Thermador T24UR925DS Built-In Undercounter Double Drawer Refrigerator User Guide
- June 5, 2024
- Thermador
Table of Contents
- Thermador T24UR925DS Built-In Undercounter Double Drawer Refrigerator
- Important Safety Instructions
- Tools needed for installation
- Materials supplied
- Installing the appliance
- Ventilation
- Connecting the appliance
- Installing the anti-tip-brackets
- For under-counter use
- Installing the overlay panel
- Customer Service Information
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Thermador T24UR925DS Built-In Undercounter Double Drawer Refrigerator
Important Safety Instructions
READ AND SAVE THESE INSTRUCTIONS!
These installation instructions are intended for use by qualified installers.
In addition to these instructions, the appliance shall be installed:
- In the United States, in accordance with the National Electric Code/State and municipal codes and/or local codes.
- In Canada, in accordance with the Canadian Electric Code C22.1 –latest edition/Provincial and Municipal codes and/or local codes.
Be sure to observe all listed warnings and cautions.
Look for the triangles with exclamation marks inside.
WARNING:
This indicates that death or serious injury may result due to the non-
observance of this warning.
CAUTION:
This indicates that minor or moderately severe injury may result due to the
non-observance of this warning.
NOTE:
This is used to draw the user’s attention to something in particular.
State of California Proposition 65 Warnings
This product may contain a chemical known to the State of California, which
can cause cancer or reproductive harm. Therefore, the packaging of your
product may bear the following label as required by California:
Important
- NEW INSTALLATION – If the appliance is a new installation, most of the work must be done before the unit is moved into place.
- REPLACEMENT – If the appliance is replacing another appliance, the connections for the appliance being replaced must be checked for compatibility with the new unit and replaced as necessary.
Inspect the Refrigerator
Remove all tape, packaging, and plastic covers. After unpacking the appliance
and prior to installation, thoroughly inspect the Refrigerator for possible
freight or cosmetic damage. Report any damage immediately.
NOTE:
Please do not discard any bags or items that come with the original package
until after the entire installation has been completed!
Tools needed for installation
These are the tools that you may need for the installation of the appliance. However, if you need to modify the counter or cabinetry to fit the unit, you may need other tools to make counter/cabinetry modifications before installing the appliance.
Materials supplied
- Anti-tip-bracket. 2 pieces. Screws: 2 pieces. 1 Insulating Foam (Not illustrated) 20 1/2” (520mm) x 29 1/8” (740mm) x 1/8” (3mm)
- KIT ALSO INCLUDES ONLY FOR T24UR905DP MODELS: Wood Screws:8 pieces Overlay support: 8 pieces
Installing the appliance
Most of the installation work must be done before the Refrigerator is moved into place. Have a Qualified technician install and connect the appliance according to the enclosed installation instructions.
WARNING:
Do not install this appliance:
- Outdoors
- In an environment with dripping water
- In rooms where there is a risk of frost
Transporting
The appliance is heavy and must be handled with caution during transportation
and installation. Because of the weight and dimensions of the appliance, at
least two persons are necessary to move the appliance into position securely
and avoid injuries to people or damage to the appliance.
General measures
Note: With the legs fully retracted the appliance has a minimum dimension of 34 1/8” from top to bottom. The legs can be extended up to 1/2” (13mm).
Installation location
A dry, well-ventilated room is suitable as an installation location. The
installation location should not be exposed to direct sunlight and not be
placed near a heat source, e.g. a cooker, radiator, etc. If installation next
to a heat source is unavoidable, use a suitable insulating plate or observe
the following minimum distance from the heat source:
- To electric or gas oven/range 1¼” (3 cm).
- To an oil or coal-fired cooker 1113/16” (30cm).
- To another Refrigerator or Wine Reserve 1” (2.54cm).
The floor of the installation location must not give way; if necessary, reinforce the floor. The appliance must be upright and level to function correctly. For proper operation and appearance of the unit, the cabinet opening should be square and have dimensions as shown in the next diagrams.
Top view
Frontal view
Installing Side-by-Side
The appliance can be installed beside another Thermador appliance. Follow the
next dimensions and notes for the correct installation of the appliance in a
side-by-side layout.
