Dometic C18B Wine storage appliance Installation Guide

: June 5, 2024
: Dometic

Table of Contents

Dometic C18B Wine storage appliance
Safety instructions
Overview
Installation
Operation
Troubleshooting
Warranty
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Dometic C18B Wine storage appliance

Explanation of symbols

WARNING!
Safety instruction: Indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION!
Safety instruction: Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
NOTICE!
Indicates a situation that, if not avoided, can result in property damage.
NOTE
Supplementary information for operating the product.

Safety instructions

!WARNING! Failure to obey these warnings could result in death or serious injury.

Electrocution hazard

Do not operate the wine cooler if it is visibly damaged.
If this wine cooler’s power cable is damaged, it must be replaced by the manufacturer, a service agent or a similarly qualified person in order to prevent safety hazards
This wine cooler may only be repaired by qualified personnel. Inadequate repairs may cause serious hazards.
When positioning the wine cooler, ensure the supply cord is not trapped or damaged.
Do not locate multiple portable socket-outlets or portable power supplies at the rear of the wine cooler.
Plug the device to sockets that ensure proper connection especially when the device needs to be earthed.

Fire hazard

The refrigerant in the refrigerant circuit is highly flammable. In the event of any damage to the refrigerant circuit:
- Switch off the wine cooler.
- Avoid naked flames and sparks.
- Air the room well.

Health hazard

This device can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the device in a safe way and understand the hazards involved
Children shall not play with the device.
Cleaning and user maintenance shall not be made by children without supervision.
Children aged from 3 to 8 years are allowed to load and unload the wine cooler.
To avoid a hazard due to instability of the wine storage appliance, it must be fixed in accordance with the installation instructions.
Keep ventilation openings, in the wine cooler enclosure or in the builtin structure, clear of obstruction.
Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
Do not damage the refrigerant circuit.
Do not open the refrigerant circuit under any circumstances.
Do not use electrical devices inside the wine cooler unless they are recommended by the manufacturer for that purpose.

Explosion hazard

Do not store any explosive substances, such as spray cans with propellants, in the wine cooler.
CAUTION! Failure to obey these cautions could result in minor or moderate injury.

Risk of crushing

Do not put your fingers into the hinge.

Health hazard

Only closed and still sealed bottles may be stored in the appliance.

Damage hazard

Check that the voltage specification on the data plate is the same as that of the power supply.
Never pull the plug out of the socket by the connection cable.
The wine cooler is not suitable for storing substances which are caustic or contain solvents.
Keep the drainage outlet clean at all times.
Never transport the wine cooler in a horizontal position, so that no oil can leak out of the compressor.
Set up the wine cooler in a dry location where it is protected against splashing water.
Operating the wine cooler safely
Failure to obey these warnings will result in death or serious injury.

Electrocution hazard

Do not touch exposed cables with your bare hands. !
Failure to obey these cautions could result in minor or moderate injury.

Electrocution hazard

Before starting the wine cooler, ensure that the power supply line and the plug are dry.

Health hazard

Opening the door for long periods can cause significant increase of the temperature in the compartments of the wine cooler.
Clean regularly surfaces that can come in contact with wine bottles and accessible drainage systems.
If the device is left empty for long periods:
- Switch off the wine cooler.
- Defrost the wine cooler.
- Clean and dry the wine cooler.
- Leave the door open to prevent mold developing within the wine cooler.
- Damage hazard
Do not place the wine cooler near naked flames or other heat sources (heaters, direct sunlight, gas ovens etc.)
Danger of overheating! Always ensure sufficient ventilation so that the heat generated during operation can dissipate. Make sure that the device is sufficiently far away from walls and other objects so that the air can circulate.
Never immerse the wine cooler in water.
Protect the wine cooler and the cable against heat and moisture.
Make sure that wine bottles do not touch the walls of the cooling area.

Scope of delivery

Wine cooler
Installation and operating manual

Intended use

The wine storage appliance (also referred to as wine cooler) is designed for operation in enclosed buildings, such as:

In staff kitchens in stores, offices and other work areas
In the agricultural sector
In hotels, motels and other accommodations
In bed and breakfast establishments
In catering businesses or similar wholesaler operations
The wine cooler is intended to be used either as a built-in appliance or as freestanding appliance. Refer to the installation instructions.
The wine cooler is intended to be used exclusively for the storage and temperature control of wine. Only closed and still sealed bottles may be stored in the appliance.
The wine cooler is not suitable for storing medicine or freezing foodstuffs.
This wine cooler is only suitable for the intended purpose and application in accordance with these instructions.
This manual provides information that is necessary for proper installation and/or operation of the wine cooler. Poor installation and/or improper operating or maintenance will result in unsatisfactory performance and a possible failure.
The manufacturer accepts no liability for any injury or damage to the product resulting from:
Incorrect assembly or connection, including excess voltage
Incorrect maintenance or use of spare parts other than original spare parts provided by the manufacturer
Alterations to the product without express permission from the manufacturer
Use for purposes other than those described in this manual
Dometic reserves the right to change product appearance and product specifications.

