VIBE FB-CHBS-MC1 Pulse LED Speaker Instruction Manual
- June 4, 2024
- Vibe
Table of Contents
FB-CHBS-MC1 Pulse LED Speaker
**Instruction Manual
FB-CHBS-MC1
**
FB-CHBS-MC1 Pulse LED Speaker
PARAMETERS
• Operating distance: 10m
• Battery capacity: 300mAh
• Basic function: USB+FM+Bluetooth +LED flashing
• TWS: 1+1 couplet function
• Running time: 1.5-2hours
• Product size: 10150155mm
• Speaker size: 52mm
• Output power: 3W *1
• Input voltage (V): 5V
• SNR: >=80dB| • Product material– ABS
• Standby time: 100hours
• Speaker size: 52mm
• Impedance (Ω): 4Ω
• Frequency response range: 80HZ-20KHZ
• Charging time: 2 hours
• Package accessories: manual + USB charging cable
• BT ID: D059694
• FCC ID: 2AANZCHBS
---|---
CHARGING THE SPEAKER
The speaker comes with a built-in rechargeable lithium-ion battery. Before
using it for the first time, we recommend you charge the battery fully and
only use the supplied USB cable to charge the speaker.
Connect the USB cable to a computer USB port and the DC 5V plug to the
charging jack of the speaker. The red LED light will illuminate while the
speaker is charging.
A full charge of the battery takes around 2 hours, when the battery is fully
charged, disconnect the speaker at this point. the speaker will be ready for
use.
PAIRING THE SPEAKER
-
ensure the speaker is turned off, if it is not, please turn off the speaker first before pairing.
-
Turn the power on/off button while the LED flashes blue. this will indicate your speaker is now in pairing mode.
-
Place the speaker and the Bluetooth device to which you would like to pair it within the operating distance. we recommend keeping the two devices no further than 3 feet apart.
-
Ensure Bluetooth is enabled on your phone or music device.
refer to the manufacturer’s instructions for how to enable Bluetooth on your device. -
Once you have activated Bluetooth on your device, select the speaker “CLIP 5+RGB” From the list of available Bluetooth devices.
-
If pairing is unsuccessful, turn off the speaker first and repair following the aforementioned steps. Once you have paired the speaker with a device, the speaker will remember this device and will pair automatically when the device’s Bluetooth is activated and in range. you do not need to repair any previously connected devices.
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Please note that changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
FCC INSTRUCTIONS FOR A CLASS B DIGITAL DEVICE OR PERIPHERAL
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with a minimum distance of 20cm between the
radiator& your body
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user tis encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
DGL Group, Ltd.
195 Raritan Center Parkway, Edison, NJ 08837
www.dglusa.com
Documents / Resources
| VIBE
FB-CHBS-MC1 Pulse LED
Speaker
[pdf] Instruction Manual
FB-CHBS-MC1 Pulse LED Speaker, FB-CHBS-MC1, Pulse LED Speaker, LED Speaker,
Speaker
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>