KENWOOD X302-4 Class D Four Channel Power Amplifier Instruction Manual
- June 5, 2024
- KENWOOD
Table of Contents
X302-4
XM302-4
KAC-314
CLASS D FOUR CHANNEL POWER AMPLIFIER
INSTRUCTION MANUAL
AMPLIFICATEUR DE PUISSANCE 4 CANAUX CLASSE D
JVCKENOOD Corporstion
Accessoires
1| Ø4×16 mm
Self-tapping screws| 4| 2| Speaker level input cable| 1
---|---|---|---|---|---
Dimensions
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain
the best performance from your new power amplifier.
For your records
Record the serial number, found on the back of the unit, in the spaces
designated on the warranty card, and in the space provided below. Refer to the
model and serial numbers whenever you call upon your Kenwood dealer for
information or service on the product.
Model X302-4 / XM302-4 / KAC-314 Serial number
US Residents Only
Register Online
Register your Kenwood product at www.kenwood.com/usa
© 2021 JVCKENWOOD Corporation B5A-3477-10 / 01 (KN / WN)
Safety precautions
WARNING
To prevent injury or fire, take the following precautions:
- Mounting and wiring this product requires skills and experience. For safety’s sake, leave the mounting and wiring work to professionals.
- When extending the ignition, battery, or ground wires, make sure to use automotive-grade wires or other wires with the range of 5 mm 2 (AWG 10) or more to prevent wire deterioration and damage to the wire coating.
- To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit.
- If the unit starts to emit smoke or strange smells, turn off the power immediately and consult your KENWOOD dealer.
- Do not touch the unit during use because the surface of the unit becomes hot and may cause burns if touched.
CAUTION
To prevent damage to the machine, take the following precautions:
- Be sure the unit is connected to a 12 V DC power supply with a negative ground connection.
- Do not open the top or bottom covers of the unit.
- Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing.
- When replacing a fuse, only use a new one with the prescribed rating. Using a fuse with the wrong rating may cause your unit to malfunction.
- To prevent a short circuit when replacing a fuse, first disconnect the wiring harness.
NOTE
- If you experience problems during installation, consult your KENWOOD dealer.
- If the unit does not seem to be working right, consult your KENWOOD dealer.
Cleaning the unit
If the front panel gets dirty, turn off the power and wipe the panel with a
dry silicon cloth or soft cloth.
CAUTION
Do not wipe the panel with a hard cloth or a cloth dampened by volatile
solvents such as paint thinner and alcohol.
They can scratch the surface of the panel and/or cause the indicator letters
to peel off.
To prevent battery rise
When the unit is used in the ACC ON position without turning the engine ON, it
depletes the battery. Use it after starting the engine.
Protection function
The protection function is activated in the following situations:
This unit is equipped with a protection function for protecting this unit and
your speakers from various accidents or problems that can occur.
When the protection function is triggered, the power indicator goes off and
the amplifier stops operating.
- When a speaker wire may be short-circuited.
- When a speaker output contacts the ground.
- When the unit malfunctions and a DC signal is sent to the speaker output.
- When the internal temperature is high and the unit won’t operate.
Wiring
-
Take the battery wire for this unit directly from the battery.
If it’s connected to the vehicle’s wiring harness, it can cause blown fuses, etc. -
If a buzzing noise is heard from the speakers when the engine is running, connect a line noise filter (optional) to each of the battery wires.
-
Do not allow the wire to directly contact the edge of the iron plate by using Grommets.
-
Connect the ground wire to a metal part of the car chassis that acts as an electrical ground passing electricity to the battery‘s negative ⊖ terminal. Do not turn the power on if the ground wire is not connected.
-
Be sure to install a protective fuse in the power cord near the battery. The protective fuse should be the same capacity as the unit’s fuse capacity or somewhat larger.
-
For the power cord and ground, use a vehicle-type (fireproof ) power wring cord. (Use a power wiring cord with the range of 5 mm 2 (AWG 10) or more.)
