iMars TP04 Portable Tire Inflator Instruction Manual
- June 5, 2024
- iMars
Table of Contents
iMars TP04 Portable Tire Inflator
INTRODUCTION
The product is a portable tire inflation pump, which is suitable for inflation of SUv, the following small car tires and ball products. This product is safe to use, easy to operate, and equipped with high-brightness LED lighting. Please read the instructions in the manual carefully before operating.
Product Parameters Specifications
- Product scale: 166 81*44MM
- Product weight: 630G
- product material: PC
- LED lighting: 100Im (can be divided into three gear switching: long light, fast flash and SOS)
- Power symbol: The battery power symbol is divided into three grids (three grids are displayed above 11V, two grids are displayed for 11V-10V, one grid is displayed for 10V-9V, and the battery power symbol is empty and flashes below 9V)
- Rated voltage: 12.6V
- Rated power: 100W
- Maximum current: <8A
- Maximum air volume: 35L/MIN
- Pressure display range: 3-150PSI
- Maximum inflation pressure: 13OPSI (road bike)
- Pressure accuracy: 1.5%PSI
- Pressure units: PSI, BAR, KPA, KG/CM2
- Inflation speed: when the built-in battery is fully charged, it takes about1 minute for bicycles, about 2 minutes for motorcycles, and more than 4 minutes for car 195/60/R14 tires
- Power supply mode: built-in 2000mAH*3 18650 battery pack can be\ charged, or use the vehicle 5521 DC plug power cord for emergency power supply (when the built-in battery has no power)
- Operating temperature: -20 degrees Celsius to +50 degrees Celsius
- Charging cable: 5V2A Type-C (100CM)
Instructions
- Screw the air tube provided in the package to the inner copper part of the product and the air nozzle of the other end of the tire, and start inflation if there is no air leakage.
- Press the “Switch” button for 3 seconds to start the machine. The machine displays the full display interface, and then skip to the preset interface. The reading is “0”, and then press the “Setting” key again to enter the mode selection (four modes are: automobile, motorcycle, bicycle and basketbal). When the preset value appears in the mode, press the “Setting” button in turn to select the desired mode, and long press the “Switch” button to turn off.
- To switch units, press the “Setting” key for three seconds, and the units in the next line start to skip. Press the “Setting” key in turn to select the required pressure unit
- Press the”- key to enter the pressure preset mode, and the preset value starts to flash. At this time, short press the “+” or “-” key to set the preset value, and long press to enter the fast forward or fast backward mode
- Press the “+” key to enter the pressure preset mode, and the preset value starts to flash. At this time, short press the “+” or “” key to set the preset value, and long press to enter the fast forward or fast backward mode
- After the preset pressure value stops flashing and completes the operation, press the “switch” button to start inflation, and the machine will automatical- ly stop when the preset value is reached (during the inflation process, pressing the “switch” button can also stop inflation)
- Whether it is on or off, press the button of the light to turn on the LEDlighting (long light, fast flash, SOS)
- The built-in battery charging is equipped with a 5v2A Type-C charging cable. When the built-in battery is out of power, you can use the matching vehicle power cable to provide emergency power to inflate the tire.
- Voltage detection: Press the “+” and “” keys at the same time to display the real-time voltage of the current battery
- 5V2A USB output
Usage of LED lighting
The air pump is equipped with a 100 lumen bright LED lighting, which is convenient for you to inflate your tires in the dark. There are three modes of LED lighting, namely long light, fast flash and SOS. When the fourth time is pressed, the LED lighting is turned off, and the cycle continues. It is worth mentioning that, whether it is turned on or turned off, pressing the button of the light can turn on the LED lighting.
How to charge
- When the built-in battery has no power, the external vehicle power cord (dc5521) can be used to supply power to the product. The on-board powe cord is only for emergency pumping and cannot be used to charge the product for a long time.
- The air pump is equipped with a 5V2A Type-C charging cable. Afterconnecting to a standard charger for charging, the power symbol on theproduct display starts to flash, and the charging is complete when it stop flashing.
- When the air pump is completely out of power, it takes 3-4 hours to fully charge.
- Connecting the charger will automatically activate the internal battery protection circuit, and the air pump will automatically turn on.
Precautions
-
When the battery is low (below 9.6V), “LO” will be displayed on the LCD forthree seconds. After three seconds it will keep showing LO. In order to protect the performance of the product, the air pump will not work to remind you to charge the air pump in time
-
If the air pump fails to work due to improper operation or random pressing of buttons, the device can be restarted to return to normal. Restart method: After long pressing the “Switch” button, the screen turns off.
-
The TP04 air pump is suitable for inflating bicycles, motorcycles, lawn mower tires, medium-sized cars (including SUVs) and ball products, but does not support large truck tires, trucks, buses, RVs and so on.
-
The rated voltage of the cigarette lighter charger is 12.6V, so when the power supply voltage of the car is too high or too low, the device will not work properly.
-
During long-term operation, the main body of the machine may become hot. In order to prolong the service life of the product, the excessive continuous use of the air pump will activate the temperature protection function, the machine will automatically stop, and the device can be reused after 5-10 minutes.
-
It is forbidden to use gas pumps around flammable and explosive gases and liquids (such as natural gas, gas stations and so on)
-
Do not touch the position with the high temperature warning sign with your hands, wait until it cools down before operating
-
When not in use for a long time, it is recommended to fully charge the air pump every three months
-
In order to ensure safe transportation, the product is only charged about
30% before it is delivered to you, so we recommend that you fully charge the product before the first use -
Please make sure to use the original charger to charge the air pump
-
This product is not a toy, children should not play