VIBE POWERBOX1000.1-V7 Mono Car Audio Amplifier Owner’s Manual
- June 4, 2024
- Vibe
Table of Contents
VIBE POWERBOX1000.1-V7 Mono Car Audio Amplifier
Owners Manual
Congratulations on purchasing your VIBE amplifier. Please read this manual in
order to fully understand how to get the best results from this product and
ensure that all advice on how to look after the product is followed.
Thank you for buying VIBE, we hope you enjoy listening to your product as much
as we enjoyed creating it.
Attention
An aftermarket audio amplifier will place an additional load on the vehicles charging system. Most modern vehicles have sufficient capacity in the charging system as not all the electrical components of the vehicle will be switched on at once. Check the fuse rating of the amplifier and use this as the peak current requirement. Generally the continuous current draw will be a third of the peak current.
Warning
During the normal use of this amplifier the heatsink may become very hot.
Please do not touch during or immediately after use. Please ensure that when
installing this product the heatsink will not come into contact with any
materials that may be damaged by heat such as upholstery or plastics.
Limited Warranty
All VIBE products carry a full 12 month warranty, valid from the date of the
original receipt and proof of purchase. The online warranty card should be
completed within seven days of the original purchase date. The original
receipt and packaging should be retained for this twelve month period. If the
product develops a problem any stage during the warranty period, it should be
returned to the point of purchase in it’s original packaging, and complete
with no items missing. If the store is unable to repair the product it may
have to be returned to VIBE.
A full description of VIBE’s warranty information can be found on our website:
www.vibeaudio.co.uk
What Is Not Covered
- Damage to product due to improper installation.
- Subsequent damage to other components.
- Damage caused by exposure to moisture, excessive heat, chemical cleaners and / or UV radiation.
- Damage through negligence, misuse, accident or abuse. Repeated returns for the same fault may be considered abuse.
- Any cost or expense related to the removal and / or re-installation of the product.
- Damage caused by amplifier clipping or distortion.
- Items repaired or modified by any unauthorised repair facility.
- Return shipping on non defective items.
- Products returned without a returns authorisation number.
- Damage to product due to use of sealant.
International Warranty
Contact your international VIBE dealer or distributor concerning specific
procedure for your
country’s warranty policies.
www.vibeaudio.co.uk/warranty
Warning
VIBE equipment is capable of sound pressure levels that can cause permanent
damage to your hearing and those around you. Please use common sense when
listening to your audio system
and practice safe sound.
Copyright
All content included in this manual such as text, graphics, logos, icons,
images and data, are the property of Midbass Distribution Limited t/a VIBE
Technologies Limited (herein referred to as “VIBE”, “us” or “we”) and its
affiliate or their content and technology providers, and are protected by
United Kingdom and International copyright laws. All rights reserved. VIBE TV,
VIBE Arcade, Bass Box, Optisound, Cinesound, BlackAir, BlackBox, Space,
LiteAir, SLICK, BlackDeath, Bubonic, Reaper, Anti-VIBE, FastPlug, BlackHole,
QB69, VIBE Turbo Port, Vibe TurboVent, Pressure Board, Super Driver, VIBE
Pulse, VIBE Power, VIBE Digital, VIBE MAG Plugs, Ferrite Loaded, VIBE Solid
Core, VIBE OCC, VIBE FLAT, ICC, Bass Enhance, Bass Enhance+, QBass, SpeedBass,
PowerBass, N-Wedge, Box Grip, ARBSS, Supercar Series and all stylised
representations of product names, or the abbreviations of product names, as
logos are all trademarks of VIBE. Graphics and logos are trademarks or trade
dress of VIBE Technologies Ltd or its subsidiaries. VIBE’s trademarks and
trade dress may not be used in connection with any product or service that is
not VIBE’s, in any manner that is likely to cause confusion among customers or
in any manner that disparages or discredits VIBE. All other trademarks not
owned by VIBE or its subsidiaries that appear in this manual are the property
of their respective owners, who may or may not be affiliated with, connected
to, or sponsored by VIBE or its subsidiaries.
TO THE FULLEST EXTENT PERMITTED AT LAW, VIBE IS PROVIDING THIS MANUAL AND ITS
CONTENT ON AN “AS IS” BASIS AND MAKES
NO (AND EXPRESSLY DISCLAIMS ALL) REPRESENTATIONS OR WARRANTIES OF ANY KIND,
EXPRESS OR IMPLIED, WITH RESPECT TO THIS MANUAL OR THE INFORMATION, CONTENT,
MATERIALS OR PRODUCTS INCLUDED IN THIS MANUAL INCLUDING, WITHOUT LIMITATION,
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN
ADDITION, VIBE DOES NOT REPRESENT OR WARRANT THAT THE INFORMATION CONTAINED IN
THIS MANUAL IS COMPLETE OR CURRENT, AND THAT ALL SPECIFICATIONS AND
INFORMATION CONTAINED WITHIN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE.
