Vibe DG SLATE Slate Pro Wireless Earphones User Guide
- June 5, 2024
- Vibe
Table of Contents
DG SLATE Slate Pro Wireless Earphones
User Guide
SLATE PRO WIRELESS EARPHONES CHARGING THE EARPHONES
Charge the earphones before using it for the first time.
Plug in the cable to the micro USB port and charge for at least 2 hours.
Connect the charging cable to the charging port. 
PAIRING YOUR EARPHONES
Your earphones will work best if they are within 30 ft. of your smart
device. You may experience sound briefly cutting off if you are out of range
or if your wireless connection is weak. Make sure Bluetooth is enabled on your
smartphone or tablet before starting the pairing process.
PAIRING YOUR EARPHONES (continued)
Make sure the earphones are turned off before attempting to pair it with a
smartphone or tablet.
Press and hold the “Play/ Pause” button for 5 seconds to turn on the
earphones. You will see the light flash red and blue. This indicates that your
earphones are ready to pair.
From your smartphone or tablet, find a list of nearby devices and
choose “DG-SLATE”. Enter “0000” if asked. The earphones will flash blue light
when the pairing is complete!
CONNECTION LOST?
- If pairing the earphones does not work turn off the earphones and repeat the steps again in ‘Pairing your Earphones.
- Make sure your earphones are within range of your smart device.
- If you hear a long beep, you need to recharge your earphones Connection may be lost due to low battery
- When charging your earphones, only use the enclosed USB cable.
MEDIA KEY FUNCTIONS
|
Press & Hold –
Turn devise on/off| Press Once –
Play/ Pause music
Press Twice-
Redial last number
---|---|---
| Press & Hold-
Increase volume| Press Once-
Next Trock
| Press & Hold-
Decrease volume| Press Once-
Previous Track
SPECIFICATIONS
Mode: DG-SLATE
Bluetooth Version: 5.0
Wireless Distance: Up to 33ft (10m)
Play Time: Up to 4 hours
Talk Time: Up to 3 Hours
Standby Time: Up to 80 Hours
Battery Capacity: 75 mAh
Charging Time: Up to 2 Hours
BT ID: D044460
FCC ID: 2AANZSLATE
WARNING
Keep away from water and moisture.
Keep away from heat sources.
Do not disassemble.
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet the general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.
DGL Group, Ltd. 2045 Lincoln Highway Edison, NJ, 08817. USA.
www.dglusa.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>