Yale Z-Wave Plus Smart Module Installation Guide

Yale Z-Wave Plus Smart Module

Instruction

Adding a Yale Z-Wave Plus™ Smart Module to your Assure Lock & Z-Wave™ System
Please use this procedure only when the network primary controller is missing or otherwise inoperable

1. Install the Yale Smart Module into the slot above the battery compartment IMPORTANT: The batteries must be removed before removing the Yale Smart Module:
   • Remove battery cover
   • Remove batteries
   • Insert or remove Yale Smart Module
   • Reinstall batteries
   • Reinstall battery cover
2. Open the Z-Wave system’s smart home or alarm app on your smartphone or tablet
3. Follow the in-app instructions for adding a new device
4. On your lock keypad, enter your master entry code followed by the icon.
5.  Press the 7 key followed by the  icon.
6. Press the 1 key followed by the   icon.

Removing a Yale Z-Wave Plus Smart Module from your Assure Lock & Z-Wave System

1. On your lock keypad, enter your master entry code followed by the
2. Press the 7 key followed by the icon.
3.  Press the 3 key followed by the icon.
4. Open the Z-Wave system’s smart home or alarm app and follow the instructions for removing a device
5. Remove the Yale Smart Module from the slot above the battery compartment IMPORTANT: The batteries must be removed before removing the Yale Smart Module:
   • Remove battery cover
   • Remove batteries
   • Insert or remove Yale Smart Module
   • Reinstall batteries
   • Reinstall battery cover
6. If you’re adding a new Yale Smart Module, follow the instructions included with it

WARNING: Changes or modifications to this device, not expressly approved by Yale Home could void the user’s authority to operate the equipment.
This device is a security enabled Z-Wave Plus product that is able to use encrypted Z-Wave Plus messages to communicate to other security enabled Z-Wave Plus products. This device must be used in conjunction with a Security Enabled Z-Wave Controller in order to fully utilize all implemented functions. This product can be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.

FCC

Contain FCC ID: U4A-YRHCPZW0FM
Model: YRMZW2-US
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful Interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS.

1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
2. THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Feature Programming Through Menu Mode Using Master PIN code*

1. Touch screen with back of hand or palm to activate.

2. Enter 4-8 digit master PIN code* followed by key.
   Lock Response: “Menu mode, enter number (Enter digit corresponding to the function to be performed), press the key to continue.”

3. key to complete the process and conclude the programming session.

Determining Handing

Preparing Door

Preparing Door

Preparing Inside Escutcheon

Installing Latchbolt

Installing Outside Assembly

Installing Inside Support Assembly

Attaching Cables

Installing Inside Escutcheon

Installing Batteries & Cover

Programming Instructions

Creating Master PIN Code

Creating User PIN Codes

Creating User PIN Codes con’t

Locking & Unlocking Door with
Registered Master or User PIN Code

Locking Door with Privacy Button

Programming Troubleshooting

Lock does not respond – door is open and accessible.

| • Touchscreen becomes active when pressed w/whole hand. Use a larger area of the hand or fingers and verify contact with at least 3 areas.

• If touchscreen numbers are visible, check to see if they respond when pressed.

• Check batteries are installed and oriented correctly (polarity) in the battery case.

• Check batteries are in good condition; replace batteries if discharged.

• Check to see if touchscreen cable is fully connected and not pinched.

Lock does not respond – door is locked and inaccessible.| • Batteries may be completely discharged.

•  Apply 9V battery to terminals on the touchscreen for emergency power jump option.

Unit is on for a while then shows no reaction. Lights dim.| ****

•Batteries do not have enough power. Replace batteries.

Unit chimes to indicate code acceptance, but the door will not open.

| • Check for another locking device on the door (i.e. deadbolt).

• Check the door gaps for any foreign objects between door and frame.

• Check that the motor cable is firmly connected into the PC

board marked “MOTOR”.

Unit operates to allow access, but will not automatically re-lock.| • Check to see if Auto Re-lock Mode is enabled.

• If low battery indicator is lit (see below), change batteries.

PIN codes will not register.

| • PIN codes must consist of 4 to 8 digits to register.

• The same PIN code cannot be used for multiple users.

• Registration/management of PIN codes is set by the authority of the Master Code, which is set first.

• Contact the Master user.

• User codes must be entered within 20 seconds (while touchscreen is active) or process will have to be restarted.

• Check  or gear  cannot be used as part of the PIN code.

Upon entering a PIN code and pressing        key, the unit displays “invalid code” error or lock times out with- out responding.| • Check to see if All Code Lockout Mode is enabled.

• Only the Master can enable/disable Lockout Mode. Contact the Master user.

Upon entering a PIN code and pressing the        key, the red padlock icon appears

and there are different tones.

| • Check to see if All Code Lockout Mode is enabled.

• Only the Master can enable/disable Lockout Mode. Contact the Master user.

The unit operates, but it makes no sound.| • Check to see if Volume is set to Silent.
The unit responds “Low Battery”| • This is the alert to replace the batteries. Replace all four

(4) batteries with new AA Alkaline batteries.

