THE HOME DEPOT Cesicia26 Ceiling Fan User Manual
- June 5, 2024
- THE HOME DEPOT
Table of Contents
THE HOMEDEPOT Cesicia26 Ceiling Fan
Packing List
Specification
Product Care
- Please read the manual before installation.
- Do not use this product in a humid environment or at high temperatures.
- If the ceiling fan is defective or breaks down, please stop using it and contact us with documented photos or short videos via dolorespriestleypp@outlook.com.
Installation
Note: Before installing the ceiling fan, make sure that the power has been turned off.
-
Tools ready
Philips screwdriver| Blade screwdriver | Adjustable pliers or wrench Step ladder/ Wire cutter/Electrical tape/ Impact drill
-
Installation of bracket
-
To use wood screws to fix brackets for wooden or false ceiling
-
To use expansion screws to fin bracket for concrete ceiling before that will need to drill dia.8mmexpansion bolts.
-
Install the blades
-
Install the fan blades to the motor in order and screw on the fan blade screws in turn.(Figure 2)
-
Install the boom safety pin to the junction of the boom and the hanger.(Figure 1)
-
Lamp installation
-
Connect the corresponding wires at the bottom of the lamp and the motor.
-
Tighten the three screws on the edge of the switch cover
-
Take out the decorative nuts,nuts,iron washers and plastic washers pre-locked on the lamp tube
-
Install glass, tighten plastic washer, iron washer and nut in turn
-
Install the decorative frame and fasten the decorative nut
-
Installation of download canopy and decorative
cover Selection of download -
To select the correct download. either 5 inches or 10 inches according to the ceiling height.Put the canopy and decorative cover through the download;
-
Remove the locking pin and the long pin. then remove the two downLoad set screws;
-
Fix the download set into the fan body and lock the download to the fan body with set screws.
-
Mount the bracket onto the outlet box by the screws, spring washers and flat washers.
-
Hang the ball joint and the fan onto the bracket and make sure the guide pin of the bracket is fitted into the slot of ball joint.
-
Insert the remote control receiver between the bracket and the download.
-
Connect wires from the supply and the bracket to the wiring terminals.
-
Attached canopy to the bracket by aligning canopy holes with the bracket holes Fix the canopy to bracket with set screWs.
-
Install the blade brackets and blades with screws.
-
Installation height
Fan blades to the ground shall note less than 2.3 meters
-
Hanging ceiling fan
-
Place the lobes in the hanger and turn the pipe so that the groove on the lobes engages thelugs on the dome(inside the hanger) The lug groove must engage the hanger lug.
-
Connect the power cord
Connect the remote control driver as shown in the picture (the driver is finally placed in the mounting bracket).
-
The balance adjustment of the fan
Fan is installed if it shakes up and down, please check the screws in the blades, download, and the lamp kit if they are fixed if not, please fix it with a screw driver If it still shakes, please use the balancing kit stools and check the instruction of balancing kit inside the carton.
Instruction of the remote control
- Turn off allloads.
- Fan speed control
- LED indicator light.
- Turn on the light/ Color
- Temperature Adjustment.
- Fan off.
- Fan positive and negative
- rotation control.
- Fan timing control.
- The remote control USES
- pair of 1.5v batteries.
- Natural Wind.
Tips:
- The remote control and receiver are paired as learning codes. The remote control is turned to receive the controller within one minute after the receiver is powered on; Long press the natural wind button about 5 seconds, in the sound of a drop, that learning success, can be used normally:(note: no learning is accepted if the power is energized for more than one minute)
- When the remote control cannot control the controller, please check whether the battery is loadet correctly,
- Too low battery voltage will affect the remote control distance and may cause remote control failure Please replace the battery in time
- When not in use for a long time, please remove the battery of the remote control;
- support the maximum 300VV lighting6. During installation, the ceiling cover of the fan shall not compress all the wires, which may easily cause the wires to break and short circuit
Function Description
Frequently asked questions (FA)
Q The fan/light/remote do not work?
A: 1. Ensure correct installation; 2. Check if the wiring terminal is in poor
contact, try to pull and plug again to ensure that the wires are connected
properly; 3. Check the batteries of the remote control; 4. Try pairing the
remote controller: press the button “OFF” (you’ll hear a “beep”), long-press
the button pair code’, you’ll here 2 “beep, which means that you have
successfully paired the fan. If there is no 2 “beep, press the button “OFF”,
turn off the machine forl minute, and then try again.
Q: When the fan is on it makes a loud noise. Any ideas why?
A: 1. The noise might be caused by magnet debris generated during
transportation, which could be attracted by the attached magnetic parts after
the fan working for about 10 minutes. Therefore, in order to eliminate the
noise, please try running the fan for about 10 minutes and see if the loud
sound disappears. 2. There might be some screws left in the shell in the
installation. Therefore, try to remove the lampshade, light source and
chassis, turn the fan by hand, shake out the screws, and the sOund can
disappear.
If you try the above tips and the fan still makes a loud noise, we will
replace it for you immediately. Sorry for the inconvenience.
Q:I installed this fan, and there is a 1 or 2 second remote delay. Why?
A: Because there is a motor protection program. When the power is supplied,
the receiver tests whether the motor matches it, and then works to start the
fan. This is to protect the motor and make it more durable
Q: Screw holes in mounting bracket do not match electrical box. Any advice?
A: The hole position is the computer digital punching, not the manual
punching, so it is accurate in principle. However, there is an important tip
in installation: You should fix all the screws into holes SLIGHTLY one by one,
and then screws all the holes tightly. Otherwise the screws might not match
with the holes accurately.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>