VIBE RECOMMEND CAUTION WHEN LISTENING TO MUSIC REPRODUCED THROUGH VIBE EQUIPMENT. VIBE EQUIPMENT IS CAPABLE OF PRODUCING SOUND AND SOUND PRESSURE LEVELS THAT CAN PERMANENTLY DAMAGE HEARING OF YOU AND THAT OF OTHERS. FOR SAFE AND ENJOYABLE LISTENING, THE SOUND SHOULD BE CLEAR WITHOUT DISTORTION AT A COMFORTABLE VOLUME. BY USING ANY VIBE EQUIPMENT, YOU AGREE TO TAKE FULL RESPONSIBILITY FOR YOUR OWN SAFETY AND THE SAFETY OF OTHERS WHEN LISTENING TO MUSIC AT HIGH VOLUMES THROUGH EQUIPMENT YOU HAVE PURCHASED. USE OF ANY VIBE EQUIPMENT CONSTITUTES AGREEMENT TO THIS DISCLAIMER.
Except as specifically stated in this manual, to the fullest extent permitted at law, neither VIBE nor any of its affiliates, directors, employees or other representatives will be liable for damages arising out of or in connection with the use of this manual or the information, content, materials or products included. This is a comprehensive limitation of liability that applies to all damages of any kind, including (without limitation) compensatory, direct, indirect or consequential damages, loss of data, income or profit, loss of or damage to property and claims of third parties. For the avoidance of doubt, VIBE does not limit its liability for death or personal injury to the extent only that it arises as a result of negligence of VIBE, its affiliates, directors, employees or other representatives.
Mounting Guidelines
Your VIBE amplifier is designed with a swift installation routine in mind. Please mount the amplifier in a dry location on a solid surface. NEVER mount the amplifier upside down as this will cause the amplifier to over heat and will eventually damage the amplifier. Before fixing the amplifier in place please ensure that there is sufficient air flow around the exterior of the casing, at least two inches is sufficient to allow effective cooling.
Power Connections
Low-Level Input
High-Level Input
NOTE : When using high level input it is not necessary to connect the remote turn on wire. Do not connect both high level and low level input at the same time.
Power Cable
- At least 8 gauge cable should be used for the power connection to the amplifier.
- The power cable should be taken directly from the battery. Rubber grommets should be used when passing through any bulkheads to prevent the cable from becoming chaffed or cut.
- It is vital that a fuse / circuit breaker (of at least equal value to the one fitted in the amplifier) is placed inline with the power cable and is no further than 18 inches away from the battery.
- Please ensure that the fuse is not fitted until the entire installation procedure is complete.
Ground Cable
- At least 8 gauge cable should be used for the ground connection to the amplifier.
- The amplifier ground should be connected directly to the chassis of the vehicle, to bare metal.
- The cable length should be kept to an absolute minimum.
- It is not recommended that you connect the ground cable to the vehicles seatbelts anchor point.
Auto Turn On (High-level Input Only)
- The Powerbox amplifiers feature an auto turn-on a circuit called Autosense.
- This circuit allows the amplifier to switch on and off without a remote turn-on wire when using high-level input, for low-level input (RCA) it will still be necessary to connect the remote turn on wire from the head unit.
- When the connected source (head unit) is turned on the amplifier will turn on automatically, after the connected source (head unit) is turned off the amplifier will shut down.
RCA Cables
- Depending on the model number of your amplifier and the number of speakers you wish to power you will have to run either one or two or RCA cables from the source to the amplifier.
- Please take extra care when running these cables from the source to the amplifier. Ensure that they are placed away from all items that can generate any interference, wiring harnesses etc.
- It is recommended that the RCA cables should be run on opposite sides of the car to the previously installed power cables if possible, to avoid the cable picking up interference.
