SHOKZ S661 OpenMove Bone Conduction Open Ear Sport Headphones User Guide
- June 5, 2024
- SHOKZ
Table of Contents
OPENMOVE S661
User Guide
How It Works
Headphone Controls
ON/OFF
Turn on the headphones：
Press and hold the Power/Volume + Button until the LED Indicator flashes blue.
Audrey will say： “Welcome to Shokz”
Turn off the headphones：
Press and hold the Power/Volume + Button until the LED Indicator flashes red.
Audrey will say： “Power off”
Pairing
- Start with OpenMove turned off.
- Press and hold the Volume + Button until the LED Indicator flashes red and blue alternately.
- Open your device’s Bluetooth settings and select ” OpenMove by Shokz.” Audrey will say “connected.”
How to Wear
Pick up the headphones, bring them behind the back of the base of your
neck, position the ear hooks on your ears, then enjoy your music!
*Wearing your headphones the wrong way could cause discomfort. The transducers should rest in front of your ears.
Volume
Operate volume controls while audio is playing.
How to change volume:
While your audio is playing, adjust headphone volume by pushing either the
Volume + or Volume ‒ buttons.
Listening with headphones at a high volume may affect your hearing and the audio will be distorted.
A “beep” will sound when the volume is at its max.
Multifunction Button
| Play/pause music
Click once
---|---
| Answer call
Click once
| Next song
Double-click while music is playing
| End call
Click once
| Previous song
Triple-click while music is playing
Multifunction Button
| Play music | Click once |
|---|---|
| Pause music | Click once |
| Next song | Double-click while music is playing |
| Previous song | Triple-click while music is playing |
| Switch language | Double-click while pairing |
| Answer call | Click once |
| End call | Click once during a call |
| Answer call waiting and end the current call | Press and hold for 2 seconds |
when receiving a second call
Ignore a call| Press and hold for 2 seconds during an incoming call
Activate voice assistant| Press and hold for 2 seconds when the device is on
standby
Redial last number| Double-click on standby
*Only applicable for phone calls, not online calls
Check Battery Status
Operate controls while audio is not playing
How to check battery status：
Click the Volume + or Volume – button while music is paused, Audrey will tell
you the battery status:
- “Battery high/Battery medium/Battery low/Charge me”
Extra Features
EQ Modes
Standard Mode：
Balanced frequency for listening to music
Vocal Booster Mode：
Enhanced intermediate frequencies for audiobooks, podcasts, etc.
Switching EQ Modes
Operate controls while music is playing
How to switch EQ mode：
Press and hold both buttons （Power/Volume + Button and Volume – Button）while
music is playing until you hear a beep.
*Audrey will say： “Standard Mode/Vocal Booster Mode.”
Multipoint Pairing
Switch between two devices
seamlessly with multipoint pairing Pair Two Devices
Multipoint Pairing
Operate controls with headphones powered off
- Start with your headphones powered off.
- Press and hold Volume + until Audrey will say “pairing” and the LED indicator flashes red and blue alternately.
Audrey will say “multipoint enabled.” - Press and hold the multifunction button and Volume + button until Audrey says “multipoint enabled.”
Audrey will say “connected”. - Open first device’s Bluetooth® menu and select “OpenMove by Shokz.”Audrey will say “connected”.
- Turn your headphones off.
Audrey will say “connected”. - Re-enter pairing mode by pressing and holding Volume + until Audrey says “pairing” and the LED indicator flashes red and blue alternately.
- Open the second device’s Bluetooth® menu and select “OpenMove by Shokz.”Audrey will say “connected.”
- Turn your headphones off.
You will hear a beep, then Audrey will say “Welcome to Shokz, connected. The second device connected.” - Turn your headphones on. Your headphones are now connected to both devices.
Turn Multipoint Pairing Off
Operate controls with headphones powered off.
- Start with your headphones powered off.
- Press and hold Volume + until Audrey will say “pairing” and the LED indicator flashes red and blue alternately.
- Press and hold the multifunction button and Volume – button until Audrey will say “multipoint disabled.”
Restore Factory Settings
Operate controls with headphones powered off.
- Start with your headphones powered off.
