ActronAir WRE-026CS Serene Series 2 Remote Controller User Manual
- June 5, 2024
- ActronAir
Table of Contents
SERENE SERIES 2
REMOTE CONTROLLER
Operation Manual
Suitable for
Serene Series 2
| WRE-026CS | WRE-072CS |
|---|---|
| WRE-035CS | WRE-085CS |
| WRE-050CS |
IMPORTANT NOTE:
Please read this manual carefully before operating your new remote control and
keep it near the unit for future reference.
Remote Controller Specifications
| Model | RC-02 |
|---|---|
| Rated Voltage | Rated Voltage |
| Signal Receiving Range | 3.0V( Dry batteries 1.5V AAA × 2) |
| Environment | Signal Receiving Range |
Handling the Remote Controller
Inserting and Replacing Batteries
Your air conditioning unit comes with two batteries. Insert the batteries in
the remote control before use.
- Slide the rear cover from the remote control downward, exposing the battery compartment.
- Insert the batteries, paying attention to match up the (+) and (-) ends of the batteries with the symbols inside the battery compartment.
- Slide the rear cover back into place.
BATTERY NOTES
For optimum product performance:
- Do not mix old and new batteries or batteries of different types.
- Do not leave batteries in the remote control if you don’t plan on using the device for more than 2 months.
- Do not use rechargeable batteries.
BATTERY DISPOSAL
Waste Electrical & Electronic Equipment Disposal Guideline
- Do not dispose of the waste of electrical & electronic equipment with local council waste. These must be disposed of through the council-designated hazardous waste collection center.
- The equipment may contain hazardous substances, and improper or incorrect disposal may have a negative effect on human health and on the environment.
- Remove batteries and separated them from the rest of the product before disposing of them.
CAUTION
When the batteries are removed, the remote controller settings will be erased.
After inserting new batteries, the remote controller and the Air conditioning
may have different settings.
To sync their settings, press any button or adjust the settings from the
remote controller. The Air conditioning will follow the new remote controller
settings.
Tips For Using Remote Control
- Use the remote controller within a distance of 8 meters from the appliance, pointing it towards the unit. Reception is confirmed by a beep.
- The air conditioner will not receive the command if curtains, doors, other materials, and direct sunlight block the signals from the remote controller to the indoor unit.
- Remove batteries if the remote will not be used for more than 2 months.
Button and Functions
Before you begin using your new air conditioner, make sure to familiarize
yourself with its remote control. The following is a brief introduction to the
remote control itself. For instructions on how to operate your air
conditioner, refer to the Basic Functions section of this manual. 
-
ON/OFF
This button turns the air conditioner On or Off. -
TEMP UP
Increases temperate in 0.5°C increments. The maximum temperature is 30°C. -
SET
Scrolls through operation functions as follows: Breeze away Active Clean Fresh Sleep Follow Me, AP Mode Breeze, away … The selected symbol will flash on the display area, press the OK button to confirm. -
TIMER
Set timer to turn unit On or Off. 5 TEMP DOWN Decreases temperature in 0 -
O C increments. Min. temperature is 16 O C.
-
FAN SPEED
Selects fan speeds in the following order: AUTO 20% 40% 60% 80% 100% -
BOOST
Enables the unit to reach the preset temperature in the shortest possible time -
LED
Toggles the LED display and buzzer of the air conditioner buzzer to On and Off. -
HUMIDITY MODE
Adjust the room humidity during Dry to a range of 35%~ 85%. Press this button to increase the humidity by 5% increments.
NOTE: After setting, the humidity settings will display on the screen. -
ECO/GEAR
Press this button to enter the energy-efficient model in a sequence of the following:
ECO GEAR (75%) GEAR (50%) Previous setting mode ECO …… -
SWING
Starts and stops the horizontal louver movement.
Hold down for 2 seconds to initiate the vertical louver auto swing feature. -
OK
Used to confirm the selected functions. -
ECO INTELLIGENT EYE
Used to detect the occupancy in the room to save energy. -
MODE
Scrolls through operation modes as follows: AUTO COOL DRY HEAT FAN AUTO -
SCREEN
Displays the setting, indicators, and operation conditions.
Remote Screen Indicators
-
TRANSMISSION INDICATOR
Lights up when the remote sends a signal to the indoor unit. -
ECO
Displays when the ECO feature is activated. -
TIMER ON/OFF
Timer On display.
