ring 5C28S6 TPUB Alarm Bear Glass Break Sensor User Manual

: June 5, 2024
: Ring

Table of Contents

IMPORTANT PRODUCT INFORMATION
BATTERY SAFETY
PRODUCT SPECIFICATIONS
RECYCLING YOUR DEVICE PROPERLY
FOR CONSUMERS IN THE USA
FCC Compliance Statement
FOR CONSUMERS IN CANADA
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ring 5C28S6 TPUB Alarm Bear Glass Break Sensor User Manual

IMPORTANT PRODUCT INFORMATION

SAFETY INFORMATION
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE.

WARNING: Your device should only be used in accordance with the specific instructionsfor use and intended purpose of the device. Using your device in any way other than itsintended purpose could cause injury to yourself, others and/ or damage to the device or property.

WATCH FOR SMALL PARTS! Your device and accessories may present a choking hazard to small children. Keep them out of reach of small children.

CAUTION: The device is not waterproof and as such should not be submerged in water, doing so could cause injury to yourself, others and/or damage to the device.

CAUTION: To reduce the risk of falling, take extra caution when using a ladder orsimilar equipment to mount the product.

BATTERY SAFETY

This product contains alkaline batteries. This device requires batteries for use.
Only use new 1.5V alkaline AA-sized batteries. Never mix old and new batteries. Keep all of the batteries out of the reach of children. Do not open, disassemble, puncture, cut, bend, shred or heat the batteries and do not allow metal objects to touch the battery terminals on the device as they can become hot and cause burns. Remove all batteriesif they are worn out or before storing your Device for an extended period of time. Dispose of all batteries in accordance with applicable laws and regulations and do not dispose of batteries by throwing them into a fire. If any batteries begin to leak, take steps to prevent the fluid from coming into direct contact with skin or clothes as the fluid could be corrosive and may be toxic. Remove the batteries and clean the battery compartment in accordance with the battery manufacturer’s recommendations.

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recom – mended by the manufacturer. Dispose of the used batteries according to the manufacturer’s instructions.

Maintaining Your Ring Glass Break Sensor
The Ring Glass Break Sensor is for indoor use only. Use only accessories supplied with your device, or specifically marketed for use with your device, to power your device.

PRODUCT SPECIFICATIONS

Device Name: Ring Glass Break Sensor
Model Number: 5C28S6
Electrical Rating: 3 AA Alkaline Batteries (1.5V)
Temperature Rating: 32°F to 120°F (0°C to 49°C)

RECYCLING YOUR DEVICE PROPERLY

In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of, or recycle, your device in accordance with your local laws and regulations. For information about recycling your device, go to amazon.com/devicesupport.

Terms of Service and Warranty
By purchasing or using the product, you agree to the Terms of Service found at ring.com/terms. For information on our warranty visit ring.com/legal.

FOR CONSUMERS IN THE USA

Supplier’s Declaration of Conformity — Compliance Information Statement
Unique Identifier: Ring Glass Break Sensor
Model Number: 5C28S6
FCC ID: 2AB2Q5C28S6

Responsible Party and Party issuing Supplier’s Declaration of Conformity Ring LLC, 1523 26th St., Santa Monica, CA 90404
www.ring.com / legal@ring.com

FCC Compliance Statement

This device complies with part 15 of the FC Rules. Operation issubject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Conned the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Pursuant to Section 15.21 of the FCC rules, changes or modifications to a Product by the user that are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

The device meets the FCC Radio Frequency Emission Guidelines. Information on the product is on file with the FCC and can be found by inputting such Product’s FCC ID (which can be found on the device) into the FCC ID Search form available at fcc.gov/oet/ea/fccid.

Information Regarding Exposure to Radio Frequency Energy
The output power of the radio technology used in the Products is below the radio frequency exposure limits set by the FCC. Nevertheless, it is advised to use this product in such a manner that minimizes the potential for human contact during normal operation. This device should be installed and operated with at least 20 cm between the radiator and your body.

FOR CONSUMERS IN CANADA

Innovation, Science and Economic Development Canada (ISED) Compliance IC ID: 10256A-5C28S6

This device contains licence-exempt transmitter(s)/ receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

Information Regarding Exposure to Radio Frequency Energy
This equipment complies with IC RSS-102 RF exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.