metabo FSX 200 Intec Random Orbital Sander Instruction Manual
- June 3, 2024
- metabo
Table of Contents
metabo FSX 200 Intec Random Orbital Sander Instruction Manual
Instructions
| FSX 200 Intec
*1) Serial Number: 09225..
---|---
D| mm (in)| 125 (5)
P 1| W| 240
P 2| W| 90
n 0| min-1 (rpm)| 11000
n 1| min-1 (rpm)| 9500
s 0| min-1 (opm)| 22000
s 1| min-1 (opm)| 19000
S| mm (in)| 2,7 (0,106)
Intec| –| ü
m| kg (lbs)| 1,3 (2.8)
a h,DS /K h,DS| m/s2| 6,5 / 1,5
a h,P /K h,P| m/s2| 14,5 / 1,5
L pA /K pA| dB(A)| 82 / 3
L WA /K WA| dB(A)| 93 / 3
2) 2014/30/EU, 2006/42/EC, 2011/65/EU
3) EN 62841:2015, EN 62841-2-4:2014, EN 50581:2012
2018-04-03, Bernd Fleischmann
Direktor Produktentstehung & Qualität (Vice President Product Engineering &
Quality)
*4) Metabowerke GmbH – Metabo-Allee 1 – 72622 Nuertingen, Germany
Conformity Declaration
We, being solely responsible, hereby declare that these orbital sanders, identified by type and serial number 1), meet all relevant requirements of directives 2) and standards 3). Technical documents for 4) – see page 3.
Specified Use
The machine is suitable for dry sanding of flat and elliptical surfaces, wood, plastics, non-ferrous metals, sheet metal and similar filled and painted surfaces.
The user bears sole responsibility for damage caused by improper use.
Generally accepted accident prevention regulations and the enclosed safety information must be observed.
General Safety Instructions
For your own protection and for the protection of your electrical tool, pay attention to all parts of the text that are marked with this symbol!
WARNING – Reading the operating instructions will reduce the risk of injury.
WARNING – Read all safety warnings, instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference. Pass on your electrical tool only together with these documents.
Special Safety Instructions
Pull the plug out of the socket before making any adjustments, changing tools, carrying out maintenance or cleaning.
Secure the workpiece against slipping, e.g. with the help of clamping devices.
Wear ear protectors when working for long periods of time. High noise levels over a prolonged period of time may affect your hearing.
Hold the machine from the handles provided.
Reducing dust exposure:
Some of the dust created using this power tool may contain substances known to cause cancer, allergic reaction, respiratory disease, birth defects or other reproductive harm. Some examples of these substances are: lead (from leadbased paints), crystalline silica (from bricks cement, etc.), additives for wood treatment (chromate, wood preservative), some types of wood (like oak and beech dust), metals, asbestos.
The risk from exposure to such substances will depend on how long the user or
nearby persons are being exposed.
Do not let particles enter the body.
To reduce exposure to these substances: work in a well ventilated area and
wear protective equipment, such as dust masks that are specially designed to
filter out microscopic particles.
Observe the relevant guidelines for your material, staff, application and place of application (e.g. occupational health and safety regulations, disposal).
Collect the generated particles at the source, avoid deposits in the surrounding area.
Use only suitable accessories. In this way, fewer particles enter the environment in an uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- Do not direct the escaping particles and the exhaust air stream at yourself or nearby persons or on dust deposits.
- Use an extraction unit and/or air purifiers.
- Ensure good ventilation of the workplace and keep it clean using a vacuum cleaner. Sweeping or blowing stirs up dust.
- Vacuum or wash protective clothing. Do not blow, beat or brush.
Overview
- Sanding disc
- Support plate
- On/off switch
- Dust collection box
- Cleaning flap
- Fluted filter
Commissioning
Before plugging in, check to see that the rated mains voltage and mains frequency, as stated on the rating label, match your power supply.
Always install an RCD with a maximum trip current of 30 mA upstream.
Installation of sanding disc
Simple attachment and removal thanks to the velcro-type fastening.
Simply press on the sanding disc such that the holes in the sanding disc (1)
are aligned with the support plate (2).
Use
Switching On and Off
Switching on:
Move switch (3) to “I” position.
Switching off:
Move switch (3) to “O” position.
Dust Extraction
To optimise the dust extraction performance, fit the sanding disc such that the holes on the sanding disc (1) are aligned to the support plate (2).
Integrated extraction system:
Install the dust collection box (4) (see illustration, page 2). To optimise
the extraction performance, empty the dust collection box (4) in good time and
clean the filter (6).
