EASYLINE PFD20 Built in Induction Plates Instructions
- June 3, 2024
- EASYLINE
Table of Contents
EASYLINE PFD20 Built in Induction Plates Instructions
CAUTIONS
- Read all instruction carefully and keep the manual for future reference.
- Make sure that voltage on the appliance rating label corresponds to that of the power supply. (220-240V, 50/60Hz)
- Do not place the appliance near hot or humid area.
- Do not share socket with other appliances.
- To avoid overheat of the appliance, place the appliance on a steady and well ventilated area.
- To avoid injury, do not touch the stove top during and shortly after operation.
- To avoid accident, do not place appliance on any metallic top.
- To achieve a better result, our company’s cooking utensils are recommended.
- Do not bend or pull the power cord excessively.
- To avoid damaging the appliance, do not immerse the appliance into water.
- To avoid damaging the appliance, do not block the ventilation system.
- Do not place metallic objects lids, cans and aluminum foils on the stove top while operating.
- Do not place the appliance near any flammable, explosive and chemical materials.
- Do not place the appliance near any magnetic material.
- Do not plug or unplug with wet hands
- Do not place heavy or over load object on the stove top.
- To avoid auto switch off, do not place a sheet of newspaper or plastic tablecloth underneath the induction cooker, it may block the ventilation system of the appliance.
- Do not operate the appliance with a crack on the stove-top. Return appliance to the repairing center for examination or repair.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Make sure children do not play with the appliance.
- Do not operate any appliance with damage or malfunctioned. Contact the supplier or the service center for repair.
- If the power cord or plug is damaged, stop using it immediately. It must be checked or repaired by the manufacturer or the appointed service center.
- Children should be supervised to ensure that they do not play with the appliance.
- If the product is not in use for a long time, please switch the power off and unplug it.
SELECTION OF COOKING UTENSILS
To achieve the optimum cooking performance, it is suggested to use the given ferromagnetic pot. Or use the appropriate cooking utensils with ferromagnetic material, and flat bottom with diameter within 12-26cm. Please see the below diagram for reference:
Ferromagnetic Frying Pan
|
Ferromagnetic Stainless steel Pot
|
Ferromagnetic Flat buttom Pan
|
Ferromagnetic Kettle
| Suitable Pot
---|---|---|---|---
Ferromagnetic Sauce
Pan
|
Ferromagnetic Pot
|
Ferromagnetic Plate
|
Ferromagnetic Grill Pan
Aluminum Pot
|
Ceramic Pot
|
Glass Pot
|
Pot with Stands
| Non-Suitable Pot
Round Buttom Wok
|
Pot’buttom diameter less than 12cm
|
Pot with non-flat
buttom
|
Oval Buttom Pot
Product Description
- glass plate
- top plastic frame
- sensor
- heating coil
- control panel
- mainboard
- fan
- plug cord
- bottom plastic housing
- foot
CONTROL PANEL
OPERATING INSTRUCTION
Note: After pressing ON/OFF button, the induction cooker will shut off automatically if there is no any operation within 2 hours.
-
“ON/OFF” switch
Connect power plug. A “beep” sound is heard. All indicator light will be flash once, which represent the induction cooker is under “standby mode”. Press the “ON/OFF” button, the induction cooker start working. After cooking, press “ON/OFF” button to switch off the appliance. Unplug the appliance when the fan is stopped. -
“ MODE” selection
Press the “MODE” button to select the function:
Power Setting: Place the pans in the centre of stove-top. Press “ON/OFF ” button, the power indicator lights up. Then press “ MODE” button, the induction cooker start to work, the display shows “1200W”. Press and to adjust the power (Total of 8 power levels for choice).
Power | 500W | 800W | 1,000W | 1,200W | 1,400W | 1,600W | 1,800W, | 2,000W |
---|
Temperature Setting: Press the “ MODE” button, Temperature indicator lights up and the display shows “180”, that means the temperature is 180∘C. Press and to adjust the temperature ( From 60∘C-240∘C for choice).
Temperature | 60C | 8C | 10C | 120C | 14C | 16C | 180C | 20C |
---|---|---|---|---|---|---|---|---|
220C | 24C |
Timer Setting: Press the “TIMER” button when the appliance is operating, Timer indicator lights up and the display shows “0”. Press and to adjust the timer. Increase 5 min by each press. The maximum adjustable time is 180 mins.