Technical description

The models of the wine cooler are equipped with:

Two temperature zones:
- C18B, C46B, D18B, D46B: upper zone: 4 °C to 12 °C
- C18B, C46B, D18B, D46B: lower zone: 12 °C to 22 °C
- D42B: left and right zone: 4 °C to 22 °C
Automatic defrost function
Sensor buttons
°C/°F temperature display
Interior LED lamp
Temperature memory function: The set temperature is saved when the wine cooler is switched off.
Temperature monitor: A warning signal sounds and the temperature display flashes if the interior temperature noticeably deviates from the one set.

Overview

Dometic C18B Wine storage appliance 26

Control elements

Dometic C18B Wine storage appliance 27

Dometic C18B Wine storage appliance 28 Dometic
C18B Wine storage appliance 2

Installation

Selecting the installation location

Observe the following, when selecting the installation location:

The ambient temperature should be in accordance with the climate class. Otherwise, it is possible that the inner temperature you set cannot be reached or maintained. This could also be the case if there are extreme fluctuations in the ambient temperature.
The intended ambient temperature use and the climate class can be found in the technical data (see chapter “Technical data” on page 31) and on the data plate, which is located at the left on the inside of the wine cooler.
The ground must be level and sufficiently stable to support the wine cooler at full capacity.
The wine cooler must be positioned so that the plug is accessible.
Note the information on the electrical connection, see chapter “Connecting the wine cooler” on page 23.
Remove all the inner and outer packaging material before setting up.

Integrating free-standing wine coolers

The wine cooler can be integrated either under a countertop or between other cabinets
Observe the following, when integrating the wine cooler
Observe the installation dimensions
Ensure the door will open and close properly in the chosen location.
Waste heat produced by the wine cooler must be extracted via ventilation openings on the rear and at both sides.

Mounting the door handle
Mount the handle Dometic C18B Wine storage appliance
5

Adjusting the feet
Make sure the wine cooler is level by adjusting the feet Dometic C18B Wine
storage appliance 7 Adjusting the ventilation grille
Adjust the height of the ventilation grille Dometic C18B Wine storage
appliance 8 Changing the door hinge

* You can change the hinge of the door, so that it opens to the left rather than the right.

Proceed as shown to change the door hinge
Reverse the door handle

Connecting the wine cooler

Observe the following when connecting the wine cooler:
Leave the wine cooler to stand upright for about 2 hours after transporting, before you connect it to the power supply. Otherwise this could cause faults in the cooling system.
Connect the wine cooler to a circuit that is protected with 15 A.
Have the socket and power circuit checked by a qualified electrician to ensure that the socket is earthed correctly. Do not use an extension cable or a multiple power socket.
The power cable must rest securely behind the wine cooler and not be allowed to lie or hang unprotected.
Ensure that the power cable is not jammed when pushing the wine cooler into place.
Connect the plug of the connection cable into the AC mains.
The display turns on.

Operation

Before first use
Before first use, clean the wine cooler inside and outside with a damp cloth for hygienic reasons (see also chapter “Cleaning and maintenance” on page 29).

Storing bottles

Please note the following:

Only store wine in wine bottles that are closed and still sealed.
Do not overload the wine cooler.
Do not cover the shelves with aluminum foil or any other objects, as this obstructs the air circulation.
After a power cut or if the wine cooler has been switched off, wait 3 to 5 minutes before switching on the wine cooler again.
Position the bottles

Saving energy

Only open the wine cooler as often and for as long as necessary.
Avoid unnecessarily low temperature settings.
For optimal energy consumption, position the shelves and drawers according to their position on delivery.
On a regularly basis, make sure the door seal still fits properly.
Clean dust and dirt from the condenser at regular intervals.

Switching on and off

To switch on and off, press the button for at least 6 seconds.