NOTE:
Before placing the unit into the niche, adhere the Insulating Foam (included
with the product) on the side of the unit that will be placed next to the
additional appliance. Be sure that the Insulating Foam is even with the
surface of the unit and that there are no bubbles or bumps on the Insulation
Foam after adhering it to the unit.
Two Double Drawer Refrigerators are side-by-side
One Double Drawer and one swing door appliance: opening of the door should be
opposite to the Double Drawer to avoid interference or damage by hitting
.
Do not place a swing door appliance with the opening of the door right beside
the Double Drawer. The drawers and the door may impact each other damaging the
units.
Ventilation
The Refrigerator unit is ventilated only at the Toe-Kick in the base. Never
cover that area or place anything in front of it. Otherwise, the refrigeration
cooling performance will be affected, and the unit must work harder to
increase power consumption.
Connecting the appliance
After installing the appliance, wait at least 1 hour to turn on the appliance. During transportation, the oil in the compressor may have flowed into the refrigeration system. Before switching ON the appliance for the first time, clean the interior of the appliance (see chapter “Cleaning the appliance” in the Use & Care Guide).
Electrical connection
WARNING:
These installation instructions are intended for use by qualified installers.
WARNING:
Avoid the risk of an electric shock! Insert into a grounded receptacle.
Never remove the grounding phase. Do not use any adapters. Do not use any
extension cords.
WARNING:
It is the customer’s responsibility to ensure that the appliance
installation is in compliance with all national and local electrical codes and
ordinances. Non-compliance with these instructions may result in death, fire
or an electric shock.
The receptacle must be near the appliance, 61” (1550mm) to the right of the
appliance or 37” (940mm) to the left of the appliance, and also freely
accessible following installation of the appliance for future service
.
The appliance complies with protection class I. Connect the appliance to 115
V/ 60Hz alternating current via a correctly installed receptacle with the
grounded terminal. The appliance comes with a UL registered 3-wire power cord
NEMA 5-15p type. The appliance requires a 3-pole receptacle.
WARNING:
Never connect the appliance to electronic energy saver plugs
This appliance can be used with mains and sine-controlled inverters. Main
controlled inverters are used for photovoltaic systems which are connected
directly to the national grid. Sine-controlled inverters must be used for
isolated applications (e.g. on ships or in mountain lodges) which are not
connected directly to the national grid. The appliance requires a 3-pole
socket. The socket should be connected by a qualified electrician only. Where
there is a 2-pole standard wall socket, it is the responsibility of the
customer to have this socket replaced with a correctly grounded 3-pole wall
socket. Do not use any adapter plugs. Be sure that the location of your
refrigerator has a near and accessible electric socket.
It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.A 2-pole standard wall socket must be replaced with a 3-pole grounded socket. Do not use adapters.
Installing the anti-tip-brackets
The appliance includes two anti-tip brackets. If your cabinetry is not designed for the specific dimensions of your appliance, or if you plan to use the appliance as a free-standing unit, you should use these brackets to avoid your appliance tilting due to unbalanced overweight situations where both drawers are opened at the same time.
WARNING:
To avoid the appliance tilting due to unbalanced overweight do not open
both drawers at the same time. Always close one drawer before pull out
another.
For free-standing use
-
Consider the distance necessary for the appliance to be flush with the front of your cabinetry. If there is no cabinetry, put the unit close to the wall, then take the measurement of the space at the back, between the unit and the wall.
-
Based on the measured distance between the back of the unit and the wall, bend the anti-tip bracket (included with the unit) from the pointed lines to form a “step” with the same Distance measured.
Resultant formed “step”.
NOTE: The adhesive foam must be at the bottom of the step, never on the reverse side. -
Peel the adhesive foam and paste the anti-tip bracket on both sides on the back of the appliance as shown in the illustrations.
-
With the anti-tip brackets pasted on the back of the appliance, slide the appliance to the wall until the anti-tip bracket is touching the wall. Using the screws provided, fasten the anti-tip bracket to the wall for both sides.
NOTE: Do not fasten the unit to drywall. Be sure to attach the unit to a solid surface.
For under-counter use
-
Consider the distance necessary for the appliance to be flush with the front of your cabinetry.
