ViewSonic VPC12-WPO-15 Slot In PC Module User Guide

: June 5, 2024
: Viewsonic

Table of Contents

View Sonic VPC12-WPO-15 Slot In PC Module
Thank you for choosing View Sonic®
Package Contents
Interface
Installation
Internet Connection
Input Selection
USB Connection
Specifications
Regulatory and Service Information
Customer Service
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

View Sonic VPC12-WPO-15 Slot In PC Module

ViewSonic VPC12-WPO-15 Slot In PC Module-FIG1

Thank you for choosing View Sonic®

As a world-leading provider of visual solutions, View Sonic® is dedicated to exceeding the world’s expectations for technological evolution, innovation, and simplicity. At View Sonic®, we believe that our products have the potential to make a positive impact in the world, and we are confident that the View Sonic® product you have chosen will serve you well. Once again, thank you for choosing View Sonic®!

Package Contents

ViewSonic VPC12-WPO-15 Slot In PC Module-FIG2

Interface

ViewSonic VPC12-WPO-15 Slot In PC Module-FIG3

Installation

ViewSonic VPC12-WPO-15 Slot In PC Module-FIG4

Internet Connection

ViewSonic VPC12-WPO-15 Slot In PC Module-FIG6

Input Selection

To select an Input Source:

Press INPUT on the remote control, press the setting button on the front panel, or press the setting icon from the toolbar to display the Input Settings menu.
Press to select PC.
Press on the remote control, or touch the input source.
Press on the remote control, or touch a blank area outside of the menu to exit.

USB Connection

ViewSonic VPC12-WPO-15 Slot In PC Module-FIG13

Specifications

Processor	Intel® Coffeelake U SOC, i5-8259U
Graphic	Intel® Iris® Plus Graphics 655
RAM	2 x DDR4 SO-DIMM, 64GB (Max)
Storage	1 x NVMe M.2 2280 SATAIII SSD
IO ports	4 x USB 3.0

1 x USB 2.0 Type-C

1 x HDMI 1.4 out

1 x RJ45 Ethernet (with Realtek 8111H) 1 x Microphone/Line out

2 x External antenna Holes 1 x Power On/ Off Button 1 x Reset Button

1 x Power LED 1 x HDD LED

1 x 80 Pin JAE OPS connector

WIFI/BT| 1 x M.2 2230 (with Intel® Dual Band Wireless-AC 3165)
vPro/AMT| No
BIOS| AMI UEFI BIOS
Power| DC in +19V @ 4.74A

65 W (Typical)

Operating Conditions| -5 °C to +45 °C

20% RH ~ 80% RH non-condensing

Storage

Conditions

| -20 °C to +70 °C

10% ~ 80% R.H. non-condensing

Regulatory and Service Information

Compliance Information
This section addresses all connected requirements and statements regarding regulations. Confirmed corresponding applications shall refer to nameplate labels and relevant markings on the unit.

CE Conformity for European Countries
The device complies with the EMC Directive 2014/30/EU and Low Voltage Directive 2014/35/EU and Radio Equipment Directive (RED) 2014/53/EU.

The following information is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE).The mark indicates the requirement NOT to dispose the equipment as unsorted municipal waste, but use the return and collection systems according to local law. In all EU member states, operation of 5150-5350MHz is restricted to indoor use only. This device should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:

Substance	Proposed Maximum Concentration	Actual Concentration
Lead (Pb)	0.1%	< 0.1%
Mercury (Hg)	0.1%	< 0.1%
Cadmium (Cd)	0.01%	< 0.01%
Hexavalent Chromium (Cr6⁺)	0.1%	< 0.1%
Polybrominated biphenyls (PBB)	0.1%	< 0.1%
Polybrominated diphenyl ethers (PBDE)	0.1%	< 0.1%
Bis (2-ethylhexyl) phthalate (DEHP)	0.1%	< 0.1%
Butyl benzyl phthalate (BBP)	0.1%	< 0.1%
Dibutyl phthalate (DBP)	0.1%	< 0.1%
Diisobutyl phthalate (DIBP)	0.1%	< 0.1%

Certain components of products as stated above are exempted under the Annex III of the RoHS2 Directives as noted below:

Copper alloy containing up to 4% lead by weight.
Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).
Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound.
Lead in dielectric ceramic in capacitors for a rated voltage of 125V AC or 250V DC or higher.

Indian Restriction of Hazardous Substances
Restriction on Hazardous Substances statement (India). This product complies with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule.

Product Disposal at End of Product Life
ViewSonic® respects the environment and is committed to working and living green. Thank you for being part of Smarter, Greener Computing. Please visit the ViewSonic® website to learn more.

Europe:
http://www.viewsoniceurope.com/eu/support/call-desk/