“ LOCK/UNLOCK” setting
Press “LOCK/UNLOCK ” button to lock all settings at “ Heating” mode or “Timer”
mode. The indicator lights up. Under “LOCK” status, induction cooker would not
respond to any function except the “ON/OFF ” button. To unlock the appliance
by pressing the “ LOCK/UNLOCK ” button for 3 seconds.
SAFETY PROTECTIONS
Overheat Protection:
If the induction cooker is overheated, it will switch to “Sleeping Mode”
automatically and stop cooking by showing an “Error code” (see the below
table).
Dry-Boil Protection:
If the stove-top panel is overheat or dry boil, the induction cooker will
switch to “Sleeping Mode” automatically and stop cooking by showing an “Error
code” (see the below table).
Small Object Detection
If a Non-metallic cookware or a small metallic object (bottom diameter smaller
than 120 cm) is placed on the stove-top, the buzzer will beep continuously.
The induction cooker will stop cooking immediately. It will switch to
“Sleeping Mode” automatically if the object is not removed within 30 minutes.
Overload Protection
If the electric current or voltage is not in normal situation, the induction
cooker will change to “Sleeping Mode” automatically and stop cooking by
showing an “Error code”(see the below table).
Auto Switch-off
If a cooking utensil is removed from an operating induction cooking for 30
minutes, the appliance will stop cooking by showing an “Error Codes” (see the
below table).
TROUBLESHOOTING
Error Codes | Potential Reasons | Solution |
---|---|---|
E0 | Without cooking utensil on the stove top or using an inappropriate | |
cooking utensil. | Place or replace a suitable pan with a flatted bottomed on |
the plate.
E1| Induction cooker overheat| Clear all obstacles that block the vent
under the bottom of the induction cooker, then place the cooker in an open
area and try again after the appliance cools down.
E2| Stove-top overheat| Make sure water is inside the pan.
E3| Voltage
under-loaded/over-loaded| Make sure the voltage and frequency comply with the
rating label shown on the product.
CLEANING AND MAINTENANCE
Power must be disconnected and unplugged. Make sure the appliance had been completely cooled down before inspecting or cleaning.
-
Cleaning and Maintenance of the Stove-top
- To remove dirt, wipe with a damped cotton cloth.
- To remove the greasy stain, clean with a moist sponge soaked with mild soap, and wipe with a moist cloth, then wipe it with a dried cloth.
Notice: Never use any rough cloth or abrasive tool to clean the stove- top.
-
Cleaning and Maintenance of the vent(underneath of the appliance)
Use brush or vacuum cleaner to clear the dust on the vent, and then wipe with a dried cotton cloth.
Notice: Never apply water directly onto the air intake or exhaust vent. -
Bad contact may cause danger and harm the appliance, make sure the power plug of the induction cooker is well connected.
-
The appliance must be switched off and unplugged before regular cleaning and care.
-
Well pack the product into original packing box after regular care and cleaning. Place it at a dry and cool environment for storage.
SPECIFICATION
Model Number | PFD20 |
---|---|
Rating Voltage | AC220 – 240V, 50/60Hz |
Rating Power Output | 2000W |
Dimensions | 290 x 43 x 370 mm |
Induction cooking operating principle
The induction cooking is based on the principle of electromagnetic induction technology. Current generates variable magnetic field after running through the wire coil. Eddy current is generated at the bottom when the magnetic field induced the iron pot on the cooking plate. Large amount of thermal energy produced can heat the bottom of the utensil quickly, thus heating up the food very fast. The thermal efficiency is up to 94.36%.
Diagram
WARRANTY
- The warranty has duration of 12 months and is subject to the presentation of a copy of a suitable fiscal document or invoice proving the purchase date.
- The product is guaranteed against flaws and defects of the materials,manufacturing and assembly for 12 months from the date of the purchase invoice. The warranty consists in the replacement or repair of defective product components. It does not include the replacement of the product after breakdown repairs for any reason.
- Therefore the warranty is limited to the free replacement or repair of parts which, in the manufacturer’s opinion, malfunction. Consumable materials and tools are not included.
- Warranty services are rendered by the dealer where the product was purchased or, alternately, by the manufacturer, it being understood that the relevant transport will be at the customer’s full liability and expense.
- The warranty is invalidated if the product was tampered with or repaired by unauthorized personnel.
- This warranty substitutes and excludes any other warranty due by the dealer by law or contract and defines all the customer’s rights regarding purchased product defects and faults and/or quality deficiencies.
- Any legal controversy will be submitted to the manufacturer’s Court of residence.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>