-
Take the measurement from the top of the cabinet of the unit to the bottom of the counter. The measurement X”(mm) may vary depending on the design of the counter, an extension of the legs of the product, etc.
NOTE: the Distance = X” (mm) may vary depending on the design of your cabinetry. -
Based on the Distance = X” (mm) between the appliance and the counter, bend the anti-tip brackets included with the appliance on the pointed lines to form a “step” 1/16” (2mm) smaller than the Distance = X” (mm) measured.
Resultant formed “step”.
NOTE: The adhesive foam must be at the bottom of the step, never on the reverse side. -
Peel the adhesive foam and paste the anti-tip-bracket at the front on the top of the cabinet of the appliance, near the corners as shown in the picture:
-
Slide the appliance into the cabinet until the front of the appliance is flush with the front of the cabinetry. Check that nothing interferes or obstructs the anti-tip-bracket while sliding under the counter.
Installing the overlay panel
(For T24UR905DP models only)
If you plan to install a custom overlay panel, you will need to create the
panel yourself or consult a qualified cabinetmaker or carpenter. A full-sized
template for easier marking the hole pattern is included in the manual
package.
IMPORTANT:
- The thickness of both the overlay panels must be ¾” (19mm).
- The overlay panel must not weigh more than 10lbs (4.54kg) each.
- Overlay panels weighing more than recommended may cause damage to your appliance.
- It is recommended to have the help of a second person to install the panel.
- Use the recommended tools in the installation manual to facilitate the installation of the panel. Failure to use the recommended tools or the help of a second person may result in damage to panel and/or the appliance.
- To install the panel, use only the screws included in the “Installation Kit”.
Create the custom overlay panel using the dimensions shown.
Top Panel:
Bottom drawer:
-
Install the custom handle of your preference on the overlay panel before installing the panel on the drawer.
-
Every custom handle is different and it is the responsibility of the customer to make the necessary adjustments to place the handle on the overlay panel.
-
The screws used to affix the custom handle to the panel must be flat and flush with the surface of the panel (Fig A); if the screws are not flat, then consider making a recession on the overlay, enough to hide the head of the screw below the surface of the overlay, otherwise the screws will interfere with the correct placement of the overlay on the drawer (Fig B).
-
Remove the gasket from the top corners of the door pulling it gently. Under the gasket in each corner, there is a recess with a guide to breaking through to use as screw positions for the panel. It is not necessary to remove all the gasket, only a portion enough to make the recess accessible. After the gasket is moved break through the guides, and make sure not to damage the gasket.
Using the screws and supports included in the “installation kit”, position the support in the recess and secure the overlay panel screwing it from the inside of the drawer through the same hole left by the removed screw until the panel is firmly attached to the drawer. -
After securing the overlay to the drawer, put the gasket back in its place pressing it against its channel on the drawer until all the gasket is even and back in place. Repeat the same steps for the other drawer.
Now, the overlay panels are ready.
Customer Service Information
If service becomes necessary, contact your dealer or an authorized service center. Do not attempt to repair the appliance yourself. Any work performed by unauthorized personnel may void the warranty. If problem persists, take the following steps (in the order listed below) until the problem is corrected to your satisfaction.
-
Contact your dealer or the Thermador Authorized Servicer in your area.
-
E-mail us from the Customer Service section of our website, www.Thermador.com.
-
Write to us at the address below:
BSH Home Appliances Corporation 1901 Main Street, Suite 600 Irvine, CA 92614 -
Call us at 1-800-735-4328
Please be sure to include (if writing), or have available (if calling), the following information:
- Model Number
- Serial Number
- Date of Original Purchase
- Date Problem Originated
- Explanation of Problem
Also, if writing, please be sure to include a daytime phone number. (You will find the model number and serial number information on the label located at the right side of the bottom compartment.).
Data Rating Label
The data rating label shows the model and the serial number of your appliance.
It is located on the right side of the bottom compartment.
Service Information
For handy reference, copy the information in the form below from the data
rating plate located on the right side of the bottom compartment. Keep your
invoice for warranty validation.
References
- doucement | in der ruhe liegt die kraft
- Beyond Luxury Kitchen Appliances | Thermador
- Beyond Luxury Kitchen Appliances | Thermador