JENNAIR B0030IY1MW Bottom Mount Refrigerator User Guide

JENNAIR B0030IY1MW Bottom Mount Refrigerator ELECTRICAL REQUIREMENTS

WARNING
Electrical Shock Hazard

• Plug into a grounded 3 prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Failure to follow these instructions can result in death, fire, or electrical shock.

A 115 V, 60 Hz, AC only, 15 A or 20 A fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord. NOTE: Before performing any type of installation, cleaning, or removing a light bulb, turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting. See “Using the Controls.”

LOCATION REQUIREMENTS

WARNING
Explosion Hazard

• Keep flammable materials and vapors, such as gasoline, away from the refrigerator.
• Failure to do so can result in death, explosion, or fire.

Floor must support the refrigerator weight, more than 600 lbs
(272 kg), door panels, and contents of the refrigerator.
Each refrigerator needs to be installed in a separate cabinet frame.

NOTE: This refrigerator is intended for use in a location where the temperature ranges from a minimum of 13°C (55°F) to a maximum of 43°C (110°F). The preferred room temperature range for optimum performance, which reduces electricity usage and provides superior cooling, is between 15°C (60°F) and 32°C
(90°F). It is recommended that you do not install the refrigerator near a heat source, such as an oven or radiator.

OPENING DIMENSIONS

This refrigerator is designed to be installed inside a frame that ts between kitchen cabinets. The inside of the frame should be a minimum of 6915/16″ (1776 mm) high, 221/16″ (560 mm) wide, and 217/8″ (555 mm) deep (front to back).
For proper ventilation, you must allow adequate unobstructed space behind the refrigerator and below and above the frame. Air enters below the refrigerator and exits above it.
Allow a clearance minimum of 2″ (50 mm) at the top of the frame. The minimum depth of the base of the frame is 207/16″ (520 mm) (front to back).
The base can be as desired, but height should match height of toe kick of surrounding cabinets. A vent with an opening of at least 31 sq in. (200 sq. cm) is required for proper ventilation.
If the space between the top of the frame and the ceiling is open air, allow a minimum of 77/8″ (200 mm) above the refrigerator.
If the space between the top of the frame and the ceiling is enclosed as part of the surrounding cabinetry, a vent with an opening of at least 31 sq. in. (200 sq. cm) is required.
The bottom of the vent must be a minimum of 77/8″ (200 mm) above the refrigerator.
NOTE: Vent covers are not supplied with the unit.

Dimension Table

A| 69 15/ 16 ” (1776 mm)
B| 22 1/ 16 ” (560 mm)
C| Minimum 21 7/ 8 ” (555 mm)
D| Minimum 20 7/ 16 ” (520 mm)
E| Minimum 2″ (50 mm)
F| 69 11/ 16 ” (1770 mm)
G| 21 15 / 16” (557 mm)
H| 21 7/ 16 ” (545 mm)
I| 2 15/ 16 ” (75 mm)
J| 1 3/ 32 ” (28 mm)
K| 40 11/ 32 ” (1024.5 mm)

Dimensions are for planning purposes only. For complete details, see Owner’s Manual packed with product. Specifications subject to change without notice.

PRODUCT DIMENSIONS

The unit is 6911/16″ (1770 mm) high, 2115/16″ (557 mm) wide, and 217/16″ (545 mm) deep (front-to-back).
The refrigerator door (including hinges [x2]) is 4011/32″ (1024.5 mm) high. The freezer door (including hinges [x2]) is 27″ (685.5 mm) high.
The space between the refrigerator and freezer doors is 215/16″ (75 mm). The space between the door hinges is 25/32″ (20 mm).
A grounded 3 prong electrical outlet should be placed within 4″ (101 mm) of the right side cabinets or end panel. See
“Electrical Requirements” for additional information.

Door Panels Requirements (each door)

Max Weight: 26.5 lbs (12 Kg)

Minimum Panels Dimensions:
Refrigerator Door Panel: 421⁄8″ (1071.5 mm) x 23¼” (590 mm) x 3/4″ (20 mm)
Freezer Door Panel: 275⁄8″ (701.5 mm) x 23¼” (590 mm) x 3/4″ (20 mm).
For maximum dimensions, please review the following diagram.

Cabinet frame wall thickness 16 mm

min. R1 [mm]| B [mm]
594| 593| 592| 591| 590

A

[mm]| 16| 0| 0| 0| 0| 0
17| 0| 0| 0| 0| 0
18| 0| 0| 0| 0| 0
19| 0| 0| 0| 0| 0
20| 0| 0| 0| 0| 0
21| 0.4| 0| 0| 0| 0
22| 2.6| 2| 1.3| 0.7| 0
23| 5| 4.4| 3.8| 3.2| 2.6
24| 7.5| 7| 6.5| 6| 5.5

How to read this diagram:
For example if the door panel width dimension “B” is 593 mm and thickness of door panel dimension “A” is 22 mm that means that door panel require radius “R1” min 2 mm.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>