StrikeMaster LFV-CB Lithium 40v Battery Charging Base Owner’s Manual

LITHIUM 40V
LITHIUM-ION BATTERY CHARGER

OWNER’S MANUAL
TOLL-FREE HELPLINE: 1-877-572-7278
(Monday – Friday / 8am – 4:30pm CST)

READ ALL SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATING

PRODUCT SPECIFICATIONS

COMPONENTS

• StrikeMaster 40v Lithium Battery Charging Base is compatible with the
  Lithium 40v 5 amp(LFV-B) and 6 amp(LFV6-B) Lithium Ion Batteries.

• Input: 120V AC 50/60Hz 1.5A

• Output: 40V DC 2.2A

• Weight: 1.48 lbs., (0.67 kg)

STRIKEMASTER® LITHIUM 40v BATTERY CHARGING BASE QUICK START

1. Remove Lithium 40v Battery Charging Base from the carton (Image 1). Plugin.

2. Unpack Battery, and slide the Battery onto Battery Charging Base using the channels on both sides as a guide. Press down until you hear it click in place. Leave Battery on Battery Charging Base until fully charged.
   NOTE : Battery is not fully charged when first removed from the box and will not charge until The battery’s core temperature is above 32°F

3. When the Battery Charging Base indicator shows green, your battery is charged (Image 3).

Your StrikeMaster Lithium 40v Battery is ready for use.
Your StrikeMaster Lithium 40v Battery Charging Base has built-in “Smart Charging
Technology”. The chart below shows you the correct charging procedure/occurrences that could be experienced while charging.

REGISTER YOUR PRODUCT ONLINE TO ACTIVATE YOUR WARRANTY
www.rapala.com/content/rapala-brand-warranties/strikemaster- warranty.html

SAFETY INFORMATION

IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS DANGER – TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS
Read and understand all instructions before using this product. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury.

WARNING
FOR INDOOR USE ONLY

CAUTION
RISK OF ELECTRIC SHOCK. DRY LOCATION USE ONLY.
Store Indoors and do not expose to rain or water. Avoid direct sunshine.

CAUTION
RISK OF FIRE OR ELECTRIC SHOCK, DO NOT INTERCONNECT OUTPUT TERMINATIONS
CAUTION
CHARGE ONLY RECHARGEABLE LI-ION BATTERY PACK LFV-B/LFV-BEU, OTHER TYPES OF BATTERIES MAY BURST CAUSING PERSONAL INJURY AND DAMAGE
DANGER

RISK OF ELECTRIC SHOCK. DO NOT TOUCH THE UNINSULATED PORTION OF THE OUTPUT CONNECTOR OR UNINSULATED BATTERY TERMINAL

SAVE THESE INSTRUCTIONS

• This manual contains important safety and operating instructions for Battery Charging Base LFV-CB.

• Before using the Battery Charging base, read all instructions and cautionary markings on Battery Charging Base, Battery, and StrikeMaster Lithium 40v Ice Auger.

• To reduce the risk of fire and electric shock, install in a temperature- and a humidity-controlled indoor area relatively free of conductive contaminants.

• Use of an attachment not recommended or sold by the Battery Charging Base manufacturer may result in a risk of fire, electric shock, or injury to persons.

• Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

• Do not abuse the cord or Charging Base. Never use the cord to carry the Charging Base. Do not pull the charger cord rather than the plug when disconnecting from the electrical outlet. Damage to the cord or charger could occur and create an electric shock hazard. Bring to an authorized service center if cords are damaged.

• Do not operate the charger if it has received a sharp blow, been dropped, or otherwise damaged in any way. Take it to an authorized service center for the electrical check to determine if the charger is in good working order.

• Do not cover the ventilation slots on the top of the charger. Do not set the charger on a soft surface i.e. blanket, or pillow. Keep the ventilation slots of the charger clear.

• Do not probe the charger with conductive materials.

