SEALEY RD2500.V6 2500W 7 Element Oil Filled Radiators Instruction Manual
- June 5, 2024
- SEALEY
Table of Contents
SEALEY RD2500.V6 2500W 7 Element Oil Filled Radiators
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY
ELECTRICAL SAFETY
WARNING! It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe
before using. Inspect power supply leads, plugs and all electrical connections
for wear and damage. Sealey recommend that an RCD (Residual Current Device) is
used with all electrical products. You may obtain an RCD by contacting your
local Sealey stockist.
If the heater is used in the course of business duties, it must be maintained
in a safe condition and routinely PAT (Portable Appliance Test) tested.
ELECTRICAL SAFETY INFORMATION It is important that the following information is read and understood.
Ensure that the insulation on all cables and on the appliance is safe before
connecting it to the power supply.
Regularly inspect power supply cables and plugs for wear or damage and check
all connections to ensure that they are secure. IMPORTANT: Ensure that the
voltage rating on the appliance suits the power supply to be used and tha the
plug is fitted with the correct fuse – see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
DO NOT pull the plug from the socket by the cable
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty
item is repaired or replaced immediately by a qualified electrician.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply off
and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact
a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
Ensure that the cable outer sheath extends inside the cable restraint and that
the restraint is tight. Sealey recommend that repairs are carried out by a
qualified electrician.
GENERAL SAFETY
WARNING! Disconnect the heater from the mains power, before servicing or
performing any maintenance, which must only be carried out by an authorised
service agent. Report any oil leakage immediately to an authorised service
agent.
Replace or repair damaged parts. Use recommended parts only. Unauthorised
parts may be dangerous and will invalidate the warranty.
Ensure that the heater is used in an area larger than 4m³. Allow a few
centimetres of clearance from any surface, and ensure there is good overhead
clearance for heat circulation.
Only use the heater in an upright position.
WARNING! DO NOT tamper with the wiring, heating element or oil. The system is a sealed unit. The breaking of any seal may be dangerous, will damage the heater and will invalidate the warranty.
DO NOT use the heater for anything other than its intended purpose. It is
designed for providing heat in enclosed areas, no smaller than 4m³, such as
offices, homes, workshops etc. It is not suitable for drying clothes or
laundry.
DO NOT place the heater close to a bath, wash basin, shower, swimming pool or
any other water-filled area or wet surface. DO NOT get the heater wet or use
in areas of high condensation.
DO NOT place the heater up against any surface such as a wall, door, furniture
etc.
DO NOT place the heater immediately below any electrical outlet.
DO NOT allow the power lead to touch the radiator surface.
DO NOT cover the radiator or use it to dry laundry.
DO NOT switch the heater on whilst the electrical lead is wrapped on the
storage bracket.
DO NOT store the electrical lead until the radiator is cold.
DO NOT attempt to repair a damaged heater, contact an authorised service
agent.
DO NOT stand on the heater.
DO NOT touch the heating elements when the heater is on as it becomes very
hot.
Operators must read this manual or receive adequate training before using the
heater.
Children should be supervised at all times when the heater is in use.
Ensure that the heater is correctly turned off when not in use and store in a
safe, dry area, out of reach of children.
NOTE: This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
INTRODUCTION
Oil-filled radiator suitable for office, home, showroom and workshop use. Manufactured to rigorous safety standards and fitted with a 13Amp BS approved plug. Features full thermostatic heat control that cuts power to the heater elements when pre-set temperature is attained and tilt safety switch. Elements designed to maximise area of the heated surface in order to transfer more heat to the atmosphere. Fitted with castors for added mobility.
SPECIFICATION
Model No: ………………………………….. RD1500.V6/RD2500.V6
Power: …………………………………………………….1500W/2500W
Size (W x D x H):………..340 x 240 x 614/480 x 240 x 624mm
Supply: …………………………………………………………………230V
ASSEMBLY
Invert the radiator after removal from packaging, oil should be heard flowing
internally under gravity, this is expected and not a problem.
Attach the castor wheels by passing the stud through the underside of the
wheel plate and securing with the supplied nut. Mount the castor wheel plate
between the first and second element of each end of the radiator. Tighten the
wing nuts on the metal “U” bolts; return the radiator to the upright position;
oil should be heard flowing internally under gravity and your heater is ready
to use when the flowing ceases fig.1.