Timer Off the display. -
QUIET
QUIET feature display. -
HORIZONTAL LOUVER
SWING feature displays. -
VERTICAL LOUVER
AUTO SWING feature displays. -
FAN SPEED
Displays selected fan speed:
Quiet 1% 2% – 20%
LOW 21% – 40%
MED 41% – 60%
HIGH 61% – 80%
81% – 100%
AUTO AUTO
This fan speed can not be adjusted in AUTO or
DRY mode -
BOOST MODE
BOOST feature displays. -
TEMPERATURE/TIMER/FAN/SPEED
Displays the set temperature by default or fan speed or timer setting when using TIMER ON/OFF functions.
• Temperature range: 16 o C – 30 o C (60 o F – 86 o F)
• Timer setting range: 0-24 hrs
• Fan speed setting range: Au – 100%
• humidity setting range: 35% – 85% This display is blank when operating is FAN mode.
NOTE: To display temperature in °F, press and hold the up and down arrows for 3 seconds while the remote power is on. -
LOCK
Displays when the LOCK feature is activated. -
GEAR
Displays when the GEAR feature is activated -
MODE
Displays the current mode including:
-
INFORMATION
Information is displayed when the functions are in use.
– Breeze Away Display
– ECO Intelligent Eye Display
– Low Battery detection Display (If flashes)
– Active Clean Feature Display
– Fresh Feature Display
– Sleep Mode Display
– Follow Me Feature Display
– Access Point Mode (AP Mode)
Basic Functions
05.01. Mode Operation
NOTE
Setting Temperature Operation
- The operating temperature range for units is 16-30°C.
- You can increase or decrease the set temperature in 0.5°C increments.
| AUTO Mode
In AUTO mode, the unit will automatically select the COOL, FAN or HEAT
function
based on the set temperature.
1. Press the button to select AUTO.
2. Set your desired temperature using the or buttons.
3. Press the button to start the unit.
NOTE
FAN SPEED is disabled in AUTO mode.
---|---
| COOL mode
In COOL mode, the unit will cool the room to the desired temperature.
1. Press the button to select COOL mode.
2. Set your desired temperature using the or buttons.
3. Press the button to select the fan speed in a range of Auto-100%.
4. Press the button to start the unit.
| HEAT Mode
1. Press the button to select HEAT mode.
2. Set your desired temperature using the or buttons.
3. Press the button to select the fan speed in a range of Auto-100%.
4. Press the button to start the unit.
NOTE
As outdoor temperature drops, the performance of your unit’s HEAT function may
be affected. The system may also enter a defrost mode during the heating
cycle.
| DRY Mode (Dehumidifying)
1. Press the button to select DRY mode.
2. Set your desired temperature using the or buttons.
3. Press the button to start the unit.
NOTE
The Fan Speed is automatically set to AUTO while in the DRY mode.
FAN Mode
- Press the button to select FAN mode.
- Press the button to select the fan speed in a range of Auto-100%.
- Press the button to start the unit.
NOTE
The set temperature is disabled in FAN mode. As a result, the remote control’s
LCD screen will not display the temperature.
CAUTION
Do not put your fingers in or near the blower and suction side of the unit.
The fan inside the unit may cause injury.
05.02. Setting the Timer
TIMER ON (Auto-On Operation)
The TIMER ON feature is useful when you want the unit to turn off
automatically at the desired time.
Example:
To start the air conditioner in 6 hours.
-
While the unit is OFF, press the button.
-
Press the or buttons to adjust the time.
-
Point the remote controller to the indoor unit and wait for 1 second. The indicator will show in the remote controller and in the indoor unit panel to indicate that this function is activated.
TIMER OFF (Auto-OFF Operation)
The TIMER OFF feature is useful when you want the unit to turn off
automatically at the desired time.
Example:
To turn OFF the air conditioner in 10 hours.
-
While the unit is ON, press the button twice until the timer indicator is shown.
-
Press the or buttons to adjust the time.
-
Point the remote controller to the indoor unit and wait for 1 second. The indicator will show in the remote controller and OF in the indoor unit panel to indicate that this function is activated.