-
When more than one power amplifier is going to be used, use a power supply wiring wire and protective fuse of greater current-handling capacity than the total maximum current drawn by each amplifier.
Speaker selection
- Using speakers with smaller input ratings than the amplifier’s output power would result in smoke gener- ation or equipment failure.
- The impedance of the speakers that are going to be connected should be 2 Ω or greater (for stereo connections), or 4 Ω or greater (for bridged connections).
When more than one set of speakers are going to be used, calculate the combined impedance of the speakers and then connect suitable speakers to the amplifier.
Installation
| 
---|---
NOTE After wiring, fix the protective cover securely with screws and
washers.
Installation procedure
Since there are large variety of settings and connections possible according
to applications, read the instruction manual well to select the proper setting
and connection.
- Remove the ignition key and disconnect the negative ⊖ terminal of the battery to prevent short circuits.
- Set the unit according to the intended usage.
- Remove the Dressing cover.
- Connect the input and output wires of the units.
- Connect the speaker wires.
- Connect the power wire, power control wire and grounding wire following this order.
- Install the installation fittings in the unit.
- Attach the unit.
- Attach the Dressing cover.
- Connect the negative ⊖ terminal of the battery.
CAUTION
- Do not install in the below locations; (Unstable location, In a location that interferes with driving, In a location that gets wet, In a dusty location, In a place that gets hot, In a place that gets direct sunlight, In a location that gets hit by hot air)
- Do not install the unit under the carpet. Otherwise, heat build-up occurs and the unit may be damaged.
- Install this unit in a location that allows heat to easily dissipate. Once installed, do not place any object on top of the unit.
- The surface temperature of the amplifier will become hot during use. Install the amplifier in a place where people, resins, and other substances that are sensitive to heat will not come into contact with it.
- When making a hole under a seat, inside the trunk, or somewhere else in the vehicle, check that there is nothing hazardous on the opposite side such as a gasoline tank, brake pipe, or wiring harness, and be careful not to cause scratches or other damage.
- Do not install near the dashboard, rear tray, or airbag safety parts.
- The installation to the vehicle should securely fasten the unit to a place in which it will not obstruct driving. If the unit comes off due to a shock and hits a person or safety part, it may cause injury or an accident.
- After installing the unit, check to make sure that electrical equipment such as the brake lamps, turn signal lamps and windshield wipers operate normally.
Connections
WARNINGRemove the ignition key and disconnect the negative⊖ terminal of
the battery to prevent short circuits.
In a computer-equipped vehicle, when you remove the⊖terminal of the battery,
the memory may disappear, or a defect may occur in the electrical system of
the vehicle. Consult your dealer for further details.
WARNING
Particular attention must be given to making good electrical contact at the
amplifier-output and speaker terminals.
Poor or loose connections can cause sparking or burning at the terminals
because of the very high power that the amplifier can deliver.
CAUTION
-
If the sound is not output normally, immediately turn the power off and check connections.
-
Be sure to turn the power off before changing the setting of any switch.
-
If the fuse blows, check wires for shorts, then replace the fuse with one of the same rating.
-
Check that no unconnected wires or connectors are touching the car body.
Do not remove caps from unconnected wires or connectors to prevent short circuits. -
Connect the speaker wires to appropriate speaker connectors separately. Sharing the negative wire of the speaker or grounding speaker wires to the metal body of the car can cause this unit to fail.
-
After installation, check that the brake lamps, turn signal lamps and windshield wipers work properly.
Power wire and speaker wire connection
Connections
RCA INPUT connection
Speaker-level input connections
NOTE
Do not connect cables and leads to both RCA cable input jacks and the speaker
level input terminals simultaneously, for this may cause malfunction or
damage.
Cable color of the connector
**A** A channel Left |
+White |
|---|
– White-Black
**A** A channel Right| + Gray
– Gray-Black
**B** B channel Left| ⊕ Green
⊖ Green-Black
**B**B channel Right| ⊕ Purple
⊖ Purple-Black
System examples
4-channel system
2-channel + Subwoofer system
For U.S.A.
