PANDUIT 1005512 Stainless Steel Quad Cable Cleat Instruction Manual

PANDUIT 1005512 Stainless Steel Quad Cable Cleat

TO REDUCE THE RISK OF INJURY, USER MUST READ INSTALLATION INSTRUCTIONS BEFORE ATTEMPTING TO INSTALL

NOTE: In the interest of higher quality and value, Panduit products are continually being improved and updated. Consequently, pictures may vary from the enclosed product.
NOTE: Updates to this Installation Instructions may be available. Check www.panduit.com for the latest version of this manual.

Preparing for Order

selection.
2| | Measure actual diameter of the cables. Select a cleat part number based on the actual diameter of the cables.
3| | If using a mounting bracket to secure cleat, measure height of the ladder rung and reference chart below. If using a bolt to secure cleat, procure M8 or 5/16” bolts, washers, and nuts with sufficient length to pass through the ladder rung.
Rung Height| Mounting Bracket Part Number
---|---
15mm (.59”) or less| CBH15L50- V6
15mm (.59”) to 20mm (.79”)| CBH20L50- V6
20mm (.79”) to 25mm (1.01”)| CBH25L50- V6
25mm (1.01”) to 30mm (1.16”)| CBH30L50- V6

**Cable Cleat Nomenclature

**

• Start on Page 3 if installing by Mounting Bracket.
• Start on Page 6 if installing with Mounting Fasteners.

Mounting Method 1: Mounting Bracket

| Measure the cable diameter. Refer to the chart on page 8. In some instances, the top spacer will need to be removed before installation.
2| | Insert mounting bracket into slot in bottom plastic spacer of cable cleat.
3| | Slide cleat and mounting bracket over rung in the desired position on the rung.
4| | Rotate swing bolt until the carriage head rests within the matching opening in the top of the mounting bracket. Tighten flange nut to 60 in- lbs [6.8Nm].
---|---|---
5| ****

| Open top clamshell and place quad cables in the opening in a quad configuration. Close top clamshell around the cables.
6| ****| Assemble included nut and washer onto the securing bolt. Tighten to 15 ft-lbs [20.3Nm].

In some cases, the flanges of the shells will come together before the torque is met. In other cases, there will be a gap between the flanges after the torque is met.

Mounting Method 2: Mounting Fasteners

| Position cleat over the appropriate hole or slot in the rung. Assemble securing bolt through the hole in the bottom of the cleat.

A carriage bolt is shown however in some circumstances a hex bolt might be used.

Locking nuts and/or washers are recommended if fasteners could become loose over time.

3| | Tighten securing bolt to 120 in-lbs [13.6Nm].
4|

| Measure the cable diameter. Refer to the chart on page 8. In some instances, the top spacer will need to be re- installed before installation.
---|---|---
5| ****| Open top clamshell and place cables in the opening in a quad configuration.

Close top clamshell around the cables.

6| | Assemble included nut and washer onto the securing bolt. Tighten to 15 ft-lbs [20.3Nm].

In some cases, the flanges of the shells will come together before the torque is met. In other cases, there will be a gap between the flanges after the torque is met.

Spacer Decision Table

Part Number

| Cable Range| With Top Spacer| Without Top Spacer
---|---|---|---
CCSSQD2226-X| 22 – 26mm| 22 – 24mm| 24 – 26mm
CCSSQD2529-X| 25 – 29mm| 25 – 27mm| 27 – 29mm
CCSSQD2834-X| 28 – 34mm| 28 – 31mm| 31 – 34mm
CCSSQD3339-X| 33 – 39mm| 33 – 36mm| 36 – 39mm
CCSSQD3844-X| 38 – 44mm| 38 – 41mm| 41 – 44mm

Email:
techsupport@panduit.com
EU Website:
www.panduit.com/emea
EU Email:
emeatoolservicecenter
@panduit.com 

Panduit Corp.
USA Technical Support
Tel: 800-777-3300
Panduit Europe • EMEA Service Center
Tel: +31 546 580 452 • Fax: +31 546 580 441

References

• Panduit | Network Infrastructure and Industrial Electrical Wiring

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>