COMBINED TIMER (Setting both ON and OFF timers simultaneously)
TIMER OFF TIMER ON (On Stop-Start operation)
This feature is useful when you want to stop the air conditioner after you go
to bed and start it again in the morning when you wake up or when you return
home.
Example:
To stop the air conditioner 2 hours after setting and start it again 10 hours
after setting.
-
While the unit is ON, press the button twice until the timer indicator is shown.
-
Press the or buttons to adjust the time.
-
Point the remote controller to the indoor unit and wait for 1 second. The indicator will show in the remote controller and in the indoor unit panel to indicate that this function is activated.
-
Press the button until the timer indicator is shown.
-
Press the or buttons to adjust the time
-
Point the remote controller to the indoor unit and wait for 1 second. Both the and indicators will show, this
means that the function is activated.
TIMER ON
TIMER OFF (Off – Start – Stop operation)
This feature is useful when you want to start the air conditioner before you
wake up and stop it after you leave the house.
Example:
To start the air conditioner in 2 hours after setting, and stop it 5 hours
after setting.
-
While the unit is OFF, press the button until timer indicator is shown.
-
Press the or buttons to adjust the time.
-
Point the remote controller to the indoor unit and wait for 1 second. The indicator will show, this means that the function is activated.
-
Press the button until timer indicator is shown.
-
Press the or buttons to adjust the time.
-
Point the remote controller to the indoor unit and wait for 1 second. Both the and indicators will show, this means that the function is activated.
NOTE
When setting the TIMER, the adjustable increment is 30 minutes up to 10 hours.
After 10 hours the increment will be 1
hour up to 24 hours.
NOTE
The indoor unit must show on or off when a button is pressed. If this does not
happen timers will show as set on remote
control but will not function on the unit.
How To Use Advanced Function
06.01. SWING Function
Setting the vertical angle of airflow
While the unit is on, use the button to set the direction (vertical angle) of
airflow.
- Press the button to activate the louver. The vertical louver will swing up and down automatically.
- Press it again to stop the automatic function.
NOTE
Continue pressing the button will adjust the vertical airflow angle in five
different positions. Keep pressing the button
until the direction you prefer is reached.
Setting the horizontal angle of airflow
While the unit is on, use the button to set the direction (horizontal angle)
of airflow.
- Press and hold the button for more than 2 seconds to activate the louver. The vertical louver will swing left and right automatically.
- Press and hold it again to stop the automatic function
NOTES
When using the COOL and DRY mode, do not set the vertical louver to the
minimum angle for long periods of time. This can cause water to condense on
the louver blade, which may drop on your floor or furnishings. See Fig. 1
When using COOL or HEAT mode, setting the vertical louver to the minimum angle
can reduce the performance of the unit due to the restricted airflow.
Do not move the louver by hand. This will cause the louver to become out of
sync. If this occurs, reset the main power supply isolator of the air
conditioning to restart the unit. This will reset the louver.
During the Pre-Heat function, the louver will be in a default position.
06.02. LED Display
- Press the LED button to activate or de-activate the display on the indoor unit.
- Press and hold the LED button for more than 5 seconds until it beeps, and releases. Then press and hold again for 5 seconds then release after beeps.
- After a few seconds the room temperature shows.
- To revert to the previous display, repeat steps 2 and 3. To revert the change press the LED button until the set point shows on the indoor unit.
06.03. QUIET Function
-
Press and hold the button for more than 2 seconds to activate the Quiet Function. The quiet icon will display to indicate it is activated. The compressor will run at a reduced capacity to minimize the operational noise.
NOTE
Due to low compressor frequency operation, this may result in insufficient cooling and heating capacity. -
Holding the button again for 2 seconds turns off quiet function.
-
Pressing the button will also cancel Quiet Mode.
06.04. FREEZE PROTECTION (FP) Function
In heating operation, the preset temperature of the air conditioner can be set
to 8 o C. This will keep the room temperature steady at 8 o C and will prevent
the house from freezing when it is unoccupied in severe weather. This will
give the occupant a better head start when they go back home and turn ON the
air conditioner.
While the system is in heat mode and 16°C, press the buttons twice within 1
second. The unit will operate at high indoor fan speed with temperature
automatically set to 8 o C and display FP on the indoor unit. Press the or
or or or buttons to cancel this operation.