Setting the temperature

To avoid food waste, note the following:

Keep temperature fluctuation as low as possible. Only open the wine cooler as often and for as long as necessary. Store the wine bottles in such a way that the air can still circulate well.
Adjust the temperature to the quantity and type of the wine bottles

Setting the unit (°C or °F)

You can select whether the temperature is displayed in Fahrenheit or Celsius.
Press the buttons simultaneously for 2 seconds.
✔ The unit is converted and the display shows the temperature in the selected unit.
Increasing and decreasing the temperature
The temperature can be set separately for the two zone.
Press the corresponding button to set the temperature.
✔ The display flashes while you adjust the setting.
✔ Once you have set the temperature, the display shows the current temperature

Checking the set temperature

Press the button briefly.
✔ The set temperature is shown in the display for 5 seconds.
Then the display shows the current inner temperature again

Monitoring the temperature

The warning signals prevent the temperature from falling or rising too much unnoticed, which could affect the quality of the wine. Once the wine cooler has reached the set temperature, the warning signal and the temperature display flashing stops.
A warning signal sounds and the temperature display flashes in the following cases:
The inner temperature deviates from the set temperature by more than 5 °C. To switch off the warning signal prematurely:
Press the button briefly.
✔ The temperature display flashes until the set temperature is reached. The display is then illuminated constantly and indicates that the alarm system is active again.

Storing and serving temperatures for wine

The recommended storing temperature for white wine and red wine is between 10 °C and 14 °C.
The serving temperature depends on the origin and grape.

Region

| Serving temperature

White wine Red wine

---|---
Bordeaux| 12 °C| 18 °C
Bourgogne| 10 °C| 16 °C
Loire| 10 °C| 15 °C
Languedoc| 12 °C| 18 °C
Alsace grands crus| 12 °C| 16 °C
Piedmont, Tuscany| 10 °C| 18 °C
Rioja| 12 °C| 18 °C
Napa Valley| 12 °C| 16 °C
Australia| 10 °C| 16 °C
Chile| 10 °C| 18 °C
Liqueur wine| 8 °C| –
Champagne| 6 °C| –

Switching on and off the interior LED lamp
To switch on and off, press the button for at least 5 seconds.

Unlocking the keys

To unlock the keys, press the and buttons simultaneously for at least 5 seconds.
If there is no operation during 120 seconds, the keys are locked automatically

Moving the cabinet shelves

The shelves can be pulled out by a third so that you can reach the wine bottles easily.
The shelves have a limit stop to prevent them from being pulled out too far.
Proceed as shown to remove one of the shelves from the guide rail

Defrosting

The wine cooler is equipped with an automatic defrost function.

Switching off and storing the wine cooler

If you do not intend to use the wine cooler for a long time, proceed as follows:
Press the button until the wine cooler switches off.
Disconnect the power cable.
Clean the wine cooler (see chapter “Cleaning and maintenance” on page 29).
✔ The door stays open thus preventing smells from arising

Troubleshooting

Fault	Possible cause	Remedy
The wine cooler is not	The temperature is not set prop-	Check the set

Cleaning and maintenance

Clean the wine cooler regularly and as soon as it becomes dirty with a dampcloth.
Ensure that no water drips into the seals. This can damage the electronics.
Wipe the wine cooler dry with a cloth after cleaning.
Check the condensate drain regularly.
Clean the condensate drain when necessary. If it is blocked, the condensate collects on the bottom of the wine cooler

Replacing the active charcoal filter

Replace the active charcoal filer with a new one once a year Dometic C18B
Wine storage appliance 22

Turn the filter by 90° clockwise or anti-clockwise and remove it.
Insert a new filter.
Turn the filter 90° clockwise or anti-clockwise until it clicks into position.

Warranty

The statutory warranty period applies. If the product is defective, please contact your retailer or the manufacturer’s branch in your country (see dometic.com/dealer).
For repair and warranty processing, please include the following documents when you send in the product:
A copy of the receipt with purchasing date
A reason for the claim or description of the fault
Note that self-repair or nonprofessional repair can have safety consequences and might void the warranty.

Disposal

If the product contains any non-replaceable batteries, rechargeable batteries or light sources, you don’t have to remove them before disposal.
If you wish to finally dispose of the product, ask your local recycling center or specialist dealer for details about how to do this in accordance with the applicable disposal regulations.
The product can be disposed free of charge.
Place the packaging material in the appropriate recycling waste bins wherever possible.

Technical data
For the current EU declaration of conformity for your device please refer to the respective product page on dometic.com or contact the manufacturer directly (see dometic.com/dealer). Further product information can be accessed via QR code on the energy label in the figures or via eprel.ec.europa.eu

	C18B	C46B
Input voltage:	220 – 240 Vw

50 Hz

– upper zone:

– lower zone:

|

4 °C to 12 °C

12 °C to 22 °C

Intended ambient tempera- ture use:| +10 °C to +32 °C
Noise emission:| 39 dB(A)
| C18B| C46B
---|---|---
Propellant:| Cyclopentane
Refrigerant:| R600a
Dimensions (W x H x D):| see fig. m, page 14| see fig. n, page 14
Weight:| 30 kg| 42 kg
Test/certificates:|