Jovision JVS-N95-X3 Wireless IP Camera Installation Guide
- June 5, 2024
- Jovision
Table of Contents
JVS-N95-X3 Wireless IP Camera
Installation Guide
Statement
Thank you for choosing Jovision, this user manual is intended for users of IP
Camera. It includes instructions on how to use the product. Before using the
device, read the user manual carefully. Keep this manual for further
clarifications, The descriptions, images, and technical parameters may vary
with the actual devices. The software embodied in the product Is governed by
the user license agreement covering that product
Copyright
This Manual is subject to domestic and international copyright protection,
Jovision Technology Co. Ltd. (Jovision”) reserves all rights to this manual.
This manual cannot be reproduced, changed, translated, or distributed,
partially or wholly, by any means, without the prior written permission of
Jovision
Disclaimer
This manual is for reference only. It may contain several technical incorrect
places or printing errors, and the content is subject to change without
notice, All information in this booklet has been thoroughly reviewed, and
Jovision Technology Co., Ltd. is not liable for damage caused by improper use
of this device.
Regulatory Information
FCC Statement.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected, Consult the dealer or an experienced technician for help.
RF Warning:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance 2Ocm between the radiator & your body.
EU Conformity Statement
This product and if applicable, the supplied accessories too are marked with
“CE” and comply therefore with the applicable harmonized European standards
listed under the Low Voltage Directive 2014/35/EU, the EMC Directive
2014/30/EU, the RED directive 2014/S3/EU, the RoHS Directive 2011/65/EU.
This product can be used across EU member states.
The simplified EU declaration of conformity referred to in Article 10{9) shall
be provided as follows: Hereby, (Jovision Technology Co., Ltd.) declares that
the radio equipment type (HD Network Camera) is in compliance with Directive
2014/53/EU,
2012/ 19/ EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info
|
---|---
Warnings: Follow these safeguards to prevent serious injury or death|
Cautions: Follow these precautions to prevent potential injury or material
damage.
Warnings
WARNING: This device is configured for 12V DC operation only. Do not
connect to a higher voltage. Use only with NRTL-approved Class 2 or LPS power
supplies. To prevent potential ground loop issues, a separate PSU should be
used for each camera. A multiple-output PSU may be used if the multiple output
PSU has isolated and protected (2A max) outputs.
Cautions
CAUTION: The light emitted from the near-infrared light emitting diodes
(LEDs) provides illumination over a wide area.
This light is not considered a risk to the unshielded human eye.
However, as with any light source, it is recommended that normal precautions
be taken to avoid unnecessary exposure. For example, avoid staring into the
beam or viewing the LEDs directly with optical instruments at close range.
Open Source Software License
This product contains software whose rights holders license it under the terms of the GNU General Public License, version 2 (GPLv2), version 3 (GPLv3), and/or other open source software licenses. If you want to receive the complete corresponding source code, we will provide you and any third party with the source code of the software licensed under an open source software license if you send us a written request by mail or email to the following addresses:
Jovision OSS support team Email.
opensource@jovision.com
Postal Jovision Technology Co., Ltd
Floor 12, Building 3, Aosheng Square, No.1166 Xinluo Street, Jinan City,
Shandong Province, People’s Republic of China.
Detailing the name of the product and the firmware version for which you COSTS
OF A DATA CARRIER AND THE POSTAL CHARGES TO SEND
THE DATA CARRIER TO YOU.
THE AMOUNT CAN BE VARIED ACCORDING TO YOUR LOCATION AND THE GENIATECH OS
SUPPORT TEAM WILL NOTIFY THE EXACT COST WHEN RECEIVING THE REQUEST.
THIS OFFER IS VALID FOR THREE YEARS FROM THE MOMENT WE DISTRIBUTED THE PRODUCT
ANO AND VALID FOR AS LONG AS WE OFFER SPARE PARTS OR CUSTOMER SUPPORT FOR
THAT PRODUCT MODEL.
CHANGE THE DEFAULT PASSWORD
The default account is for first-time log-in purposes only, You should change
this default password to better protect against security risks, such as
unauthorized access by others to the product that may prevent the product from
functioning properly and/or lead to other undesirable consequences.
For your privacy, we strongly recommend changing the password to something of
your own choosing (using a minimum of 8 characters, including upper case
letters, lower case letters, numbers, and special characters) in order to
increase the security of your product. Proper configuration of all passwords
and other security settings is the responsibility of the installer and/or end-
user. to the following addresses:
The product shown in the manual is just for reference only. The appearance of the products may vary with different models
Before you start:
The App interfaces on i0S and Android may different, but the functions and configuration methods are similar,
Set up Camera Network with App
-
Power on the camera.