Upon entering a PIN code and pressing the key, the unit responds “Wrong number of digits”.| • The digits entered were incorrect or incomplete. Re-enter 4-8 digits followed by the check  key.

Hardware Troubleshooting

Door is binding.

Latchbolt will not deadlock.

a. Either strike is out of alignment or the gap between door and jamb is too great. Realign strike or shim strike out towards flat area of latchbolt.

Latchbolt does not retract or extend properly. Latchbolt tail and retractor are not properly positioned:

a. Remove lockset. Look through 2-1/8″ hole and verify latchbolt tail is centered between top and bottom of hole.

b.  Remove latchbolt and insert lockset. Look through latchbolt hole and verify retractor mouth is centered in hole. If not, adjust outside rose plate.

c. If necessary, rebore holes to line up retractor and tail.

Cycle lock in both the locked and unlocked positions. If problems are found:

Factory Settings

*The Master PIN code must be registered prior to any other

Lever Removal Tool Hex Wrench
When lock is reset to factory defaults all user codes (including the Master PIN code*) are deleted and all programming features are reset to original default settings (see Factory Settings).
IMPORTANT: The outside assembly remains assembled.

1. Remove inside lever with the supplied lever removal tool.

2. Remove the battery cover with supplied hex wrench and then remove batteries.

3.  Remove the 10-32 x 3/4″ pan head screw from the center of the battery housing.

4. Remove the interior escutcheon  from the door to access the reset button on back of escutcheon. Cables may stay connected. (See illustration at above for location of the reset button.)

5. Reinstall four (4) AA batteries.

6. Press the reset button for 3 seconds.

7. While continuing to press the reset button, temporarily remove one (1) AA battery.

8. Reinstall the battery.

9. Release reset button and wait approximately 15 seconds. Speaker will announce
   “Welcome to Yale.”

10. Reassemble escutcheon by reversing steps 1-4.

Upon reset, Master PIN Code creation is the only option available and must be performed prior to any other programming of the lock. Please use this procedure only when the network primary controller is missing or otherwise inoperable.

Yale Z-Wave Plus Product Info

Manufacturer ID: Assa Abloy (0x0129)
Z-Wave Device Type: Door Lock Keypad
Z-Wave Role Type: Listening Sleeping Slave (LSS)

Product ID:

•  0x1200 for NTT610/620/630/640-ZW2 (Exit Device)
•  0x0C0C for NTT612-ZW2 (2nd Generation Touch Screen Exit Device)
•  0x0C16 for NTT622-ZW2 (2nd Generation Touch Screen Exit Device)

Product Type ID:

• 0x8009 for NTT610/630-ZW2 (Pushbutton Exit Device)
• 0x800A for NTT620/640-ZW2 (Touch Screen Exit Device)
• 0x8102 for NTT612/622-ZW2 (2nd Generation Exit Device)

Supported Command Classes

Command Class Z-Wave Plus Info Command Class Manufacturer Specific Command Class Security
Command Class Device Reset Locally Command Class Power Level
Command Class Version
Command Class Battery
Command Class Door Lock
Command Class Door Lock Logging Command Class Schedule Entry Lock Command Class User Code
Command Class Time Parameters Command Class Time
Command Class Association
Command Class Association Group Info Command Class Notification
Command Class Configuration Command Class Firmware Update Md * Command Class Requires Security

Association Table

1

| ****

1

| ****

Lifeline

| Command_Class_Battery, Battery_Report ; Command_Class_Notification, Notification_Report; Command_Class_Configuration, Configuration_Report; Command_Class_Device_reset_locally,

Device_Reset_locally_notification

Notifications Table

Alarm _Reports_

| _ _Alarm__ type| ****

Alarm _Level_

| ****

Description

---|---|---|---
Master Code changed.| ****

0x70

| 0x00| Master code was changed at keypad
0xFB| Master code was changed over RF
User added| 0x(01-max

users)

| User added. Alarm level = user slot number
User deleted| 0x21| 0x(01-max

users)

| User was deleted. Alarm level = user slot number
Tamper Alarm| 0xA1| 0x01| keypad attempts exceed code entry limit
0x02| front escutcheon removed from main
RF Operate Unlock| 0x19| 0x01| by RF module
Manual Unlock| 0x16| 0x01| By key cylinder or

inside thumb turn

Keypad Unlock| 0x13| 0x(01-max

users)

| Where Alarm level represents user slot number (0xFB =

Master Code)

Manual Lock

| ****

0x15

| 0x01| by key cylinder or inside thumb-turn
0x02| by touch function (lock and leave)
0x03| By inside button
RF Operate Lock| 0x18| 0x01| by RF module
Keypad Lock| 0x12| 0x (01 – max

users)

| Where Alarm level represents user slot number
Non Access| 0x26| 0x(01-max

users)

| A Non Access Code was entered at the lock.