• Do not disassemble the Charging Base. Take it to an authorized service center when service or repair is required.
  Incorrect reassembly may result in a risk of electric shock or fire.

• Disconnect Charging Base from the power supply when not in use. This will reduce the risk of electric shock or damage to the charger if metal items should fall into the opening. It also will help prevent damage to the Charging Base during a power surge.

• Do not use a damp cloth or detergent to clean the Battery or Charging Base. Clean / wipe down with a dry cloth.

• Do not allow the battery pack or charger to overheat. If they are warm, allow them to cool down. Recharge only at room temperature.

• Unplug the Charging Base before cleaning and when there is no battery in the charger.

• Do not try to connect two chargers together.

• Do not allow the liquid inside the Charging Base.

• Do not try to use the charger for any other purpose than what is presented in this manual.

• Save these instructions. Refer to them frequently and use them to instruct others who may use this Auger. If you loan someone this Auger, loan them these instructions also to prevent misuse of the product and possible injury.

• Confirm the voltage in each country before using the Charging Base.

• If the shape of the plug does not fit the power outlet, use an attachment plug adaptor of the proper configuration for the power outlet.

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

avoided, will result in death or serious injury.
| WARNING| Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
| CAUTION| Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
| CAUTION| (Without Safety Alert Symbol) Indicates a situation that may result in property damage.

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.

and understand owner’s

KNOW YOUR CHARGING BASE

The safe use of this product requires an understanding of the information on the product and in this owner’s manual as well as a knowledge of the project you are attempting.  Before using this product, familiarize yourself with all operating features and safety rules.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.

WARNING
Changes or modifications to this unit not expressly approved by the manufacturer for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to  radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARNING
Do not allow familiarity with products to make you careless. Remember a careless fraction of a second is sufficient to inflict serious injury.
WARNING
Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury.
CAUTION
Charge in a well-ventilated area. Do not block charger vents. Keep them clear to allow proper ventilation.

OPERATION

CHARGING PROCEDURE
NOTE: The Battery Pack is not shipped fully charged. It is recommended to fully charge before first use to ensure that maximum run time can be achieved. This lithium-ion battery will not develop a memory and may be charged at any time.
LOW VOLTAGE CHARGING
If the battery has been stored with little to no charge for a long period of time, the charger will go into recovery mode, which will take 20 hrs. to fully charge the battery. This will enhance the life of the battery. Once it is fully charged, the next charge will return to standard charging.
A fully discharged battery pack will require approximately 150 minutes for 5ah and 180 minutes for 6ah to fully charge from a discharged state.
1. Plug the Charging Base into an AC power outlet.
2. Insert the Battery into the Charging Base.
This is a diagnostic charger. The Charging Base LED Lights will illuminate in a specific order to communicate the current battery status. They are as follows:

FALSE DEFECT NOTE
When the Battery is inserted into the Charging Base and the status LED blinks RED, remove the Battery from the charger for 1 minute, then reinsert it. If the status LED  blinks GREEN, then the Battery is properly charging. If the status LED is still blinking RED, remove the Battery and unplug the Charging Base for 1 minute. After 1 minute, plug in the Charging Base and reinsert the Battery. If the status LED blinks GREEN, then the Battery is properly charging. If the status LED is still blinking RED, the Battery is defective and needs to be replaced.
NOTE: When the red indicator flickers, pull out the Battery from the Charging Base and insert it again within 2 hours.
If the indicator shows charging, that means the Battery is good. After 2 hours, please pull out the Battery and also pull out the AC power plug of the Charging Base for 1  minute, and then insert the AC power plug and the Battery again. If the indicator shows charging, that means the Battery is good. If not, the Battery needs to be replaced.

CHARGING BASE MOUNTING

1. This Charging Base can be installed hanging on a wall using two screws (not included)
2. Locate the placement for the Charging Base to be wall-mounted.
3. If fastening to wood studs use 2 wood screws.
4. Drill two holes 2-3/8” (6 cm) in the center ensuring they are level.
5. If fastening to drywall use wall anchors and screws to secure the Charging Base to the wall.
6. This power unit is intended to be correctly orientated in a vertical or floor mount position.