-
Install the Cloudera Int’l App. Register an account and log in.
-
Tap the icon on the right top comer to add your camera to your account.
-
Tap AP Configuration to configure the camera.
-
Follow the instruction on the App_ “press and hold the Reset Button.
Release until hear Waiting for Configuration. Tap Next’. Wait for 15 seconds then tap Switch WL.Fi.
-
The App will redirect to the phone’s W-Fi Settings and you can find the SSID started with IPC-T-XXXXXXXX. Please select it and input 12345678 as the password. Then press Connect’. Once you connect to the Wi-Fi successfully, go back to the App.
Note: The Wi-Fi settings interface may vary depending on the smartphone user interface, -
You will be asked to confirm your home Wi-Fi network and input your password, then tap ‘Start Network’, and The App will configure device Wi-Fi. Once the Wi-Fi configuration is successful, the App will pop up the device list. Select the devices you want to add and Tap “Add” to add to the account.
-
After adding the device, it will be listed in the device list as the picture shown below. Tap on the device to connect
-
To protect user privacy, we recommend setting a strong password for the device. The app will prompt you to set the password when you access the device for the first time.
After inputting the new password, tap Save” -
Tap again on the device to see the video streaming
Here you can Enable Audio, Take a Snapshot, Record video, Change the video streaming, Talk, Control PTZ, Playback as well as Configure device settings.
Settings
Tap to access the device settings when the camera is connected. In the settings, you can modify the device OSD, Date & Time, Alarm Settings, and Device Information.
Date & Time Settings
To change the device date and time, tap “Correcting time” in the Settings.
By default, network correction is enabled. The device will sync the time with
internet time, If you are required to set the time manually, disable the
network correction and set the date and time manually.
Alarm Settings
In the Alarm Settings, you can set the Alarm Sound, Alarm Mode, Alarm Region, Sensitivity, Alarm Schedule, Enable or Disable Sound Alarm and Enable or Disable Light Alarm, etc,
-
Alarm Sound
Here you can select the sound which you want to broadcast when the device triggers an Alarm.
There are five pre-defined Alarm Sounds in the device. If you want to use a custom sound for Alarm broadcasting, tap the “Add” button to record your own audio. Tap on the “Mic” button to record and release to save. -
Alarm Mode
There is only one Motion Detection Alarm mode available in this device.
You can select Motion Detection as Alarm Mode. -
Alarm Area
Select Alarm area settings. Tap “1” and then you will get a region, You can resize the region by tapping and holding the edge of the region frame and then dragging it. You can add a maximum of 4 regions by tapping the “+” button. -
Alarm Sensitivity
Here you can set the sensitivity of the motion detection. The default sensitivity value is 60. -
Alarm Schedule
In this setting, you can schedule the motion detection and alarm time. -
Sound Alarm
When enabled, the device will broadcast a sound alarm when the motion detection is triggered. -
Light Alarm
When enabled, the device will flash its white LEDs when the motion detection is triggered.
Device Information
In device information, you can find the recording setup and storage details of
the device.
First, you need to set the recording mode, There are different modes of
recording. Al Day Recording, Disconnect Recording, Timing Recording, Alarm
Recording and Stop recording. Here you can choose the quality of recording
such as HD or SD. Also, you can set the length of the video footage. 5, 10,
20, or 30min lengths are available for the recording. 
In this setting, you can see the SD card information like Storage capacity,
Status, and used Space. To format the SD Card, Tap Format’. There will be a
confirmation pop-up.
Tap OK.
Playback
Tap for playback when the camera is connected. The App will playback the video
footage recorded on the SD Card automatically.
Technical support
If you have any problems with the device, please contact the dealer that you
purchased from. If your problem still can’t be resolved, please send an Email
to the headquarter technical support team at:
support@jovision.com
We welcome your valuable comments and suggestions on improving our products.
This device complies with part 15 of the FCC Rules, Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference,and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate equipment, This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications, However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- tncrease the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from That to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF exposure statement:
The equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. The equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body.
©2020 Jovision Technology Co., Ltd. All rights reserved.
Note: Design and specifications are subject to change without notice.
Under no circumstances, this document shall be reproduced, distributed, or
changed partially or wholly without formal authorization of Jovision
Technology Co., Ltd
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>