UBeesize VT-860 67 Inch Camera Tripod with Travel Bag User Manual
- June 15, 2024
- UBeesize
Table of Contents
UBeesize VT-860 67 Inch Camera Tripod with Travel Bag User Manual
Thank you for choosing Ubeesize.
Please read this manual sheet before using.
Warnings:
Do not exceed the tripod’s maximum load capacity.
Ensure the ballhead is locked.
Do not operate this tripod when the temperature is below -20° C or above 70° C. It is not commended to operate in saltwater.
Do not put this tripod in sunlight or lean it against the glass of car for a long time.
Do not leave this tripod unattended in public place; please be careful when use it in dangerous place.
Remove the camera from the ballhead during setup or transport.
It is not necessary to equip lubricant. Please use standard lubricant or grease when necessary.
For your safety, keep it out of power supply.
Installations
-
Introduces of the Tripod
-
The Use of the Quick Release plate (FIGURE2)
To remove the quick release plate, squeeze and pull the Plate locking lever out. The Quick Release Plate will disengage allowing it to be removed. -
The vertical panning, Horizontal rotation and 90 degree shot (FIGURE3)
a: Rotating the panning adjustment knob as the arrow shows, to loosen for smooth consistent panning, rotating oppositely to tight it.
b: Rotating the tilt adjustment knob as the arrow shows, to loosen for smooth consistent tilting, rotating oppositely to tight the tilt knob
c: rotating the rolling lock knob as the arrow shows, to adjust the angle of the loading plate flip up to 90 degree. Rotating oppositely to tight it. -
Raising and Lowering the Center Column (FIGURE 4)
To raise or lower the center column, turn the center locking knob counter- clockwise and set the column to the desired position. While holding the column in position, turn the column locking knob clockwise to secure the column in place. Don’t over tighten the center column lock, as this could damage the threads. -
Extend and fold the leg (FIGURE 5,6)
Each Leg section can be adjusted to the desired length by opening the Flip Lock Lever so the Leg is free to slide in or out. Once the desired length is achieved, snap the Flip Lock Lever closed so that the Leg Section is securely locked. Repeat this step for each Leg and each Section until the Tripod is set to the desired height. -
Weight Hook (FIGURE 7)
When additional weight is necessary to add to the tripod for stability during windy conditions, the retractable weight hook can be used to hold a sandbag, camera bag or any similar item. Take care not to overload the tripod with weight as this could have a reverse effect on increasing the tripods stability. -
Cellphone Clamp Supporting Range 2.3-3.6inches
-
Remove the quick release plate. (FIGURE 10)
-
Assemble the plate with phone mount using the 1/4 screw interface. (FIGURE 11)
-
Fasten the ring at the bottom of the quick release plate to secure the phone mount. (FIGURE 12)
Bluetooth Remote Shutter
Step 1 Pairing
A.Tum the remote on with the power switch locatedat the side. The blue LED
light will flicker.
B.Tum on your phone’s Bluetooth setting &connnect to “Bluetooth remote RL7” in
the avellable devices list. The blueLED light will stop flickering when
connected.
Step 2 Using
Open your phone’s camera app. Press thebutton associated with your phone’s operating system (ioS for iPhone. Android for Android Phones).
Note: If your camera does not respond it may notbe compatible. In this case. download the free app”Camera 360″ and use this camera app with theremote.
Step 3 Filming Videos
Switch your phone’s camera into Video mode first. Press the button to start/stop recording videos.
Note for Samsung Cell Phones:
- Go to camere setting, scroll down and tap”Volume keys function” and choose “Recordvideo”.
- Open the native camera, click the iosbutton (Not android) to start the video, clickagain to stop the video.
Official website:
www.ubeesize.com
Customer service contact:
customercare@ubeesize.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>