JBL Stadium 10 Marine Speaker Owner’s Manual
- June 5, 2024
- JBL
Table of Contents
- JBL Stadium 10 Marine Speaker
- WHAT’S IN THE BOX
- DIMENSIONS
- SPEAKER LED WIRING
- APPLYING FOAM SEAL
- MOUNTING THE SPEAKER
- REMOVING THE TWEETER FOR SEPARATE MOUNTING (STADIUM 8 ONLY)
- FLUSH-MOUNTING THE TWEETER
- MOUNTING IN AN ENCLOSURE (STADIUM 10 ONLY)
- SEALED-BOX VOLUME (INCLUDES DRIVER DISPLACEMENT)
- VENTED-BOX VOLUME (INCLUDES DRIVER DISPLACEMENT)
- Technical Data
- Specifications
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
JBL Stadium 10 Marine Speaker
THANK YOU FOR YOUR PURCHASE
Your JBL product has been designed to provide you with the performance and
ease of operation you would expect from JBL.
ABOUT THE MANUAL
This manual describes general installation guidelines. However, please note
that proper installation of marine audio components requires qualified
experience. If you do not have the knowledge and tools to successfully perform
this installation, we strongly recommend consulting an authorized JBL dealer
about your installation options. Keep all instructions and sales receipts for
reference.
WHAT’S IN THE BOX
DIMENSIONS
SPEAKER SIGNAL
WIRING
To send signal to the JBL manne speaker, connect the positive(+) and
negative(-) speaker wires to the appropriate speaker outputs of your source
unit or amplifier. Be sure to observe proper polarity. 
SPEAKER LED WIRING
To provide power for the LEDs, plug the 24-gauge black(+), blue, green, and
red LED wires from the speaker into the included female connector, then run
the wires from the female connector to your compatible 12-volt power source or
light controller (sold separately). If using a separate controller, be sure to
connect each wire to the proper output. 
If hardwiring the LEDs directly to your power source, you can choose the color of the LEDs by connecting the black wire to the positive (+) terminal, and the appropriate R, G, and/or B single wire or combination of wires to the negative (-) terminal. There are 7 possible colors, depending on the wiring configuration you choose:
Wire connected to positive (+12V) terminal| The wire connected to
negative (-) terminal| Color produced
---|---|---
Black
| Red| Red
Green| Green
Blue| Blue
Red+ Green| Yellow
Red+ Blue| Purple
Blue+ Green| Aquamarine
Red + Blue + Green| White –
APPLYING FOAM SEAL
To help seal your installation against water, and to provide an airtight acoustic seal, apply the self-adhesive foam seal to the speaker frame.
MOUNTING THE SPEAKER
Use the included screws to mount the speaker to the location. Use the included
speed clips if necessary to provide a secure mount.
NOTE: Use caution when cutting and using screws with fiberglass to
prevent scratches and cracks. 
REMOVING THE TWEETER FOR SEPARATE MOUNTING (STADIUM 8 ONLY)
Use the included 2-pin tool to remove the tweeter from the woofer housing.
Place the pins of the tool in the holes of the tweeter grille and rotate 45
degrees clockwise to loosen and remove. 
FLUSH-MOUNTING THE TWEETER
Place the tweeter in the mounting bracket and use the tool to secure by
turning 45 degrees counter-clockwise. 
To transmit audio signal to the tweeter, make sure the woofer and tweeter are
connected with the included cable. 
Place the tweeter in the mounting location, then turn each setscrew clockwise
to tighten the mounting brackets. Use caution so as not to overtighten. Snap
the included outer ring over the mounting bracket to hide the setscrews.
MOUNTING IN AN ENCLOSURE (STADIUM 10 ONLY)
SEALED-BOX VOLUME (INCLUDES DRIVER DISPLACEMENT)
| Size | Tuning frequency |
|---|---|
| Free air | 40Hz |
| 2 ft3 (56.6L) | 52.2Hz |
| 3 ft3 (85L) | 48.3Hz |
| 4 ft3 (113L) | 46.3Hz |
VENTED-BOX VOLUME (INCLUDES DRIVER DISPLACEMENT)
| Size | Port length | Port diameter | Tuning frequency |
|---|---|---|---|
| 2 ft3 (56.6L) | 7-9/32″ (185mm) | 3-15/16″ (100mm) | 41Hz |
| 3 ft3 (85L) | 5-1/2″ (140mm) | 3-15/16″ (100mm) | 40.6Hz |
| 4 ft3 (113L) | 4-1/4″ (108mm) | 3-15/16″ (100mm) | 40.4Hz |
Technical Data
TECHNICAL DATA
THIELE-SMALL PARAMETERS
| Stadium Marine 10 ” (250mm) Subwoofer 2-ohm| Stadium Marine 10″ (250mm)
Subwoofer 4-ohm
---|---|---
Voice coil DC resistance:| Rev(OHMs)| 1.96| 3.7
Electrical inductance:| lc:Es (mH)| 10.49| 17.52
Driver radiating area:| SD (CM2)| 356.33| 356.33
Motor force factor:| Bl (TM)| 8.953| 11.491
Compliance Volume:| VAS (Liters)| 23.5| 23.8
Suspension compliance:| CMS (mm/N)| 0.131| 0.133
Moving mass, air load:| MMS (Grams)| 107.338| 106.389
Moving mass, without air load:| MMD (Grams)| 99.737| 98.789
Free-air resonance:| F5 (Hz)| 42.5| 42.4
Mechanical 0:| ****
OMS
| 9.913| 4.025
Electrical 0:| ****
O ES
| 0.699| 0.793
Total 0:| ****
OTS
| 0.653| 0.663
SPL, 1W/1m @ 4ohm:| Lm {dB)| 86.14| 85.62
Specifications
| Specifications | Stadium 6 | Stadium 8 | Stadium 10 |
|---|---|---|---|
| Continuous power handling | 100W | 200W | 300W |
| Peak power handling | 300W | 500W | 900W |
| Frequency response | 40Hz-25kHz | 30Hz-22kHz | 20Hz- 2kHz |
| Nominal impedance | 3 Ohms* | 3 Ohms* | 2 or 4 Ohms (use switch to select) |
| Sensitivity | 92dB | 92dB | 89dB |
| External diameter | 7-15/32″ (189.4mm) | 9-1/2″ (241mm) | 11- 5/8″ |
(295.3mm)
Mounting cutout diameter| 5-23/32″ (144.8mm)| Woofer: 7″ (177.4mm)
Tweeter bracket: 4-9/16″
{115.9mm)
| 9-9/16″ (235.6mm)
Total depth| 3-21/32″ (92.5mm)| 4-5/8″ {117.2mm)| 6-9/16″ {167mm)
Mounting depth| 2-9/16″ (65mm)| 3-3/16″ (80.5mm)| 4-7/8″ {123mm)
HARMAN International Industries, Incorporated 8500 Balboa Boulevard, Northridge, CA 91329 USA www.jbl.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>