asa MSBAR Soundbar Integrated LED Light Strip Owner’s Manual
- June 5, 2024
- ASA
Table of Contents
MSBAR
Quick Reference Guide
Marine Waterproof
Bluetooth/Aux Soundbar
with Integrated LED Light
Strip
WARNING:
The MSBAR weighs 14lbs (6.35 Kg). Before mounting this soundbar, ensure the intended mounting surface is designed to properly support this amount of weight.
FCC COMPLIANCE STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC warning:
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body
WARNING: Cancer and Reproductive Harm
–www.P65Warnings.ca.gov
Features:
Marine Waterproof Bluetooth/Aux Soundbar with Integrated LED Light Strip
Bluetooth:
Version: 5.0
Range: 33ft(10m) Class 2
Speakers:
Cone Type: polypropylene
Amplifier:
Rated Power (RMS): 120W
Rated Power (Peak): 180W
Frequency Response: 75Hz~13KHz.
General:
Operational Power: 12VDC(Max Current Draw: 12A,Fuse:15A )
Cabinet Material: Aluminum Extrusion
Color: Black Powder Coating
Weight: 14lbs/6.35kg
Dimensions: 780x202x137.5(mm) / 30.7”x7.95”x5.41”(inch)
SAFETY INFORMATION
- To ensure full satisfaction with the product, please read the entire instruction manual.
- Keep instructions for future reference.
- Follow all operation guidelines and adhere to all safety warnings and cautions to ensure safe use.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Only use attachments/accessories specified by the manufacturer.
- Never use harsh cleaning agents. Clean only with mild cleaner and soft cloth.
When Driving
Keep the volume level low enough to be aware of your surroundings.
Protect from Water
Do not submerge, as this can cause electrical shorts, fire or other damage.
Avoid power washing amplifier as water pressure may exceed IPX5 water rating.
Protect from High Temperatures
Exposure to direct sunlight for an extended period of time can produce very
high temperatures inside your vehicle. Give the interior a chance to cool down
before starting playback. Do not mount the radio within close proximity of the
engine compartment.
Use the Proper Power Supply
This product is designed to operate with a 12 volt DC negative ground battery
system.
WARNING:
- DO NOT OPEN, DISASSEMBLE OR ALTER THE UNIT IN ANY WAY. Doing so may result in fire, electric shock or product damage.
- USE THE CORRECT AMPERE RATING WHEN REPLACING FUSE. Failure to do so may result in fire, electric shock or product damage.
- DO NOT INSTALL IN LOCATIONS THAT MIGHT HINDER VEHICLE OPERATION. Doing so may obstruct vision or hamper movement which can result in a serious accident.
- INSTALL THE WIRING SO THAT IT IS NOT CRIMPED OR PINCHED BY SCREWS OR SHARP METAL EDGES. Route the cables away from moving parts or sharp pointed edges. This will prevent crimping and damage to the wiring. If the wiring must pass through a metal hole, be sure to use a rubber grommet to prevent the wire’s insulation from being cut by the metal edge of the hole. It is also recommended to apply sealing caulk to any opening that may potentially allow water to enter.
- Be sure to choose a location that is flat and has clearance above the unit to prevent any damage, as well as allow for ventilation. Please orient and mount horizontally or vertically if possible.
- Before drilling any holes, carefully inspect the area underneath and behind the mounting surface where the device will be mounted to make sure it will not interfere with existing wires, fuel lines, the fuel tank or any other objects that could be damaged.
- Always disconnect the vehicle negative battery terminal during installation to prevent accidental shorting.
MOUNTING THE SOUNDBAR
With N-Bracket
Install rubber bushings on
square bar
Install n-barckets on rubber bushings
Install rubber bushings on side-barckets
Align the bolts and nuts ,firmly tighten
Without N-Bracket
screwing or bolt directly into the mounting surface.
The side-bracket can be installed in the enclosure to adjust the left and
right angles, and can also adjust the height up and down. The adjustment
method is shown in the picture, loosen the screw, adjust to your desired angle
or height, and re-tighten the screw.
When the bracket is completely vertical, attach one bolt at the center hole
and one in either of the side holes. In all other cases, there will only be
two holes that align with the bracket slot, secure a bolt at each point.
WIRE DIAGRAM
A 3.5mm AUX OUT
— AUX output can be connected to the AUX input of a second MSBAR, subwoofer
amplifier, or more to expand your sound system. Signal level is 2 Volts.
Note: The ‘REMOTE’ wire can either be connected to +12VDC switched source or amplifier remote turn on from source head unit. When using a headunit, connecting to the remote turn on is recommended to prevent popping noise when turning on audio system.
Operation
A Switch – Power&Bluetooth Pairing
(Blue LED ring color)
B Switch – Led light bar on/off
(Blue LED ring color)
POWER/BLUETOOTH
- Press Power/Bluetooth switch to turn the device on and off (standby). Press and hold the Power/Bluetooth Switch for about 3 seconds to enter the Bluetooth pairing mode (Bluetooth name: MSBAR) The speaker should remain in Bluetooth pairing mode for 120 seconds. If there is no paired device, it will return to normal operation. The last paired device should be remembered. Bluetooth pairing is only needed when the user wants to pair to different devices. When power is on, The MSBAR will automatically connect to the last paired device.
- When the Bluetooth device is connected or in AUX mode, the LED is always on. LED is always off when the power is off (standby) When in Bluetooth mode and no Bluetooth device is connected, the LED will flash slowly
- When the AUX line detects a 3.5mm input, it should automatically switch to AUX mode and be fixed in AUX mode. When AUX does not detect AUX input, it will automatically switch back to Bluetooth mode and be fixed in Bluetooth mode. Note: Mode switching is only controlled by AUX input detection, without manual control.
LED LIGHT BAR SWITCH:
- Press LED light bar switch to turn the LED light bar on and off.
- When the MSBAR is powered, the LED on/off switch will be illuminated with a blue light ring. This allows the switch to be easily located at night.
ASA ELECTRONICS,LLC
2602 MARINA DRIVE ELKHART IN 46514
U.S.A.
MADE IN CHINA
Documents / Resources
| asa
MSBAR Soundbar Integrated LED Light
Strip
[pdf] Owner's Manual
MSBAR Soundbar Integrated LED Light Strip, Soundbar Integrated LED Light
Strip, LED Light Strip
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>