NOTE
The indoor panel and remote control will not indicate 8 o C during FP
Function.
06.05. LOCK
- Press and hold the Boost and Humidity buttons for at least 5 seconds to activate the lock function. A lock icon will display above the set temperature to indicate that the remote control buttons are locked.
- Press and hold the Boost and Humidity buttons for 2 seconds to de-activate the lock function. NOTES When pressing any button, the lock con will flash to indicate that the remote-control buttons are locked. All buttons are disabled whilst the control has a lock function ON.
06.06. BOOST Function
BOOST function is available on heating and cooling to accelerate the time it
takes to reach the set point.
06.07. ECO/GEAR Function
Press the button to enter energy efficient mode in the following sequence.
ECO GEAR (75%) GEAR (50%) Previous setting mode ECO ……
NOTE
This function is only available under cooling mode.
ECO Operation
- While in cooling mode, press the button. The set temperature will automatically adjust to 24°C Auto fan speed to save energy. Energy savings will take effect only when the initial set temperature is below 24°C.
- If the set temperature is already above 24°C, the fan speed will change to Auto, the set temperature will remain unchanged.
NOTES
Pressing the button or changing the mode or adjusting the set temperature to
less than 24 o C will cancel ECO Operation.
Once ECO is activated Fan can be adjusted and ECO will be displayed on the
LED.
GEAR Function
Gear mode is a setting that can limit the energy consumption output of the air
conditioner if the end user desires a reduction in their overall system energy
usage.
This will impact performance in some conditions.
Press the button to enter the following:
75%(up to 75% electrical energy consumption)
50%(up to 50% electrical energy consumption)
Previous setting mode.
06.08. Proximity Sensor
Proximity Sensor Function uses the indoor unit’s built-in infrared sensor to
detect whether the room is occupied. When the occupant is away for 30 minutes
(or more), the unit will automatically lower the system’s performance to save
energy.
The unit will automatically resume operation if the infrared sensor detects
movements or activity inside the room again.
When activated, the remote control will display
06.09. SET Function
- Press the SET button to enter the function setting.
- Keep pressing the SET or buttons to select the desired function. The symbol of the selected function will flash on the remote control display.
- Press the OK button to confirm.
Available SET functions are as follows:
BREEZE AWAY Function
This function prevents direct airflow from blowing on the occupants for a more
comfortable ambiance. This is achieved by aiming the louver higher to avoid
direct airflow.
NOTE
This feature is available under Cool, Fan, and Dry modes only.
ACTIVE CLEAN Function
The Active Clean Function washes away accumulated dust, mold, and grease that
may cause odors when it adheres to the heat exchanger. The unit will
automatically freeze the heat exchanger and then rapidly thaw the frost to
wash and drain away the accumulated dirt. When this function is activated, the
indoor unit display window shows, that after 20 to 45 minutes, the unit will
turn off automatically and cancel the Clean function and return to the
previous operation.
FRESH Function
When the FRESH function is initiated, the Ionizer/Plasma Dust Collector
(depending on models) is energized and will help to remove pollen and
impurities from the air.
SLEEP Function
When sleep function is activated it adjusts and maintains the temperature
while you sleep and can save energy.
For more detail on this function please refer to Sleep Operation in Owner’s
Manual.
NOTE
The SLEEP function is not available in FAN or DRY mode.
FOLLOW ME Function
The FOLLOW ME function enables the remote control to measure the room
temperature at its current location and send this signal to the air
conditioner at a 3-minute interval.
Measuring room temperature from the remote control (instead of an indoor unit
temperature sensor) will enable the air conditioner to optimize the
temperature around the user to ensure maximum comfort.
-
Select follow Me in the set menu.
-
To activate, press and hold the Boost button for at least seven seconds. on will display on the screen for two seconds
-
To de-activate press and the Boost button for at least seven seconds. OF will display on the screen for two seconds.
THIS PAGE WAS INTENTIONALLY LEFT BLANK
actronair.com.au
1300 522 722
©Copyright 2020 Actron
Engineering Pty Limited ABN 34 002767240. ®Registered Trade Marks of Actron
Engineering Pty Limited.
ActronAir is constantly seeking ways to improve the design of its products,
therefore specifications are subject to change without notice.
Document: 9590-4010 Ver. 3 Issue Date: 07/2022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>