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to com- ply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio /TV technician for help.
Supplier’s Declaration of Conformity
Trade Name: KENWOOD
Products: CLASS D FOUR CHANNEL POWER AMPLIFIER
Model Name: X302-4 / XM302-4 / KAC-314
Responsible Party: JVCKENWOOD USA CORPORATION
2201 East Dominguez Street, Long Beach, CA 90810, U.S.A.
PHONE: 310 639-9000
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED OPERATION.
Controls
**Hi-Res AUDIO** The product with this logo is conformed to the Hi-
Resolution Audio standard defined by the Japan Audio Society. This logo is
used under license from Japan Audio Society.
It is recommended that a car audio system should be configured with all
HighResolution Audio compatible products from player to speaker to enjoy its
high quality sound.
This is a 4-channel amplifier including 2 stereo amplifiers in a body. One
amplifier is referred to as amplifier A and the other is an amplifier
B. This unit is compatible with a large variety of systems by combining the
switches and functions described in the following.
-
Fuse (20 A×2)
NOTE
If you can’t find the specified capacity fuse at your store etc., consult your KENWOOD dealer. -
Battery terminal (POWER IN BATT.)
-
A power control terminal (P . CON)
Controls the unit ON/OFF. -
Ground terminal (GND)
-
SPEAKER OUTPUT terminals (A.ch/B.ch)
• Stereo connections:
When you wish to use the unit as a stereo amplifier, stereo connections are
used. The speakers to be connected should have an impedance of 2 Ω or greater.
When multiple speakers are to be connected, ensure that the combined impedance
is 2 Ω or greater for each channel.
• Bridged connections: When you wish to use the unit as ed to the high-output
amplifier, bridged connections are used. (Make connections to the LEFT
channel⊕and the RIGHT channel⊖ SPEAKER OUTPUT terminals.) The speakers to be
connected should have an impedance of 4 Ω or greater. When multiple speakers
are tobe connected, ensure that the combined impedance is 4 Ω or greater.
⑥SP LEVEL INPUT terminal
The output from the FACTORY-INSTALLED HEAD UNIT up to 50 can be input. The
power is turned on and off as the unit detects the input signal (SIGNAL
SENSING TURN-ON). Therefore it is not necessary to connect the power control
wire.
⑦LINE IN terminal (A.ch/B.ch)
⑧INPUT SENSITIVITY control (A.ch/B.ch)
Set this control according to the pre-output level of the HEAD UNIT connected
with this unit.
NOTE
For the pre-output level, refer to the “Specifications” in the instruction
manual of the HEAD UNIT.
⑨BASS BOOST LEVEL control (B.ch)
Sets the low-frequency level to be compensated.
⑩FILTER switch (A.ch/B.ch)
This switch allows applying high-pass or low-pass filtering to the speaker
outputs.
• HPF (High-Pass Filter) position:
The filter outputs the band of higher frequencies than the frequency set with
the “FILTER FREQUENCY” control.
• OFF position:
The entire bandwidth is output without filtering.
• LPF (Low-Pass Filter)
position: The filter outputs the band of lower frequencies than the frequency
set with the “FILTER FREQUENCY” control.
⑪FILTER FREQUENCY control (A.ch/B.ch)
Sets the cutoff frequency when the “FILTER” switch is set to “HPF” or “LPF” .
⑫Power indicator
When the power is turned on, the Power indicator lights.
Troubleshooting Guide
What might appear to be a malfunction in your unit may just be the result of
slight misoperation or miswiring.
Before calling the service, first, check the following table for possible
problems.
| PROBLEM | POSSIBLE CAUSE | SOLUTION |
|---|
No sound.
(No sound from one side.)
(Blown fuse.)| •Input (or output) cables are disconnected.
•Protection circuit may be activated.
•Volume is too high.
•The speaker cord is shorted.| •Connect the input (or output) cables.