- Press and hold Volume + until Audrey will say “pairing.” and the LED indicator flashes red and blue alternately.
- Press and hold the multifunction button, Volume ‒ button, and Volume + button until hearing two beeps and feel the vibration.
- Turn your headphones off. OpenMove is now reset and can be re-paired to your device.
Changing Languages
Your headphones have four built-in languages:
Chinese, English, Japanese and Korean.
Follow the instruction when headphones are powered off
- Start with your headphones powered off.
- Press and hold Volume + until Audrey will say “pairing” and the LED indicator flashes red and blue alternately.
- Double-press the multifunction button. Languages have been switched when you hear the corresponding language.
Care and Maintenance
Charging Tips
The headset will automatically shut down when charging
When the headphones are at low battery, there will be a “charge me” prompt and
the red light will flash intermittently. Use the corresponding USB-C cable for
charging.
The LED indicator will turn red during the charging process and the headphones
will automatically turn off. The LED indicator will turn from red to blue when
charging is complete.
Storage and Maintenance
-
Store the headphones in a cool, dry place. The working temperature should be 0~45°C(32~113°F). Working in a cold/hot temperature, highly humid area, or low air pressure environment may reduce the battery life.
-
Keep the product away from heat sources, direct sunlight, combustible gas, or other liquids.
-
Keeping the charging port dry before connecting to the charger will reduce the risk of damage.
-
These headphones are water-resistant but are not waterproof.
Please do not submerse the headphones in water. -
Clean the headphones with a soft dry cloth.
-
Do not charge right after exercising, in case there’s sweat inside the charging port, which could lead to circuit burning while charging.
-
After storage for a long period, please charge the headphones before using them again.
Note
Design and specification are subject to change without notice. For the most up-
to-date product information, please visit https://shokz.com.
Warning
To avoid the risk of explosion, fire, or leakage from toxic chemicals, please
do not disassemble the product or replace, deform, or mutilate the battery.
Warranty
Your headphones are covered by a warranty.
Visit our website at https://shokz.com/pages/warranty-landing for details of
the limited warranty.
*Failure to register will not affect your limited warranty rights.
Troubleshooting
If you have any trouble or problems, please visit https://shokz.com/pages/faq for more support!
What’s in the Box
If any part of your product is damaged or missing, do not use it.
Contact authorized Shokz dealer or Shokz customer service.
*Please note that the packaging envelope may vary depending on the sales region.
Regulatory and Legal Information
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC/IC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This
equipment has very low levels of RF energy that is deemed to comply without
testing of specific absorption rate (SAR).
Responsible party (contact for FCC matters only): AfterShokz LLC.
3200 Gracie Kiltz Lane, Suite 400 Austin, TX 78758 USA https://shokz.com
Industry Canada
This device complies with Industry Canada licence-exempt RSS standard(s):
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
CE Declaration of Conformity
Shokz Holding Limited hereby declares that this product is in compliance with
the essential requirements and other relevant provisions of Directive
2014/53/EU and all other applicable EU Directive requirements. The complete
declaration of conformity can be found at:
https://shokz.com/pages/policies. Shokz’s EU representative is AfterShokz
Euro B.V., Schipholweg 103, 2316XC Leiden, Netherlands.
| Frequency Range | Max. Transmit Power |
|---|---|
| 2400-2483.5MHz | 1dBm(EIRP) |
UK Declaration of Conformity
Shokz Holding Limited hereby declares that this product is in compliance with
the essential requirements and all other applicable United Kingdom
regulations. The complete declaration of conformity can be found at:
https://shokz.com/pages/policies.
Shokz’s authorized representative in the UK is Pinpoint Consumer Electronics
Ltd., Unit 35, Meridian House, Road One, Winsford Industrial Estate, Winsford,
Cheshire CW7 3QG.
WEEE Declaration of Conformity
This WEEE logo means that this product must not be discarded as household
waste, and should be delivered to an appropriate collection facility for
recycling. Proper disposal and recycling help protect natural resources, human
health, and the environment. For more information on the disposal and
recycling of this product, contact your local municipality, disposal service,
or the shop where you bought this product.
| Australia/New Zealand | Singapore | Philippines |
|---|