NOTE: If the Battery and the Charging Base won’t be used for a long time, remove the Battery from the Charging Base and unplug the AC power plug.

MAINTENANCE

WARNING
To avoid serious personal injury, always remove the Battery from the Auger when cleaning or performing any maintenance.
WARNING
When servicing, use only identical StrikeMaster replacement parts. The use of any other parts may create a hazard or cause product damage
WARNING
It is not recommended to use compressed air as a cleaning method for this charger. If cleaning with compressed air is the only method to apply, always wear safety goggles or safety glasses with side shields when using compressed air to clean the tool. If the operation is dusty, also wear a dust mask.
GENERAL MAINTENANCE

• Brush or blow dust and debris out of the air vents using compressed air or a vacuum. Keep the air vents free of obstructions, sawdust, and wood chips. Do not spray, wash, or immerse the air vents in water.
• Wipe off the housing and the plastic components using a dry, soft cloth. Do not use strong solvents or detergents on the plastic housing or plastic components. Certain household cleaners may cause damage and may cause a shock hazard.

STORAGE

• Always remove the Battery Pack before storing the Charging Base or any time the Charging Base is unplugged.
•  Do not place the Battery Pack in the sun or in an extremely warm environment. Keep at normal room temperature.
• If the battery will not be used for 3 months or more, store the Battery in a controlled temperature environment. Fully charge before storage.

WARNING
Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc. come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.

TROUBLESHOOTING

Charger doesn’t work. Charger
shows defective mode (LED flashes Red)| Battery or Charging Base
is defective or bad connection
between Battery and Charging Base| 1) Try to remove and reinsert the Battery in the Charging Base
2) Try charging a different battery
3) Unplug the Charging Base and wait until the red LED goes out. Then reconnect the plug to the power supply
Charging Base doesn’t work.
Charging Base shows evaluation
mode (LED indicates Red solid ON)| The battery is too hot or too cold| Allow the Battery to reach normal temperature.
Charging will begin when the Battery returns to 37°F-117°F (3°C -47°C)

2-YEAR LIMITED WARRANTY

CHARGING BASE WARRANTY

StrikeMaster® hereby warranties this product, to the original purchaser with proof of purchase, for a period of two (2) years against defects in materials, parts, or workmanship. Batteries must be charged in accordance with the owner’s manuals directions and regulations in order to be valid. StrikeMaster, at its own discretion, will repair or replace any and all parts found to be defective, through normal use, free of charge to the customer. This warranty is valid only for units that have been used for personal use that have not been hired or rented for industrial/ commercial use, and that have been maintained in accordance with the instructions in the owner’s manual supplied with the product from the new.

ITEMS NOT COVERED BY WARRANTY

1.  Any part that has become inoperative due to misuse, commercial use, abuse, neglect, accident, improper maintenance, or alteration; or
2.  The unit, if it has not been operated and/or maintained in accordance with the owner’s manual; or
3. Normal wear, routine maintenance, normal deterioration of finish due to use or exposure.

REGISTER YOUR PRODUCT ONLINE TO ACTIVATE YOUR WARRANTY
www.rapala.com/content/rapala-brand-warranties/strikemaster- warranty.html

TRANSPORTATION CHARGES
Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. It is the purchaser’s responsibility to pay transportation charges for any part submitted for replacement under this warranty unless such return is requested in writing by StrikeMaster.

10395 Yellow Circle Drive • Minnetonka, MN 55343

TOLL-FREE HELPLINE: 1-877-572-7278
(Monday – Friday / 8am – 4:30pm CST)
www.strikemaster.com

References

• brand-warranties-rapala-warranty-us - Rapala
• Official StrikeMaster® Augers Canada Site | Electric & Hand Augers
• Official StrikeMaster® Augers Site | Ice Fishing Auger Drills

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>