Check the unit is the correct way up by observing carrier handle apertures are
at the top and the cable tidy is at the bottom, also the thermostat “LOW” and
“HIGH” instruction is further confirmation.
SAFETY FEATURE-: The tilt safety switch will isolate supply if accidentally
tipped over or if assembled upside down.
OPERATION
HEATING SETTINGS fig.2
Unwrap the mains lead and plug it into the power supply.
Turn the thermostat control to the highest setting.
Choose the required heat output by selecting the appropriate switch, this
switch will illumunate when pressed.
Low setting:………..Select switch with the Roman Numeral “I”.
Medium setting:….Select switch with the Roman Numeral “II”. Set switch with
“I” to off.
High setting:………Select both switches “I” and “II”.
Once the required room temperature has been achieved, turn the thermostat down
until the light on the selected heat setting switch goes out. The heater will
then keep the surrounding air at the set temperature by switching on and off
at intervals. You may reset the thermostat at any time.
To switch the unit off, turn the heat selecting switches off and unplug from
the mains. Allow the unit to cool before handling or storage.
The heater is fitted with a safety tilt switch and a thermostatic safety cut- out which will automatically turn the heater off should it be placed in circumstances that cause overheating or malfunction. Should this happen, switch the heater off and disconnect it from the mains. Allow the heater to cool before handling. Do not use the heater again until the cause has been identified and remedied. If necessary return the heater to your Sealey stockist for servicing.
When used for the first time, it is suggested that you set the heater to maximum power for a few minutes in a well ventilated room to eliminate the newness smell, typical of this type of heater.
MAINTENANCE
WARNING! Disconnect the heater from the mains power, before servicing or
performing any maintenance, which must only be carried out by an authorised
service agent with the exception of the following.
Dust the radiator (when cold) with a dry cloth.
DO NOT use a strong abrasive to clean the radiator.
When storing the heater, use the original shipping box and store in a safe, dry location. Note: Report any oil leakage immediately to an authorised service agent.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the
EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the
product is no longer required, it must be disposed of in an environmentally
protective way. Contact your local solid waste authority for recycling
information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team on technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty : Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500 01284 703534 sales@sealey.co.uk
www.sealey.co.uk
Information requirements for electric local space heaters
Model identifier(s): RD1500.V6
Item
| ****
Symbol
| ****
Value
| ****
Unit
| ****
Item
| ****
Unit
Heat output
| Type of heat input, for electric storage local space heaters only (select one)
Nominal heat output
| P nom| ****
0.7088
| ****
kW
| Manual heat charge control, with integrated thermostat| Yes No
Minimum heat output (indicative)*
* Enter figure or NA
| P min| ****
0.4377
| ****
kW
| Manual heat charge control with room and/or outdoor temperature feedback| Yes No
Maximum continuous heat output
| P max,c| ****
0.7088
| ****
kW
| Electronic heat charge control with room and/or outdoor temperature
feedback| Yes No
| Fan assisted heat output| Yes No
Auxiliary electricity consumption
| ****
Type of heat output/room temperature control (select one)
At nominal heat output| el max| ****
0.000
| ****
kW
| Single stage heat output and no room temperature control| Yes No
At minimum heat output| el min| ****
0.000
| ****
kW
| Two or more manual stages, no room temperature control| Yes No
In standby mode| el SB| ****
0.000
| ****
kW
| With mechanic thermostat room temperature control| Yes No
| With electronic room temperature control| Yes No
Electronic room temperature control plus day timer| Yes No
Electronic room temperature control plus week timer| Yes No
Other control options (multiple selections possible)
Room temperature control, with presence
detection
| Yes No
Room temperature control, with open window detection| Yes No
With distance control option
| Yes No
With adaptive start control| Yes No
With working time limitation
| Yes No
With black bulb sensor
| Yes No
Contact details: Sealey Group, Kempson Way, Suffolk Business Park, Bury St
Edmunds, Suffolk, IP32 7AR. www.sealey.co.uk
v1
ERP Table 2
Contact details: Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk, IP32 7AR. www.sealey.co.uk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>