Where alarm level represents user slot number

Jammed

| ****

0x09

| ****

0x01

| Jammed while locking

0x02

| Jammed while unlocking
Low Battery

Alarms**

| 0xA9| 0x (Current %)| Too Low to operate (Starting at 4.6V for 0x8009 &

0x800A ; 4.2V for 0x8102 )

| 0xA8| 0x (Current %)| Critical Battery Level (Starting at 4.8V for 0x8009 &

0x800A ; 4.4V for 0x8102 )

---|---|---|---
0xA7| 0x (Current %)| Low Battery

(Starting at 5V for 0x8009 & 0x800A ; 4.6V for 0x8102 )

Auto Lock Operate

Locked

| 0x1B| 0x01| Auto re-lock cycle complete, locked.

Duplicate Pin-code error

| ****

0x71

| ****

0x (01-max users)

| Where Alarm level represents user slot number Alarm generated in response to add user RF cmd. This alarm is not generated when attempting to add duplicate pin at the keypad. The lock simply denies it and plays the “Denied”. Trying to duplicate the

master code will result in a 0x71 0x00 alarm report.

RF Module Power Cycled| ****

0x82

| ****

0x00

| Power to RFM was restored, sent by RF module. The lock doesn’t send any alarm to the RF module when

power is cycled.

Disabled user entered at keypad| 0x83| 0x(01-max users)| A disabled user pin code was entered at the keypad

Valid user but outside of schedule

| ****

0x84

| ****

0x(01-max users)

| A valid user can be both a normal user and a Non- Access user. If a non- access user is out of schedule this alarm will be sent instead of the non- access alarm.

Door Position Sensor (Optional Hardware Required)

| ****

0x2B

| 0x00| Door Opened
0x01| Door Closed
0x02| Door Propped (Door Open for longer than configurable door propped time)
Daily Repeating Schedule

Set/Erased

| ****

0x60

| 0x(01-max users)| ****

Schedule(s) has been set/erased for specified user ID

Daily Repeating Schedule

Enabled/Disabled

| ****

0x61

| 0x(01-max users)| Schedule(s) has been enabled/disabled for specified user ID
Year Day Schedule

Set/Erased

| 0x62| 0x(01-max

users)

| Schedule(s) has been set/erased for specified user ID
Year Day Schedule Enabled/Disabled| 0x63| 0x(01-max users)| Schedule(s) has been enabled/disabled for specified user ID
All Schedule Types

Erased

| 0x64| 0x(01-max

users)

| Schedule(s) has been set/erased for specified user ID
All Schedule Types Enabled/Disabled| 0x65| 0x(01-max users)| Schedule(s) has been enable/disabled for specified user ID

** – The Yale NexTouch Exit Rim Trim locks also supports a 3rd low battery alarm, too low to operate.
This alarm is sent out as a Battery Report (with value = 0xFF) through the Battery Command Class. This is the last low battery alarm level before the product stops functioning.

_ _Configuration__ Parameters| _ _Parameter__ Number| _ _Size__| _ _Description__
---|---|---|---
Silent mode on/off| 1| 1 byte| Level control, 1 = High Volume, 2 = Low Volume, 3 = Silent.

Default is 2 or Low Volume

Auto Relock on/off| 2| 1 byte| 0x00 = OFF , 0xFF = ON default is 0x00 or OFF
Auto Relock time| 3| 1 byte| 10 to 180 seconds default is 30 seconds
Wrong Code Entry Limit| 4| 1 byte| 3 to 10 default is 5 times
Language| 5| 1 byte| 1=English, 2=Spanish, 3=French default is 1= English
Shut down time (after wrong code entries)| 7| 1 byte| 10 to 180 seconds default is 60 seconds

Operating mode

| ****

8

| ****

1 byte

| 00 = normal mode (this is the default mode)

01 = vacation mode, keypad lockout

02= privacy mode, no keypad. RF Unlock will work

One Touch Locking| 11| 1 byte| 0x00 = OFF, 0xFF = ON default is 0xFF or ON.
Privacy Button| 12| 1 byte| 0x00 = OFF, 0xFF = ON default is 0x00 or OFF
Lock Status LED| 13| 1 byte| 0x00 = OFF, 0xFF = ON default is 0x00 or OFF.

Reset To Factory Defaults

| ****

15

| ****

1 byte

| 01 = Lock will execute Reset To Factory.

No default value

Door Propped Timer***

| ****

18

| ****

1 byte

| 10 to 2540 second. This value is represented as seconds X 10. (ie a value of 4 would mean a door propped timer of 40 seconds) Set to 0x00 to disable Door Propped Alarm. Default

= 0x00 (off)

DPS Alarms***

| ****

19

| ****

1 byte

| 0x00 = OFF, 0xFF = ON Default is 0x00 or off.

Used to enable/disable door condition alarms for locks that support a door position sensor. Any lock that does not support DPS will always report 0x00.

Eco Mode On/Off| 21| ** 1 byte| 0x00 = OFF , 0xFF = ON default is 0x00 or OFF**

**** If supported switches lock to lower power mode of operation with reduced sound and led brightness.

*** – Additional hardware required. These parameters are only active if the optional Door Position Switch has been installed with the lock.

References

• Welcome to Yale - Trusted every day. | Yale

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>