•Check connections by referring to the “Protection function’:
•Replace the fuse and use a lower volume.
•After checking the speaker cord and fixing the cause of the short, replace
the fuse.
The output level is too small (or too large).| •The input sensitivity
adjusting control is not set to the correct position.| •Adjust the control
correctly referring to”Controls
The sound quality is bad.
(The sound is distorted.)| •The speaker’s wires are connected with the wrong
+/- polarity.
•A speaker wire is pinched by a screw in the car body.
•The switches may be set improperly.| •Connect them properly checking the +/-
of the terminals and wires well.
•Connect the speaker wire again so that it is not pinched by anything.
•Set switches properly by referring to “Controls’:
Specifications
Specifications subject to change without notice.
Audio section
Rated power output (+B = 14.4 V)
Stereo (4 Ω)……………… 50 W × 4 (20 Hz–20 kHz, ≤ 1.0% THD)
Stereo (2 Ω)……………………………….75 W × 4 (1 kHz, ≤ 1.0% THD)
Bridged (4 Ω)…………………………. 150 W × 2 (1 kHz, ≤ 1.0% THD)
Speaker impedance………………………..4 Ω (2 Ω to 8 Ω allowable)
(Bridged connection: 4 Ω to 8 Ω allowable)
Frequency response (+0, −3 dB)…………………………20 Hz–50 kHz
Input sensitivity (RCA)……………………………………………………0.2 V–5.0 V
Signal to noise ratio……………………………………………………………….100 dB
Input impedance…………………………………………………………………….. 10 kΩ
Low pass filter frequency (−12 dB / oct.) …………………………………………………………..50 Hz–200 Hz
(variable)
High pass filter frequency (−12 dB / oct.) …………………………………………………………..50 Hz–200
Hz (variable)
Bass boost control (40 Hz / B channel) ………………………………………………………………….0 – +18 dB
(variable)
General
Operating voltage…………………………………………12 V DC car battery
Current consumption………………………………………………………………. 20 A
Dimensions (W×H×D)……………………………….213 × 53 × 149 mm 8-3/8 × 2-1/16 × 5-7/8 inch
Weight………………………………………………………………………….1.4 kg (3.1 lbs)
50 Watts RMS × 4 at 4 Ohms and ≤ 1% THD+N 85 dBA (Reference: 1 Watt into 4
Ohms)
For Europ
**X302-4 only /
Declaration of Conformity with regard to the EMC Directive 2014/30/EU
Declaration of Conformity with regard to the RoHS Directive 2011/65/EU
Manufacturer:
JVCKENWOOD Corporation
3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi, Kanagawa, 221-0022, JAPAN
EU Representative:
JVCKENWOOD Europe B.V.
Amsterdamseweg 37, 1422 AC Uithoorn, THE NETHERLANDS
X302-4 only / X302-4 uniquement /
X302-4 Solamente
Declaration of Conformity with regard to the Electromagnetic Compatibility
Regulations 2016 (S.I. 2016/1091)
Declaration of Conformity with regard to the Restriction of the Use of
Certain HazardousSubstances in Electrical and Electronic Equipment Regulations
2012 (S.I. 2012/3032)
Manufacturer:
JVCKENWOOD Corporation
3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi, Kanagawa, 221-0022, JAPAN
UK Importer:**
JVCKENWOOD U.K. Limited
First Floor, Gleneagles, the Belfry, Colonial Way, Watford, Hertfordshire WD24
4WH, UNITED KINGDOM
Information on Disposal of Old Electrical and Electronic Equipment (applicable
for countries that have adopted separate waste collection systems)
Products with the symbol (crossed-out wheeled bin) cannot be disposed of as
household waste.
Old electrical and electronic equipment should be recycled at a facility
capable of handling these items and their waste byproducts. Contact your local
authority for details in locating a recycle facility nearest to you. Proper
recycling and waste disposal will help conserve resources whilst preventing
detrimental effects on our health and the environment.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>