ergotron 67C32071 LX Desk Monitor Arm User Guide

: June 5, 2024
: ERGOTRON

Table of Contents

Package Content
**
Desk Placement Options
**Rotate – Portrait/Landscape
Adjustment Step
Safety
- Weight Capacity
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ergotron 67C32071 LX Desk Monitor Arm

Package Content

Part Number Desk Thickness
98-477: 12-18 mm (0.47”- 0.71″)
98-478: 18-25 mm (0. 71 “- 0.98″)
98-479: 25-35 mm (0.98″- 1.38”)

Your product comes with only one of these clamp dimensions. The other size clamps are sold separately.

NOTE: Product movements and spring adjustments may not work until mounted and all equipment has been attached.

**

Tools Needed
**

Desk Placement Options

Your product comes with only one of these clamp dimensions. The other size clamps are sold separately.
Warning: Failure to match your desk thickness with your clamp specifications will cause an unstable condition and may result in equipment damage and or personal injury.

**Rotate – Portrait/Landscape

**

Adjustment Step

Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or difficult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.

**Lift – Up and down

**

Increase Lift Strength
If the mounted weight is too heavy or this product does not stay up when raised, then you’ll need to increase Lift Strength:| Decrease Lift Strength
If the mounted weight is too light or this product does not stay down when lowered, then you’ll need to decrease Lift Strength:
---|---

Tilt – Forward and Backward

Increase Friction
If this product moves too easily, then you’ll need to increase friction:| Decrease Friction
If this product is too difficult to move, then you’ll need to decrease friction:
---|---

CAUTION: DO NOT remove screw. Removing screw may cause damage to equipment.

Arm Swing – Side-to-side

Increase Friction
If this product moves too easily, then you’ll need to increase friction:| Decrease Friction
If this product is too difficult to move, then you’ll need to decrease friction:
---|---

Safety

Warning: Because mounting surface materials can vary widely, it is imperative that you make sure mounting surface is strong enough to handle mounted
product and equipment.

Caution: Leave enough slack in cable to allow full range of motion.
To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual. Failure to follow these instructions may result in equipment damage or personal injury

	⚠ WARNING

Move Arm to highest position before removing equipment or serious personal injury and/or damage may occur

WARNING! Stored Energy Hazard: The arm mechanism is under tension and will move up rapidly, on its own, as soon as attached equipment is removed. For this reason, DO NOT remove equipment unless the arm has been moved to the highest position! Failure to follow this instruction may result in serious personal injury and/or equipment damage!

CAUTION: For Desk Clamp installations: Do Not rotate display past edge of desk

Weight Capacity

CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!

The lower most range of motion for vertical lift is decreased up to 4.5″ (114 mm) when arm is adjusted to hold over 20Ibs (9 kgs).

Removing from desk: Remove monitors then put pressure forward while loosening boll.

Learn more about ergonomic computer use at:www.ergotron.com/ergonomics

www.ergotron.com
USA: 1-800-888-8458
Europe: +31 (0)33-45 45 600
China: 400-1 20-3051
Japan: japansupport@ergotron.com

NOTE: When contacting customer service, reference the serial number.

www.ergotron.com | USA: 1-800-888-8458 | Europe: +31 (0)33-45 45 600 | China: 400-120-3051 |Japan: japansupport@ergotron.com

While Ergotron,lnc.makes every effort to pfOvide accurate and complete information on the ins tal atlon and use of its products, it wil not be held l!able for any editofial err’ors or omissions (Including those made in the process of transla tion from English to another language), or for ind dental, special or consequential damage5 of any nature resulting from furnishing this instruction and performance of equipment in connection with this instn.1ction. Ergotron, Inc. re serves the right to make changes in t he product design and/or product documentation without notification to its users. For the most current product information, or to know if this document is available in languages other than those herein, please contact Ergotron. No part of this publication may be reproduced, stored in a retrieval system, or transmlned in any form or by any means, electronic, mechanical, photocopying, record log or otherwise without the prior wtitte-1’\ consent of Ergotton, Inc., 1181 Trapp Road, Eagan. Minnesota, 55121, USA Patents Pending and Patented U.S. & Foreign.Ergolron is a registered trademark of Ergouon, Inc.