash rapidly.
   • Release the button to switch the Bluetooth gamepad to slave mode.
   • To switch back to the master mode, simply restart the handle.
2. To calibrate the joystick (L1+R1+Bluetooth button)
   • Ensure that the Bluetooth gamepad is not connected.
   • Press and hold the combination key (L1+R1+Bluetooth button) for 5 seconds.
   • After 5 seconds, the three red indicator lights will flash rapidly.
   • Release the button to initiate joystick calibration.
   • The joystick will rotate through 360 degrees, and the three indicator lights will turn off, indicating successful calibration.
3. To pair the Bluetooth controller
   • Long press the switch button to turn on the Bluetooth controller. The blue indicator light will start flashing slowly.
   • Hold the Bluetooth controller near the controller you want to pair with.
   • Long press the Bluetooth button until the blue indicator light starts flashing rapidly.
   • Release the Bluetooth button to establish a Bluetooth connection automatically.
   • A solid blue indicator light indicates a successful pairing.

Note : Please refer to the actual product for precise specifications and information. The provided guide is for reference only and does not constitute any form of commitment.

Global Preview

Introduction to buttons

Introduction to Bluetooth mode

1. Main mode (default mode)
   • Used for controlling robots.
2. From the mode
   • Used to control the stage mode of u Code programming software.

 Indicator light

Matching method
Main mode Bluetooth pairing

1. Long press the switch button to turn on the Bluetooth controller, and the blue indicator light starts flashing slowly.
2. Hold the Bluetooth controller near the controller you want to pair with, and then long press the Bluetooth button until the blue indicator light starts flashing rapidly. Release the Bluetooth button, and the Bluetooth connection will be established automatically. A solid blue indicator light indicates a successful pairing.

Combined keys

1. Switch the main mode from the mode (L2+R2+Bluetooth button)
   • The default state of the Bluetooth gamepad is the master mode. When the Bluetooth gamepad is not connected and the combination key (L2+R2+Bluetooth button) is pressed, after 5 seconds, the four indicator lights will flash rapidly.
   • Upon releasing the button, the Bluetooth gamepad switches to the slave mode.
   • To switch back to the master mode, simply restart the handle.
2. Joystick calibration button (L1+R1+Bluetooth button)
   • When the Bluetooth gamepad is not connected and the combination key (L1+R1+Bluetooth button) is pressed, after 5 seconds, the three red indicator lights will flash rapidly. Upon releasing the button, the joystick rotates through 360 degrees and the three indicator lights turn off, indicating successful calibration.

Specification and parameters

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.

1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions
2. This device may not cause harmful interference, and
3. this device must accept any interference received, including interference that may cause undesired operation.
4. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
5. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Note

• Please use a 5V adapter for charging.
• Please check the battery level before use and charge it in time, avoiding using it while charging.
• When using this product, keep away from fire sources and avoid charging or using it in extreme high or low temperature environments.
• Keep away from water sources and ensure the product is dry and clean.
• Do not attempt to disassemble this product without authorization.
• Please avoid placing this product on high or edge positions to prevent it from falling and damage.
• Machine damage caused by human error is not covered by our warranty.
• Please do not peel off the label on the back of the Bluetooth controller.

Scan the QR code to get the electronic quick guide
This guide does not constitute any form of commitment. Products (including but not limited to color, size, quantity, etc.), related information and pictures are for reference only.
Please refer to the actual product.

UBTECH ROBOTICS CORP LTD
Add: Room 2201, Building C1, Nanshan Smart Park, No.1001 Xueyuan Avenue, Changyuan Community, Taoyuan Street, Nanshan District, Shenzhen, PRC

• Web : www.ubtrobot.com

References

• Home Page-UBTECH

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>