External extraction system:
Fit dust extraction nozzle (see chapter on Accessories). Connect a suitable
extraction device.
Use a suction hose with a 35 mm connector diameter. See Accessories section.
Cleaning, Maintenance
Empty dust collection box (4).
- Open cleaning flap (5).
- Empty dust collection box (4).
- Remove fluted filter (6) and knock off dust stuck to filter or remove with brush.
- When inserting, ensure that the fluted filter (6) is inserted in the lateral guides.
Clean the machine regularly. This includes vacuum cleaning the ventilation louvres on the motor.
Replacing a worn support plate (2)
- Remove fixing screws (on lower side of support plate).
- Remove support plate.
- For replacement support plates, refer to the Accessories chapter.
- Mount support plate.
- Refit fixing screws (on lower side of support plate) and tighten.
Replacing support plate brake / braking ring
If the idling speed of the support plate increases in the course of time, the
braking ring is worn and must be replaced in a service workshop for Metabo
power tools.
Note: If abrasive material (e.g. gypsum, etc.) is being sanded, the braking
ring inevitably wears faster.
Accessories
Use only genuine Metabo accessories.
6.25658
6.31216
| 5x| 25x| |
---|---|---|---|---
P 40| 6.31226| 6.31584| 2 x P 60|
P 60| 6.31227| 6.31585| 2 x P 120|
P 80| 6.31228| 6.31586| 2 x P 240| 6.31232
P 120| 6.31229| 6.31587| |
P 180| 6.31230| 6.31588| 10 x P 60|
P 240| 6.31231| 6.31589| 10 x P 120|
P 320| 6.31236| 6.31596| 5 x P 240| 6.312583
P 400| 6.31237| 6.31597| |
6.31222
6.31223
6.31242
P 100: 6.31238
P 280: 6.31239
3 x P 100
6.31215
6.25602
6.25601
Use only accessories which fulfil the requirements and specifications listed in these operating instructions.
- A Support plate with velcro-type fastening (as replacement)
- B Adhesive intermediate disc
- C Adhesive sanding discs
- D Adhesive polishing sponge
- E Lambskin adhesive polishing disc
- F Adhesive polishing felt
- G Adhesive sanding fleece
- H Adhesive sanding screen
- I Fluted filter (as replacement)
- J Dust collection box (as replacement)
- K Dust extraction connection
- L Metabo universal vacuum cleaner
For complete range of accessories, see www.metabo.com or the main catalogue.
Repairs
Repairs to electrical tools must be carried out by qualified electricians ONLY!
A defective mains cable must only be replaced with a special, original mains cable from metabo, which is available only from the Metabo service.
If you have Metabo electrical tools that require repairs, please contact your
Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from www.metabo.com.
Environmental Protection
Observe national regulations on environmentally compatible disposal and on the recycling of disused machines, packaging and accessories.
Only for EU countries: Never dispose of power tools in your household waste! In accordance with European Guideline 2012/ 19/EU on used electronic and electric equipment and its implementation in national legal systems, used power tools must be collected separately and handed in for environmentally compatible recycling.
Technical Specifications
Explanatory notes on the specifications.
Changes due to technological progress reserved.
D = Dimensions of sanding plate
P1 = Nominal power input
P2 = Power output
n0 = Idle speed
n1 = Speed at rated load
s0 = Orbital frequency at no load
s1 = Orbital frequency at nominal load
S = Oscillating circuit diameter
Intec = Dust collection box
m = Weight without mains cable
Measured values determined in conformity with EN 62841.
Machine in protection class II
~ Alternating current
The technical specifications quoted are subject to tolerances (in compliance with the relevant valid standards).
Emission values
These values make it possible to assess the emissions from the power tool and
to compare different power tools. Depending on the operating conditions, the
condition of the power tool or the accessories, the actual load may be higher
or lower.
For assessment purposes, please allow for breaks and periods when the load is
lower. Based on the adjusted estimates, arrange protective measures for the
user e.g. organisational measures.
Vibration total value (vector sum of three directions) determined in accordance with EN 62841:
ah, DS = Vibration emission value (sanding surfaces)
ah, P = Vibration emission value (polishing)
Kh,DS/Kh,P = Uncertainty (vibration)
Typical A-effective perceived sound levels:
LpA = Sound pressure level
LWA = Acoustic power level
KpA, KWA = Uncertainty
During operation the noise level can exceed 80 dB(A).
Wear ear protectors!
Metabowerke GmbH
Metabo-Allee 1
72622 Nuertingen
Germany
www.metabo.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>