Powerbox 500.1
Terminals And Connections
-
High level input
For connection to the speaker output of your source (head unit). This is to be used if the source (headunit) does not have a low level output. -
Low level output
RCA output used to connect an additional amplifier or audio device. -
Low level input
For connection to any source (head unit) with a low level output. This is your RCA output from the source (headunit) -
Gain control
This control is used to match the input signal of the source to the amplifier. See the setup section for more details. -
Phase control
This control is used to set the phase of the amplifier and is adjustable between 0° and 180°. -
Bass boost control
This control is used to add bass boost to the amplifier centred at 45Hz and is adjustable between 0 and +12dB -
Remote level control port
For connection to the supplied remote level control for the amplifier. -
Subsonic filter frequency control
This control is used to set the subsonic filter frequency for channel 5 of the amplifier.
The frequency is adjustable between 10Hz and 50Hz. -
Low Pass Filter (LPF)
This control is used to set the crossover frequency for the amplifier when LPF is selected. The frequency is adjustable between 30Hz and 150Hz. -
Speaker terminals
Used to connect speaker cables to the amplifier. See the wiring configuration section for more details -
Power / protect LED
If the amplifier is operating normally, the GREEN LED will illuminate.
If the amplifier is in protection mode the RED LED will illuminate. -
Fuse
Replace with only the same value ATC fuse : 2 x 30A -
Power terminals
Used to connect DC power to the amplifier. See the power connections section for more details
NOTE:
When using high level input, the REM terminal will now output a +12v feed that
can be used to turn other devices in the system that do not have auto turn on.
Powerbox 500.1
Dual Subwoofer Wiring Configuration
Single Subwoofer Wiring Configuration
Powerbox 1000.1
Terminals And Connections
-
High level input
For connection to the speaker output of your source (head unit). This is to be used if the source (headunit) does not have a low level output. -
Low level output
RCA output used to connect an additional amplifier or audio device. -
Low level input
For connection to any source (head unit) with a low level output. This is your RCA output from the source (headunit) -
Gain control
This control is used to match the input signal of the source to the amplifier. See the setup section for more details. -
Phase control
This control is used to set the phase of the amplifier and is adjustable between 0° and 180°. -
Bass boost control
This control is used to add bass boost to the amplifier centred at 45Hz and is adjustable between 0 and +12dB -
Remote level control port
For connection to the supplied remote level control for the amplifier. -
Subsonic filter frequency control
This control is used to set the subsonic filter frequency for channel 5 of the amplifier.
The frequency is adjustable between 10Hz and 50Hz. -
Low Pass Filter (LPF)
This control is used to set the crossover frequency for the amplifier when LPF is selected. The frequency is adjustable between 30Hz and 150Hz. -
Speaker terminals
Used to connect speaker cables to the amplifier. See the wiring configuration section for more details -
Power / protect LED
If the amplifier is operating normally, the GREEN LED will illuminate.
If the amplifier is in protection mode the RED LED will illuminate. -
Fuse
Replace with only the same value ATC fuse : 3 x 40A -
Power terminals
Used to connect DC power to the amplifier. See the power connections section for more details
NOTE:
When using high level input, the REM terminal will now output a +12v feed that
can be used to turn other devices in the system that do not have auto turn on.
Powerbox 1000.1
Dual Subwoofer Wiring Configuration
Single Subwoofer Wiring Configuration
Set-Up Section
To correctly set the gain control of the amplifier to match that of the source (headunit) use the following setup routine:
-
Turn the gain control to minimum on the amplifier.
-
Ensure the bass boost is set to 0 dB.
Set all crossovers on the headunt ( if applicable) to flat and both bass and treble to zero. -
Turn up the source (headunit) to approx 3/4 volume.
-
Very slowly turn up the gain on the amplifier until distortion can be heard in any of the
speakers or until the volume reaches an uncomfortable listening level when this is reached turn the gain control down slightly.
The gain control is now set.
The setting of the crossover will depend on what kind of speaker you are
installing.
For a subwoofer it is recommended that the crossover is set to low pass and
the frequency is set to match that of the speakers specifications, or your
preferred frequency – this is usually around 60 – 120 Hz
Note : The smaller the speaker, the less bass it can handle. By using the
crossovers correctly you will not only lengthen the life of your speakers but
you will also get better performance from them.
To optimise your setup seek the advise of a professional installation engineer
or visit your local VIBE audio dealer.
Specification
UK Technical Enquiries
Call 09067031420
Calls cost 50p per minute. Call costs correct at date of publication
(01/02/12)
Hours of business 9.00am – 5.30pm GMT Monday – Friday. All calls are recorded
for training purposes.
MIDBASS Distribution
PO Box 11000
B75 7WG
International Technical Enquiries
For international technical support please contact the distribution agent for
your country.
Please visit www.vibeaudio.co.uk/contact
for more details.
Designed and engineered in England
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>